From d8a0c6450f01afb22622eb78a23794f72773fbf5 Mon Sep 17 00:00:00 2001 From: Erik van der Zalm Date: Tue, 7 Feb 2012 20:23:43 +0100 Subject: [PATCH] Split the configuration file in two parts. One for common settings. One for advanced settings. --- Marlin/Configuration.h | 271 +++++-------------------------------- Marlin/Configuration_adv.h | 208 ++++++++++++++++++++++++++++ Marlin/Marlin.pde | 24 ++-- 3 files changed, 257 insertions(+), 246 deletions(-) create mode 100644 Marlin/Configuration_adv.h diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 2a0614787e..c1bcc0fae6 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -1,26 +1,13 @@ #ifndef __CONFIGURATION_H #define __CONFIGURATION_H - +// This configurtion file contains the basic settings. +// Advanced settings can be found in Configuration_adv.h +// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration // This determines the communication speed of the printer #define BAUDRATE 250000 //#define BAUDRATE 115200 -//#define BAUDRATE 230400 - -#define EXTRUDERS 1 - -// Frequency limit -// See nophead's blog for more info -// Not working O -//#define XY_FREQUENCY_LIMIT 15 - -// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end -// of the buffer and all stops. This should not be much greater than zero and should only be changed -// if unwanted behavior is observed on a user's machine when running at very slow speeds. -#define MINIMUM_PLANNER_SPEED 2.0 // (mm/sec) - -// BASIC SETTINGS: select your board type, thermistor type, axis scaling, and endstop configuration //// The following define selects which electronics board you have. Please choose the one that matches your setup // MEGA/RAMPS up to 1.2 = 3, @@ -36,7 +23,10 @@ //=============================Thermal Settings ============================ //=========================================================================== -//// Thermistor settings: +//// Temperature sensor settings: +// -2 is thermocouple with MAX6675 (only for sensor 0) +// -1 is thermocouple with AD595 +// 0 is not used // 1 is 100k thermistor // 2 is 200k thermistor // 3 is mendel-parts thermistor @@ -45,70 +35,33 @@ // 6 is EPCOS 100k // 7 is 100k Honeywell thermistor 135-104LAG-J01 -//#define THERMISTORHEATER_0 3 -//#define THERMISTORHEATER_1 1 -//#define THERMISTORHEATER_2 1 - -//#define HEATER_0_USES_THERMISTOR -//#define HEATER_1_USES_THERMISTOR -//#define HEATER_2_USES_THERMISTOR -#define HEATER_0_USES_AD595 -//#define HEATER_1_USES_AD595 -//#define HEATER_2_USES_AD595 -//#define HEATER_0_USES_MAX6675 - - -// Select one of these only to define how the bed temp is read. -//#define THERMISTORBED 1 -//#define BED_USES_THERMISTOR -//#define BED_LIMIT_SWITCHING -#ifdef BED_LIMIT_SWITCHING - #define BED_HYSTERESIS 2 //only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS -#endif -//#define BED_USES_AD595 - -#define BED_CHECK_INTERVAL 5000 //ms - -//// Heating sanity check: -// This waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature -// If the temperature has not increased at the end of that period, the target temperature is set to zero. -// It can be reset with another M104/M109 -//#define WATCHPERIOD 20000 //20 seconds +#define TEMP_SENSOR_0 -1 +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_BED 0 // Actual temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 30 // (seconds) #define TEMP_HYSTERESIS 3 // (C°) range of +/- temperatures considered "close" to the target one -//// The minimal temperature defines the temperature below which the heater will not be enabled +// The minimal temperature defines the temperature below which the heater will not be enabled It is used +// to check that the wiring to the thermistor is not broken. +// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5 -//#define HEATER_1_MINTEMP 5 -//#define HEATER_2_MINTEMP 