Bring configs up to date

Marlin/Configuration_adv.h

@@ -917,7 +917,7 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
-    //#define POWER_LOSS_PIN         44 // Pin to detect power loss (optional)
+    //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PURGE_LEN   20 // (mm) Length of filament to purge on resume
     //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
@@ -1159,7 +1159,7 @@
   #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
     #define DOUBLECLICK_MAX_INTERVAL 1250   // Maximum interval between clicks, in milliseconds.
                                             // Note: Extra time may be added to mitigate controller latency.
-    #define BABYSTEP_ALWAYS_AVAILABLE     // Allow babystepping at all times (not just during movement).
+    //#define BABYSTEP_ALWAYS_AVAILABLE     // Allow babystepping at all times (not just during movement).
     //#define MOVE_Z_WHEN_IDLE              // Jump to the move Z menu on doubleclick when printer is idle.
     #if ENABLED(MOVE_Z_WHEN_IDLE)
       #define MOVE_Z_IDLE_MULTIPLICATOR 1   // Multiply 1mm by this factor for the move step size.

config/examples/Anet/A6/Configuration.h

@@ -989,15 +989,14 @@
 #if 1 // 0 for less clearance
   #define Z_CLEARANCE_DEPLOY_PROBE   10 // Z Clearance for Deploy/Stow
   #define Z_CLEARANCE_BETWEEN_PROBES  5 // Z Clearance between probe points
-#define Z_CLEARANCE_MULTI_PROBE     5 // Z Clearance between multiple probes
   //#define Z_AFTER_PROBING           5 // Z position after probing is done
 #else
   #define Z_CLEARANCE_DEPLOY_PROBE    5 // Z Clearance for Deploy/Stow
   #define Z_CLEARANCE_BETWEEN_PROBES  3 // Z Clearance between probe points
-#define Z_CLEARANCE_MULTI_PROBE     5 // Z Clearance between multiple probes
   //#define Z_AFTER_PROBING           3 // Z position after probing is done
 #endif
 
+#define Z_CLEARANCE_MULTI_PROBE       5 // Z Clearance between multiple probes
 #define Z_PROBE_LOW_POINT          -2 // Farthest distance below the trigger-point to go before stopping
 
 // For M851 give a range for adjusting the Z probe offset

config/examples/Dagoma/Disco Ultimate/Configuration_adv.h

@@ -917,7 +917,7 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
-    //#define POWER_LOSS_PIN         44 // Pin to detect power loss (optional)
+    //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PURGE_LEN   20 // (mm) Length of filament to purge on resume
     //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.

config/examples/Einstart-S/Configuration.h

@@ -379,13 +379,13 @@
  *   147 : Pt100 with 4k7 pullup
  *   110 : Pt100 with 1k pullup (non standard)
  *
+ *  1000 : Custom - Specify parameters in Configuration_adv.h
+ *
  *         Use these for Testing or Development purposes. NEVER for production machine.
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  *
- *   666 : Custom table generated for 200K thermistor with 10k pullup on Einstart S
+ * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" }
- *
- * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
  */
 #define TEMP_SENSOR_0 666
 #define TEMP_SENSOR_1 0
@@ -820,6 +820,7 @@
  * or (with LCD_BED_LEVELING) the LCD controller.
  */
 //#define PROBE_MANUALLY
+//#define MANUAL_PROBE_START_Z 0.2
 
 /**
  * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
@@ -928,6 +929,7 @@
  */
 #define Z_CLEARANCE_DEPLOY_PROBE   10 // Z Clearance for Deploy/Stow
 #define Z_CLEARANCE_BETWEEN_PROBES  5 // Z Clearance between probe points
+#define Z_CLEARANCE_MULTI_PROBE     5 // Z Clearance between multiple probes
 //#define Z_AFTER_PROBING           5 // Z position after probing is done
 
 #define Z_PROBE_LOW_POINT          -2 // Farthest distance below the trigger-point to go before stopping
@@ -1970,6 +1972,15 @@
 //
 //#define SILVER_GATE_GLCD_CONTROLLER
 
+//
+// Extensible UI
+//
+// Enable third-party or vendor customized user interfaces that aren't
+// packaged with Marlin. Source code for the user interface will need to
+// be placed in "src/lcd/extensible_ui/lib"
+//
+//#define EXTENSIBLE_UI
+
 //
 // Einstart S OLED SSD1306
 //

config/examples/Formbot/Raptor/Configuration_adv.h

@@ -2261,19 +2261,19 @@
   #define USER_SCRIPT_RETURN  // Return to status screen after a script
 
   #define USER_DESC_1 "UBL Commission Step 1"
-  #define USER_GCODE_1 "M502 \n M500 \n M501 \n M190 S75 \n G28 \n G29 P1 \n G29 S1 \n M117 Run Step 2 \n"
+  #define USER_GCODE_1 "M502\nM500\nM501\nM190 S75\nG28\nG29 P1\nG29 S1\nM117 Run Step 2"
 
   #define USER_DESC_2 "UBL Commission Step 2"
-  #define USER_GCODE_2 "G29 S1 \n G29 S0 \n G29 F 10.0 \n G29 A \n M500 \n G28 \n G29 L1 \n M109 S225 \n G1 X150 Y 150 \n G1 Z0 \n M117 Set Z Offset \n"
+  #define USER_GCODE_2 "G29 S1\nG29 S0\nG29 F 10.0\nG29 A\nM500\nG28\nG29 L1\nM109 S225\nG1 X150 Y 150\nG1 Z0\nM117 Set Z Offset"
 
   #define USER_DESC_3 "Prep for Z Adjust"
-  #define USER_GCODE_3 "M190 75 \n M104 235 \n G28 \n G29 L1 \n G1 X150 Y 150 \n G1 Z0 \n"
+  #define USER_GCODE_3 "M190 75\nM104 235\nG28\nG29 L1\nG1 X150 Y 150\nG1 Z0"
 
   #define USER_DESC_4 "Fill Mesh Points"
-  #define USER_GCODE_4 "G29 P3 \n G29 P3 \n G29 P3 \n G29 T \n"
+  #define USER_GCODE_4 "G29 P3\nG29 P3\nG29 P3\nG29 T"
 
   #define USER_DESC_5 "Run Mesh Validation"
-  #define USER_GCODE_5 "G26 \n"
+  #define USER_GCODE_5 "G26"
 #endif
 
 /**

config/examples/Geeetech/A10/Configuration_adv.h

@@ -917,7 +917,7 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
-    //#define POWER_LOSS_PIN         44 // Pin to detect power loss (optional)
+    //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PURGE_LEN   20 // (mm) Length of filament to purge on resume
     //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.

config/examples/Geeetech/A20M/Configuration.h

@@ -1694,7 +1694,6 @@
 // ULTIPANEL as seen on Thingiverse.
 //
 #define ULTIPANEL
-#define NEWPANEL
 
 //
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)

config/examples/Geeetech/MeCreator2/Configuration_adv.h

@@ -2218,6 +2218,21 @@
  */
 #define FASTER_GCODE_PARSER
 
+/**
+ * CNC G-code options
+ * Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc.
+ * Note that G0 feedrates should be used with care for 3D printing (if used at all).
+ * High feedrates may cause ringing and harm print quality.
+ */
+//#define PAREN_COMMENTS      // Support for parentheses-delimited comments
+//#define GCODE_MOTION_MODES  // Remember the motion mode (G0 G1 G2 G3 G5 G38.X) and apply for X Y Z E F, etc.
+
+// Enable and set a (default) feedrate for all G0 moves
+//#define G0_FEEDRATE 3000 // (mm/m)
+#ifdef G0_FEEDRATE
+  //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
+#endif
+
 /**
  * G-code Macros
  *

config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

@@ -321,6 +321,7 @@
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
     #define AUTO_POWER_CONTROLLERFAN
+    #define AUTO_POWER_CHAMBER_FAN
     #define POWER_TIMEOUT 30
   #endif
 

config/examples/JGAurora/A1/Configuration.h

@@ -1982,7 +1982,6 @@
 // MKS Robin 320x240 color display
 // Also used for JGAurora A5S & A1 TFT LCD's (16-bit Parallel LCD via FSMC)
 #define MKS_ROBIN_TFT
-#define PRINTER_EVENT_LEDS
 
 //=============================================================================
 //============================  Other Controllers  ============================

config/examples/JGAurora/A1/Configuration_adv.h

@@ -922,7 +922,7 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
-    //#define POWER_LOSS_PIN         44 // Pin to detect power loss (optional)
+    //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PURGE_LEN   20 // (mm) Length of filament to purge on resume
     //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.

config/examples/JGAurora/A5S/Configuration_adv.h

@@ -922,7 +922,7 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
-    //#define POWER_LOSS_PIN         44 // Pin to detect power loss (optional)
+    //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PURGE_LEN   20 // (mm) Length of filament to purge on resume
     //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.

config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h

@@ -1166,6 +1166,8 @@
     #endif
   #endif
 
+  //#define BABYSTEP_DISPLAY_TOTAL          // Display total babysteps since last G28
+
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

config/examples/Tronxy/X5S/Configuration.h

@@ -445,6 +445,7 @@
 #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
   #define PID_AUTOTUNE_MENU       // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG             // Sends debug data to the serial port.
   //#define PID_OPENLOOP 1        // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX

config/examples/delta/Anycubic/Kossel/Configuration.h

@@ -1311,6 +1311,7 @@
 //#define AUTO_BED_LEVELING_UBL
 //#define MESH_BED_LEVELING
 #endif
+
 /**
  * Normally G28 leaves leveling disabled on completion. Enable
  * this option to have G28 restore the prior leveling state.

config/examples/delta/Tevo Little Monster/Configuration_adv.h

@@ -2236,6 +2236,18 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * G-code Macros
+ *
+ * Add G-codes M810-M819 to define and run G-code macros.
+ * Macros are not saved to EEPROM.
+ */
+//#define GCODE_MACROS
+#if ENABLED(GCODE_MACROS)
+  #define GCODE_MACROS_SLOTS       5  // Up to 10 may be used
+  #define GCODE_MACROS_SLOT_SIZE  50  // Maximum length of a single macro
+#endif
+
 /**
  * User-defined menu items that execute custom GCode
  */

config/examples/delta/kossel_mini/Configuration_adv.h

@@ -754,6 +754,7 @@
     #define CALIBRATION_PIN_PULLUP
   #endif
 #endif
+
 /**
  * Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies
  * below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible