From ddbe4cfa20165b5efcd8fb28078083261136cf72 Mon Sep 17 00:00:00 2001 From: Bob Kuhn Date: Tue, 26 Feb 2019 21:03:13 -0600 Subject: [PATCH] Printrboard G2 support (#13116) --- Marlin/src/HAL/HAL_DUE/G2_PWM.cpp | 145 ++ Marlin/src/HAL/HAL_DUE/G2_PWM.h | 77 + Marlin/src/HAL/HAL_DUE/G2_pins.h | 278 +++ Marlin/src/HAL/HAL_DUE/fastio_Due.h | 131 +- Marlin/src/Marlin.cpp | 12 + .../Printrbot/PrintrboardG2/Configuration.h | 2102 +++++++++++++++++ Marlin/src/core/boards.h | 6 + .../src/gcode/feature/digipot/M907-M910.cpp | 22 +- Marlin/src/module/stepper.cpp | 172 +- Marlin/src/pins/pins.h | 2 + Marlin/src/pins/pinsDebug_list.h | 9 + Marlin/src/pins/pins_PRINTRBOARD_G2.h | 177 ++ 12 files changed, 3009 insertions(+), 124 deletions(-) create mode 100644 Marlin/src/HAL/HAL_DUE/G2_PWM.cpp create mode 100644 Marlin/src/HAL/HAL_DUE/G2_PWM.h create mode 100644 Marlin/src/HAL/HAL_DUE/G2_pins.h create mode 100644 Marlin/src/config/examples/Printrbot/PrintrboardG2/Configuration.h create mode 100644 Marlin/src/pins/pins_PRINTRBOARD_G2.h diff --git a/Marlin/src/HAL/HAL_DUE/G2_PWM.cpp b/Marlin/src/HAL/HAL_DUE/G2_PWM.cpp new file mode 100644 index 0000000000..cfb064097e --- /dev/null +++ b/Marlin/src/HAL/HAL_DUE/G2_PWM.cpp @@ -0,0 +1,145 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/** + * The PWM module is only used to generate interrupts at specified times. It + * is NOT used to directly toggle pins. The ISR writes to the pin assigned to + * that interrupt. + * + * All PWMs use the same repetition rate. The G2 needs about 10KHz min in order to + * not have obvious ripple on the Vref signals. + * + * The data structures are setup to minimize the computation done by the ISR which + * minimizes ISR execution time. Execution times are 0.8 to 1.1 microseconds. + * + * FIve PWM interrupt sources are used. Channel 0 sets the base period. All Vref + * signals are set active when this counter overflows and resets to zero. The compare + * values in channels 1-4 are set to give the desired duty cycle for that Vref pin. + * When counter 0 matches the compare value then that channel generates an interrupt. + * The ISR checks the source of the interrupt and sets the corresponding pin inactive. + * + * Some jitter in the Vref signal is OK so the interrupt priority is left at its default value. + */ + +#include "../../inc/MarlinConfig.h" + +#if MB(PRINTRBOARD_G2) + +#include "G2_PWM.h" + +volatile uint32_t *SODR_A = &PIOA->PIO_SODR, + *SODR_B = &PIOB->PIO_SODR, + *CODR_A = &PIOA->PIO_CODR, + *CODR_B = &PIOB->PIO_CODR; + +PWM_map ISR_table[NUM_PWMS] = PWM_MAP_INIT; + +void Stepper::digipot_init() { + + OUT_WRITE(MOTOR_CURRENT_PWM_X_PIN, 0); // init pins + OUT_WRITE(MOTOR_CURRENT_PWM_Y_PIN, 0); + OUT_WRITE(MOTOR_CURRENT_PWM_Z_PIN, 0); + OUT_WRITE(MOTOR_CURRENT_PWM_E_PIN, 0); + + #define WPKEY (0x50574D << 8) // “PWM” in ASCII + #define WPCMD_DIS_SW 0 // command to disable Write Protect SW + #define WPRG_ALL (PWM_WPCR_WPRG0 | PWM_WPCR_WPRG1 | PWM_WPCR_WPRG2 | PWM_WPCR_WPRG3 | PWM_WPCR_WPRG4 | PWM_WPCR_WPRG5) // all Write Protect Groups + + #define PWM_CLOCK_F F_CPU / 1000000UL // set clock to 1MHz + + PMC->PMC_PCER1 = PMC_PCER1_PID36; // enable PWM controller clock (disabled on power up) + + PWM->PWM_WPCR = WPKEY | WPRG_ALL | WPCMD_DIS_SW; // enable setting of all PWM registers + PWM->PWM_CLK = PWM_CLOCK_F; // enable CLK_A and set it to 1MHz, leave CLK_B disabled + PWM->PWM_CH_NUM[0].PWM_CMR = 0b1011; // set channel 0 to Clock A input & to left aligned + PWM->PWM_CH_NUM[1].PWM_CMR = 0b1011; // set channel 1 to Clock A input & to left aligned + PWM->PWM_CH_NUM[2].PWM_CMR = 0b1011; // set channel 2 to Clock A input & to left aligned + PWM->PWM_CH_NUM[3].PWM_CMR = 0b1011; // set channel 3 to Clock A input & to left aligned + PWM->PWM_CH_NUM[4].PWM_CMR = 0b1011; // set channel 4 to Clock A input & to left aligned + + PWM->PWM_CH_NUM[0].PWM_CPRD = PWM_PERIOD_US; // set channel 0 Period + + PWM->PWM_IER2 = PWM_IER1_CHID0; // generate interrupt when counter0 overflows + PWM->PWM_IER2 = PWM_IER2_CMPM0 | PWM_IER2_CMPM1 | PWM_IER2_CMPM2 | PWM_IER2_CMPM3 | PWM_IER2_CMPM4; // generate interrupt on compare event + + PWM->PWM_CMP[1].PWM_CMPV = 0x010000000LL | G2_VREF_COUNT(G2_VREF(motor_current_setting[0])); // interrupt when counter0 == CMPV - used to set Motor 1 PWM inactive + PWM->PWM_CMP[2].PWM_CMPV = 0x010000000LL | G2_VREF_COUNT(G2_VREF(motor_current_setting[0])); // interrupt when counter0 == CMPV - used to set Motor 2 PWM inactive + PWM->PWM_CMP[3].PWM_CMPV = 0x010000000LL | G2_VREF_COUNT(G2_VREF(motor_current_setting[1])); // interrupt when counter0 == CMPV - used to set Motor 3 PWM inactive + PWM->PWM_CMP[4].PWM_CMPV = 0x010000000LL | G2_VREF_COUNT(G2_VREF(motor_current_setting[2])); // interrupt when counter0 == CMPV - used to set Motor 4 PWM inactive + + PWM->PWM_CMP[1].PWM_CMPM = 0x0001; // enable compare event + PWM->PWM_CMP[2].PWM_CMPM = 0x0001; // enable compare event + PWM->PWM_CMP[3].PWM_CMPM = 0x0001; // enable compare event + PWM->PWM_CMP[4].PWM_CMPM = 0x0001; // enable compare event + + PWM->PWM_SCM = PWM_SCM_UPDM_MODE0 | PWM_SCM_SYNC0 | PWM_SCM_SYNC1 | PWM_SCM_SYNC2 | PWM_SCM_SYNC3 | PWM_SCM_SYNC4; // sync 1-4 with 0, use mode 0 for updates + + PWM->PWM_ENA = PWM_ENA_CHID0 | PWM_ENA_CHID1 | PWM_ENA_CHID2 | PWM_ENA_CHID3 | PWM_ENA_CHID4; // enable the channels used by G2 + PWM->PWM_IER1 = PWM_IER1_CHID0 | PWM_IER1_CHID1 | PWM_IER1_CHID2 | PWM_IER1_CHID3 | PWM_IER1_CHID4; // enable interrupts for the channels used by G2 + + NVIC_EnableIRQ(PWM_IRQn); // Enable interrupt handler + NVIC_SetPriority(PWM_IRQn, NVIC_EncodePriority(0, 10, 0)); // normal priority for PWM module (can stand some jitter on the Vref signals) +} + +void Stepper::digipot_current(const uint8_t driver, const int16_t current) { + + if (!(PWM->PWM_CH_NUM[0].PWM_CPRD == PWM_PERIOD_US)) digipot_init(); // Init PWM system if needed + + switch (driver) { + case 0: PWM->PWM_CMP[1].PWM_CMPVUPD = 0x010000000LL | G2_VREF_COUNT(G2_VREF(current)); // update X & Y + PWM->PWM_CMP[2].PWM_CMPVUPD = 0x010000000LL | G2_VREF_COUNT(G2_VREF(current)); + PWM->PWM_CMP[1].PWM_CMPMUPD = 0x0001; // enable compare event + PWM->PWM_CMP[2].PWM_CMPMUPD = 0x0001; // enable compare event + PWM->PWM_SCUC = PWM_SCUC_UPDULOCK; // tell the PWM controller to update the values on the next cycle + break; + case 1: PWM->PWM_CMP[3].PWM_CMPVUPD = 0x010000000LL | G2_VREF_COUNT(G2_VREF(current)); // update Z + PWM->PWM_CMP[3].PWM_CMPMUPD = 0x0001; // enable compare event + PWM->PWM_SCUC = PWM_SCUC_UPDULOCK; // tell the PWM controller to update the values on the next cycle + break; + default:PWM->PWM_CMP[4].PWM_CMPVUPD = 0x010000000LL | G2_VREF_COUNT(G2_VREF(current)); // update E + PWM->PWM_CMP[4].PWM_CMPMUPD = 0x0001; // enable compare event + PWM->PWM_SCUC = PWM_SCUC_UPDULOCK; // tell the PWM controller to update the values on the next cycle + break; + } +} + +volatile uint32_t PWM_ISR1_STATUS, PWM_ISR2_STATUS; + +void PWM_Handler() { + PWM_ISR1_STATUS = PWM->PWM_ISR1; + PWM_ISR2_STATUS = PWM->PWM_ISR2; + if (PWM_ISR1_STATUS & PWM_IER1_CHID0) { // CHAN_0 interrupt + *ISR_table[0].set_register = ISR_table[0].write_mask; // set X to active + *ISR_table[1].set_register = ISR_table[1].write_mask; // set Y to active + *ISR_table[2].set_register = ISR_table[2].write_mask; // set Z to active + *ISR_table[3].set_register = ISR_table[3].write_mask; // set E to active + } + else { + if (PWM_ISR2_STATUS & PWM_IER2_CMPM1) *ISR_table[0].clr_register = ISR_table[0].write_mask; // set X to inactive + if (PWM_ISR2_STATUS & PWM_IER2_CMPM2) *ISR_table[1].clr_register = ISR_table[1].write_mask; // set Y to inactive + if (PWM_ISR2_STATUS & PWM_IER2_CMPM3) *ISR_table[2].clr_register = ISR_table[2].write_mask; // set Z to inactive + if (PWM_ISR2_STATUS & PWM_IER2_CMPM4) *ISR_table[3].clr_register = ISR_table[3].write_mask; // set E to inactive + } + return; +} + +#endif // PRINTRBOARD_G2 diff --git a/Marlin/src/HAL/HAL_DUE/G2_PWM.h b/Marlin/src/HAL/HAL_DUE/G2_PWM.h new file mode 100644 index 0000000000..5cbeaceba9 --- /dev/null +++ b/Marlin/src/HAL/HAL_DUE/G2_PWM.h @@ -0,0 +1,77 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/** + * This module is stripped down version of the LPC1768_PWM.h file from + * PR #7500. It is hardwired for the PRINTRBOARD_G2 Motor Current needs. + */ + +#include "../../inc/MarlinConfigPre.h" +#include "../../module/stepper.h" +//C:\Users\bobku\Documents\GitHub\Marlin-Bob-2\Marlin\src\module\stepper.h +//C:\Users\bobku\Documents\GitHub\Marlin-Bob-2\Marlin\src\HAL\HAL_DUE\G2_PWM.h + +#define PWM_PERIOD_US 100 // base repetition rate in micro seconds + +typedef struct { // holds the data needed by the ISR to control the Vref pin + volatile uint32_t* set_register; + volatile uint32_t* clr_register; + uint32_t write_mask; +} PWM_map; + +#define G2_VREF(I) (uint32_t)(I * 5 * 0.15) // desired Vref * 1000 (scaled so don't loose accuracy in next step) + +#define G2_VREF_COUNT(Q) (uint32_t)map(constrain(Q, 500, 3.3 * 1000), 0, 3.3 * 1000, 0, PWM_PERIOD_US) // under 500 the results are very non-linear + +extern volatile uint32_t *SODR_A, *SODR_B, *CODR_A, *CODR_B; + +#define _PIN(IO) (DIO ## IO ## _PIN) + +#define PWM_MAP_INIT_ROW(IO,ZZ) { ZZ == 'A' ? SODR_A : SODR_B, ZZ == 'A' ? CODR_A : CODR_B, 1 << _PIN(IO) } + + +#define PWM_MAP_INIT { PWM_MAP_INIT_ROW(MOTOR_CURRENT_PWM_X_PIN, 'B'), \ + PWM_MAP_INIT_ROW(MOTOR_CURRENT_PWM_Y_PIN, 'B'), \ + PWM_MAP_INIT_ROW(MOTOR_CURRENT_PWM_Z_PIN, 'B'), \ + PWM_MAP_INIT_ROW(MOTOR_CURRENT_PWM_E_PIN, 'A'), \ + }; + +#define NUM_PWMS 4 + +extern PWM_map ISR_table[NUM_PWMS]; + +extern uint32_t motor_current_setting[3]; + +#define IR_BIT(p) (WITHIN(p, 0, 3) ? (p) : (p) + 4) +#define COPY_ACTIVE_TABLE() do{ for (uint8_t i = 0; i < 6 ; i++) work_table[i] = active_table[i]; }while(0) + +#define PWM_MR0 19999 // base repetition rate minus one count - 20mS +#define PWM_PR 24 // prescaler value - prescaler