5 -//#define BED_MINTEMP 5 - +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define BED_MINTEMP 5 // When temperature exceeds max temp, your heater will be switched off. // This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // You should use MINTEMP for thermistor short/failure protection. #define HEATER_0_MAXTEMP 275 -//#define HEATER_1_MAXTEMP 275 -//#define HEATER_2_MAXTEMP 275 -//#define BED_MAXTEMP 150 - - -// Wait for Cooldown -// This defines if the M109 call should not block if it is cooling down. -// example: From a current temp of 220, you set M109 S200. -// if CooldownNoWait is defined M109 will not wait for the cooldown to finish -#define CooldownNoWait true - -// Heating is finished if a temperature close to this degree shift is reached -#define HEATING_EARLY_FINISH_DEG_OFFSET 1 //Degree - -//Do not wait for M109 to finish when printing from SD card -//#define STOP_HEATING_WAIT_WHEN_SD_PRINTING +#define HEATER_1_MAXTEMP 275 +#define HEATER_2_MAXTEMP 275 +#define BED_MAXTEMP 150 // PID settings: -// Uncomment the following line to enable PID support. +// Comment the following line to disable PID and enable bang-bang. #define PIDTEMP #define PID_MAX 255 // limits current to nozzle; 255=full current #ifdef PIDTEMP @@ -118,28 +71,8 @@ #define K1 0.95 //smoothing factor withing the PID #define PID_dT 0.128 //sampling period of the PID - //To develop some PID settings for your machine, you can initiall follow - // the Ziegler-Nichols method. - // set Ki and Kd to zero. - // heat with a defined Kp and see if the temperature stabilizes - // ideally you do this graphically with repg. - // the PID_CRITIAL_GAIN should be the Kp at which temperature oscillatins are not dampned out/decreas in amplitutde - // PID_SWING_AT_CRITIAL is the time for a full period of the oscillations at the critical Gain - // usually further manual tunine is necessary. - - #define PID_CRITIAL_GAIN 50 - #define PID_SWING_AT_CRITIAL 47 //seconds - - //#define PID_PI //no differentail term - #define PID_PID //normal PID - - #ifdef PID_PID - //PID according to Ziegler-Nichols method -// #define DEFAULT_Kp (0.6*PID_CRITIAL_GAIN) -// #define DEFAULT_Ki (2*Kp/PID_SWING_AT_CRITIAL*PID_dT) -// #define DEFAULT_Kd (PID_SWING_AT_CRITIAL/8./PID_dT) - -// Ultitmaker +// If you are using a preconfigured hotend then you can use one of the value sets by uncommenting it +// Ultimaker #define DEFAULT_Kp 22.2 #define DEFAULT_Ki (1.25*PID_dT) #define DEFAULT_Kd (99/PID_dT) @@ -152,39 +85,19 @@ // Mendel Parts V9 on 12V // #define DEFAULT_Kp 63.0 // #define DEFAULT_Ki (2.25*PID_dT) -// #define DEFAULT_Kd (440/PID_dT) - #endif - - #ifdef PID_PI - //PI according to Ziegler-Nichols method - #define DEFAULT_Kp (PID_CRITIAL_GAIN/2.2) - #define DEFAULT_Ki (1.2*Kp/PID_SWING_AT_CRITIAL*PID_dT) - #define DEFAULT_Kd (0) - #endif - - // this adds an experimental additional term to the heatingpower, proportional to the extrusion speed. - // if Kc is choosen well, the additional required power due to increased melting should be compensated. - #define PID_ADD_EXTRUSION_RATE - #ifdef PID_ADD_EXTRUSION_RATE - #define DEFAULT_Kc (1) //heatingpower=Kc*(e_speed) - #endif +// #define DEFAULT_Kd (440/PID_dT) #endif // PIDTEMP -// extruder run-out prevention. -//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded -//#define EXTRUDER_RUNOUT_PREVENT -#define EXTRUDER_RUNOUT_MINTEMP 190 -#define EXTRUDER_RUNOUT_SECONDS 30. -#define EXTRUDER_RUNOUT_ESTEPS 14. //mm filament -#define EXTRUDER_RUNOUT_SPEED 1500. //extrusion speed -#define EXTRUDER_RUNOUT_EXTRUDE 100 - +//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit +//can be software-disabled for whatever purposes by +#define PREVENT_DANGEROUS_EXTRUDE +#define EXTRUDE_MINTEMP 190 +#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances. //=========================================================================== //=============================Mechanical Settings=========================== //=========================================================================== - // Endstop Settings #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors @@ -192,9 +105,6 @@ const bool X_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. const bool Y_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. -// For optos H21LOB set to true, for Mendel-Parts newer optos TCST2103 set to false - -#define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 #define X_ENABLE_ON 0 @@ -207,13 +117,6 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th #define DISABLE_Y false #define DISABLE_Z false #define DISABLE_E false // For all extruders -//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats. - -// Inverting axis direction -//#define INVERT_X_DIR false // for Mendel set to false, for Orca set to true -//#define INVERT_Y_DIR true // for Mendel set to true, for Orca set to false -//#define INVERT_Z_DIR false // for Mendel set to false, for Orca set to true -//#define INVERT_E*_DIR true // for direct drive extruder v9 set to true, for geared extruder set to false, used for all extruders #define INVERT_X_DIR true // for Mendel set to false, for Orca set to true #define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false @@ -222,7 +125,7 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th #define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false -//// ENDSTOP SETTINGS: +// ENDSTOP SETTINGS: // Sets direction of endstops when homing; 1=MAX, -1=MIN #define X_HOME_DIR -1 #define Y_HOME_DIR -1 @@ -238,43 +141,19 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E #define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0} // set the homing speeds (mm/min) -//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again: -#define X_HOME_RETRACT_MM 5 -#define Y_HOME_RETRACT_MM 5 -#define Z_HOME_RETRACT_MM 1 -#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially. - -#define AXIS_RELATIVE_MODES {false, false, false, false} - -#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step) - // default settings #define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200*8/3,760*1.1} // default steps per unit for ultimaker -//#define DEFAULT_AXIS_STEPS_PER_UNIT {40, 40, 3333.92, 360} //sells mendel with v9 extruder -//#define DEFAULT_AXIS_STEPS_PER_UNIT {80.3232, 80.8900, 2284.7651, 757.2218} // SAE Prusa w/ Wade extruder #define DEFAULT_MAX_FEEDRATE {500, 500, 5, 45} // (mm/sec) #define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot. #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves #define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts -#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate -#define DEFAULT_MINTRAVELFEEDRATE 0.0 - -// minimum time in microseconds that a movement needs to take if the buffer is emptied. Increase this number if you see blobs while printing high speed & high detail. It will slowdown on the detailed stuff. -#define DEFAULT_MINSEGMENTTIME 20000 // Obsolete delete this +// #define DEFAULT_XYJERK 20.0 // (mm/sec) #define DEFAULT_ZJERK 0.4 // (mm/sec) -// If defined the movements slow down when the look ahead buffer is only half full -#define SLOWDOWN - -//default stepper release if idle -#define DEFAULT_STEPPER_DEACTIVE_TIME 60 -#define DEFAULT_STEPPER_DEACTIVE_COMMAND "M84 X Y E" //z stays powered - - //=========================================================================== //=============================Additional Features=========================== //=========================================================================== @@ -285,47 +164,14 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. //define this to enable eeprom support -#define EEPROM_SETTINGS +//#define EEPROM_SETTINGS //to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out: // please keep turned on if you can. -#define EEPROM_CHITCHAT - - -// The hardware watchdog should halt the Microcontroller, in case the firmware gets stuck somewhere. However: -// the Watchdog is not working well, so please only enable this for testing -// this enables the watchdog interrupt. -//#define USE_WATCHDOG -//#ifdef USE_WATCHDOG - // you cannot reboot on a mega2560 due to a bug in he bootloader. Hence, you have to reset manually, and this is done hereby: -//#define RESET_MANUAL -//#define WATCHDOG_TIMEOUT 4 //seconds -//#endif - -// extruder advance constant (s2/mm3) -// -// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTUDER_ADVANCE_K * cubic mm per second ^ 2 -// -// hooke's law says: force = k * distance -// bernoulli's priniciple says: v ^ 2 / 2 + g . h + pressure / density = constant -// so: v ^ 2 is proportional to number of steps we advance the extruder -//#define ADVANCE - -#ifdef ADVANCE - #define EXTRUDER_ADVANCE_K .0 - - #define D_FILAMENT 2.85 - #define STEPS_MM_E 836 - #define EXTRUTION_AREA (0.25 * D_FILAMENT * D_FILAMENT * 3.14159) - #define STEPS_PER_CUBIC_MM_E (axis_steps_per_unit[E_AXIS]/ EXTRUTION_AREA) - -#endif // ADVANCE - +//#define EEPROM_CHITCHAT //LCD and SD support //#define ULTRA_LCD //general lcd support, also 16x2 //#define SDSUPPORT // Enable SD Card Support in Hardware Console -#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers? -#define SD_FINISHED_RELEASECOMMAND "M84 X Y E" // no z because of layer shift. //#define ULTIPANEL #ifdef ULTIPANEL @@ -341,60 +187,11 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th #endif #endif -// A debugging feature to compare calculated vs performed steps, to see if steps are lost by the software. -//#define DEBUG_STEPS - - -// Arc interpretation settings: -#define MM_PER_ARC_SEGMENT 1 -#define N_ARC_CORRECTION 25 - - -//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode. -//The maximum buffered steps/sec of the extruder motor are called "se". -//You enter the autotemp mode by a M109 S T F -// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp -// you exit the value by any M109 without F* -// Also, if the temperature is set to a value target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS +#endif +#define BED_CHECK_INTERVAL 5000 //ms + +//// Heating sanity check: +// This waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature +// If the temperature has not increased at the end of that period, the target temperature is set to zero. +// It can be reset with another M104/M109 +//#define WATCHPERIOD 20000 //20 seconds + +// Wait for Cooldown +// This defines if the M109 call should not block if it is cooling down. +// example: From a current temp of 220, you set M109 S200. +// if CooldownNoWait is defined M109 will not wait for the cooldown to finish +#define CooldownNoWait true + +// Heating is finished if a temperature close to this degree shift is reached +#define HEATING_EARLY_FINISH_DEG_OFFSET 1 //Degree + +//Do not wait for M109 to finish when printing from SD card +//#define STOP_HEATING_WAIT_WHEN_SD_PRINTING + +#ifdef PIDTEMP + // this adds an experimental additional term to the heatingpower, proportional to the extrusion speed. + // if Kc is choosen well, the additional required power due to increased melting should be compensated. + #define PID_ADD_EXTRUSION_RATE + #ifdef PID_ADD_EXTRUSION_RATE + #define DEFAULT_Kc (1) //heatingpower=Kc*(e_speed) + #endif +#endif + + +//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode. +//The maximum buffered steps/sec of the extruder motor are called "se". +//You enter the autotemp mode by a M109 S T F +// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp +// you exit the value by any M109 without F* +// Also, if the temperature is set to a value 0 + #define THERMISTORHEATER_0 TEMP_SENSOR_0 + #define HEATER_0_USES_THERMISTOR +#endif +#if TEMP_SENSOR_1 > 0 + #define THERMISTORHEATER_1 TEMP_SENSOR_1 + #define HEATER_1_USES_THERMISTOR +#endif +#if TEMP_SENSOR_2 > 0 + #define THERMISTORHEATER_2 TEMP_SENSOR_2 + #define HEATER_2_USES_THERMISTOR +#endif +#if TEMP_SENSOR_BED > 0 + #define THERMISTORBED TEMP_SENSOR_BED + #define BED_USES_THERMISTOR +#endif +#if TEMP_SENSOR_0 == -1 + #define HEATER_0_USES_AD595 +#endif +#if TEMP_SENSOR_1 == -1 + #define HEATER_1_USES_AD595 +#endif +#if TEMP_SENSOR_2 == -1 + #define HEATER_2_USES_AD595 +#endif +#if TEMP_SENSOR_BED == -1 + #define BED_USES_AD595 +#endif +#if TEMP_SENSOR_0 == -2 + #define HEATER_0_USES_MAX6675 +#endif + +#endif //__CONFIGURATION_ADV_H diff --git a/Marlin/Marlin.pde b/Marlin/Marlin.pde index 57eb61b8e4..e1decfd3f0 100644 --- a/Marlin/Marlin.pde +++ b/Marlin/Marlin.pde @@ -254,6 +254,12 @@ void suicide() #endif } +long millis_diff(unsigned long starttime) { + unsigned long difftime = millis() - starttime; + if (difftime > 0x8000) difftime += 0x8000; + return difftime; +} + void setup() { setup_powerhold(); @@ -550,9 +556,9 @@ void process_commands() if(code_seen('S')) codenum = code_value() * 1000; // seconds to wait st_synchronize(); - codenum += millis(); // keep track of when we started waiting +// codenum += millis(); // keep track of when we started waiting previous_millis_cmd = millis(); - while(millis() < codenum ){ + while(millis_diff(previous_millis_cmd) < codenum ){ manage_heater(); } break; @@ -843,11 +849,11 @@ void process_commands() /* continue to loop until we have reached the target temp _and_ until TEMP_RESIDENCY_TIME hasn't passed since we reached it */ while((residencyStart == -1) || - (residencyStart > -1 && (millis() - residencyStart) < TEMP_RESIDENCY_TIME*1000) ) { + (residencyStart > -1 && (millis_diff(residencyStart) < TEMP_RESIDENCY_TIME*1000) )) { #else while ( target_direction ? (isHeatingHotend(tmp_extruder)) : (isCoolingHotend(tmp_extruder)&&(CooldownNoWait==false)) ) { #endif //TEMP_RESIDENCY_TIME - if( (millis() - codenum) > 1000 ) + if(millis_diff(codenum) > 1000 ) { //Print Temp Reading and remaining time every 1 second while heating up/cooling down SERIAL_PROTOCOLPGM("T:"); SERIAL_PROTOCOL( degHotend(tmp_extruder) ); @@ -857,7 +863,7 @@ void process_commands() SERIAL_PROTOCOLPGM(" W:"); if(residencyStart > -1) { - codenum = TEMP_RESIDENCY_TIME - ((millis() - residencyStart) / 1000); + codenum = TEMP_RESIDENCY_TIME - (millis_diff(residencyStart) / 1000); SERIAL_PROTOCOLLN( codenum ); } else @@ -895,7 +901,7 @@ void process_commands() codenum = millis(); while(isHeatingBed()) { - if( (millis()-codenum) > 1000 ) //Print Temp Reading every 1 second while heating up. + if( millis_diff(codenum) > 1000 ) //Print Temp Reading every 1 second while heating up. { float tt=degHotend(active_extruder); SERIAL_PROTOCOLPGM("T:"); @@ -1293,11 +1299,11 @@ void prepare_arc_move(char isclockwise) { void manage_inactivity(byte debug) { - if( (millis()-previous_millis_cmd) > max_inactive_time ) + if( millis_diff(previous_millis_cmd) > max_inactive_time ) if(max_inactive_time) kill(); if(stepper_inactive_time) - if( (millis()-last_stepperdisabled_time) > stepper_inactive_time ) + if( millis_diff(last_stepperdisabled_time) > stepper_inactive_time ) { if(previous_millis_cmd>last_stepperdisabled_time) last_stepperdisabled_time=previous_millis_cmd; @@ -1309,7 +1315,7 @@ void manage_inactivity(byte debug) } } #ifdef EXTRUDER_RUNOUT_PREVENT - if( (millis()-previous_millis_cmd) > EXTRUDER_RUNOUT_SECONDS*1000 ) + if( millis_diff(previous_millis_cmd) > EXTRUDER_RUNOUT_SECONDS*1000 ) if(degHotend(active_extruder)>EXTRUDER_RUNOUT_MINTEMP) { bool oldstatus=READ(E0_ENABLE_PIN);