divide by 24 + 1 - 1 MHz output +#define PWM_PCLKSEL0 0x00 // select clock source for prescaler - defaults to 25MHz on power up + // 0: 25MHz, 1: 100MHz, 2: 50MHz, 3: 12.5MHZ to PWM1 prescaler +#define MR0_MARGIN 200 // if channel value too close to MR0 the system locks up + +extern bool PWM_table_swap; // flag to tell the ISR that the tables have been swapped + +#define HAL_G2_PWM_ISR void PWM_Handler() + +extern volatile uint32_t PWM_ISR1_STATUS, PWM_ISR2_STATUS; diff --git a/Marlin/src/HAL/HAL_DUE/G2_pins.h b/Marlin/src/HAL/HAL_DUE/G2_pins.h new file mode 100644 index 0000000000..a7f432846e --- /dev/null +++ b/Marlin/src/HAL/HAL_DUE/G2_pins.h @@ -0,0 +1,278 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#include + +/** + * This file contains the custom port/pin definitions for the PRINTRBOARD_G2 + * motherboard. This motherboard uses the SAM3X8C which is a subset of the + * SAM3X8E used in the DUE board. It uses port/pin pairs that are not + * available using the DUE definitions. + * + * The first part is a copy of the pin descriptions in the + * "variants\arduino_due_x\variant.cpp" file but with pins 34-41 replaced by + * the G2 pins. + * + * The second part is the FASTIO port/pin definitions. + * + * THESE PINS CAN ONLY BE ACCESSED VIA FASTIO COMMANDS. + */ + +/* + Copyright (c) 2011 Arduino. All right reserved. + + This library is free software; you can redistribute it and/or + modify it under the terms of the GNU Lesser General Public + License as published by the Free Software Foundation; either + version 2.1 of the License, or (at your option) any later version. + + This library is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. + See the GNU Lesser General Public License for more details. + + You should have received a copy of the GNU Lesser General Public + License along with this library; if not, write to the Free Software + Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +*/ + +typedef struct _G2_PinDescription { + Pio* pPort; + uint32_t ulPin; + uint32_t ulPeripheralId; + EPioType ulPinType; + uint32_t ulPinConfiguration; + uint32_t ulPinAttribute; + EAnalogChannel ulAnalogChannel; /* Analog pin in the Arduino context (label on the board) */ + EAnalogChannel ulADCChannelNumber; /* ADC Channel number in the SAM device */ + EPWMChannel ulPWMChannel; + ETCChannel ulTCChannel; +} G2_PinDescription; + +/** + * This section is a copy of the pin descriptions in the "variants\arduino_due_x\variant.cpp" file + * with pins 34-41 replaced by the G2 pins. + */ + +/** + * Pins descriptions + */ +const G2_PinDescription G2_g_APinDescription[] = { + // 0 .. 53 - Digital pins + // ---------------------- + // 0/1 - UART (Serial) + { PIOA, PIO_PA8A_URXD, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // URXD + { PIOA, PIO_PA9A_UTXD, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // UTXD + + // 2 + { PIOB, PIO_PB25B_TIOA0, ID_PIOB, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_TIMER), NO_ADC, NO_ADC, NOT_ON_PWM, TC0_CHA0 }, // TIOA0 + { PIOC, PIO_PC28B_TIOA7, ID_PIOC, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_TIMER), NO_ADC, NO_ADC, NOT_ON_PWM, TC2_CHA7 }, // TIOA7 + { PIOC, PIO_PC26B_TIOB6, ID_PIOC, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_TIMER), NO_ADC, NO_ADC, NOT_ON_PWM, TC2_CHB6 }, // TIOB6 + + // 5 + { PIOC, PIO_PC25B_TIOA6, ID_PIOC, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_TIMER), NO_ADC, NO_ADC, NOT_ON_PWM, TC2_CHA6 }, // TIOA6 + { PIOC, PIO_PC24B_PWML7, ID_PIOC, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_PWM), NO_ADC, NO_ADC, PWM_CH7, NOT_ON_TIMER }, // PWML7 + { PIOC, PIO_PC23B_PWML6, ID_PIOC, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_PWM), NO_ADC, NO_ADC, PWM_CH6, NOT_ON_TIMER }, // PWML6 + { PIOC, PIO_PC22B_PWML5, ID_PIOC, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_PWM), NO_ADC, NO_ADC, PWM_CH5, NOT_ON_TIMER }, // PWML5 + { PIOC, PIO_PC21B_PWML4, ID_PIOC, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_PWM), NO_ADC, NO_ADC, PWM_CH4, NOT_ON_TIMER }, // PWML4 + // 10 + { PIOC, PIO_PC29B_TIOB7, ID_PIOC, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_TIMER), NO_ADC, NO_ADC, NOT_ON_PWM, TC2_CHB7 }, // TIOB7 + { PIOD, PIO_PD7B_TIOA8, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_TIMER), NO_ADC, NO_ADC, NOT_ON_PWM, TC2_CHA8 }, // TIOA8 + { PIOD, PIO_PD8B_TIOB8, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_TIMER), NO_ADC, NO_ADC, NOT_ON_PWM, TC2_CHB8 }, // TIOB8 + + // 13 - AMBER LED + { PIOB, PIO_PB27B_TIOB0, ID_PIOB, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_TIMER), NO_ADC, NO_ADC, NOT_ON_PWM, TC0_CHB0 }, // TIOB0 + + // 14/15 - USART3 (Serial3) + { PIOD, PIO_PD4B_TXD3, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // TXD3 + { PIOD, PIO_PD5B_RXD3, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // RXD3 + + // 16/17 - USART1 (Serial2) + { PIOA, PIO_PA13A_TXD1, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // TXD1 + { PIOA, PIO_PA12A_RXD1, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // RXD1 + + // 18/19 - USART0 (Serial1) + { PIOA, PIO_PA11A_TXD0, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // TXD0 + { PIOA, PIO_PA10A_RXD0, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // RXD0 + + // 20/21 - TWI1 + { PIOB, PIO_PB12A_TWD1, ID_PIOB, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // TWD1 - SDA0 + { PIOB, PIO_PB13A_TWCK1, ID_PIOB, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // TWCK1 - SCL0 + + // 22 + { PIOB, PIO_PB26, ID_PIOB, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 22 + { PIOA, PIO_PA14, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 23 + { PIOA, PIO_PA15, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 24 + { PIOD, PIO_PD0, ID_PIOD, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 25 + + // 26 + { PIOD, PIO_PD1, ID_PIOD, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 26 + { PIOD, PIO_PD2, ID_PIOD, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 27 + { PIOD, PIO_PD3, ID_PIOD, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 28 + { PIOD, PIO_PD6, ID_PIOD, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 29 + + // 30 + { PIOD, PIO_PD9, ID_PIOD, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 30 + { PIOA, PIO_PA7, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 31 + { PIOD, PIO_PD10, ID_PIOD, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 32 + { PIOC, PIO_PC1, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 33 + + // 34 + + // start of custom pins + { PIOA, PIO_PA29, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 34 Y_STEP_PIN + { PIOB, PIO_PB1, ID_PIOB, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 35 Y_DIR_PIN + { PIOB, PIO_PB0, ID_PIOB, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 36 Y_ENABLE_PIN + { PIOB, PIO_PB22, ID_PIOB, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 37 E0_ENABLE_PIN + { PIOB, PIO_PB11, ID_PIOB, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 38 E0_MS1_PIN + { PIOB, PIO_PB10, ID_PIOB, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 39 E0_MS3_PIN + { PIOA, PIO_PA5, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 40 HEATER_0_PIN + { PIOB, PIO_PB24, ID_PIOB, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 41 HEATER_BED_PIN + // end of custom pins + + // 42 + { PIOA, PIO_PA19, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 42 + { PIOA, PIO_PA20, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 43 + { PIOC, PIO_PC19, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 44 + { PIOC, PIO_PC18, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 45 + + // 46 + { PIOC, PIO_PC17, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 46 + { PIOC, PIO_PC16, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 47 + { PIOC, PIO_PC15, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 48 + { PIOC, PIO_PC14, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 49 + + // 50 + { PIOC, PIO_PC13, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 50 + { PIOC, PIO_PC12, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 51 + { PIOB, PIO_PB21, ID_PIOB, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 52 + { PIOB, PIO_PB14, ID_PIOB, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 53 + + + // 54 .. 65 - Analog pins + // ---------------------- + { PIOA, PIO_PA16X1_AD7, ID_PIOA, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC0, ADC7, NOT_ON_PWM, NOT_ON_TIMER }, // AD0 + { PIOA, PIO_PA24X1_AD6, ID_PIOA, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC1, ADC6, NOT_ON_PWM, NOT_ON_TIMER }, // AD1 + { PIOA, PIO_PA23X1_AD5, ID_PIOA, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC2, ADC5, NOT_ON_PWM, NOT_ON_TIMER }, // AD2 + { PIOA, PIO_PA22X1_AD4, ID_PIOA, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC3, ADC4, NOT_ON_PWM, NOT_ON_TIMER }, // AD3 + // 58 + { PIOA, PIO_PA6X1_AD3, ID_PIOA, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC4, ADC3, NOT_ON_PWM, TC0_CHB2 }, // AD4 + { PIOA, PIO_PA4X1_AD2, ID_PIOA, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC5, ADC2, NOT_ON_PWM, NOT_ON_TIMER }, // AD5 + { PIOA, PIO_PA3X1_AD1, ID_PIOA, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC6, ADC1, NOT_ON_PWM, TC0_CHB1 }, // AD6 + { PIOA, PIO_PA2X1_AD0, ID_PIOA, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC7, ADC0, NOT_ON_PWM, TC0_CHA1 }, // AD7 + // 62 + { PIOB, PIO_PB17X1_AD10, ID_PIOB, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC8, ADC10, NOT_ON_PWM, NOT_ON_TIMER }, // AD8 + { PIOB, PIO_PB18X1_AD11, ID_PIOB, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC9, ADC11, NOT_ON_PWM, NOT_ON_TIMER }, // AD9 + { PIOB, PIO_PB19X1_AD12, ID_PIOB, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC10, ADC12, NOT_ON_PWM, NOT_ON_TIMER }, // AD10 + { PIOB, PIO_PB20X1_AD13, ID_PIOB, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC11, ADC13, NOT_ON_PWM, NOT_ON_TIMER }, // AD11 + + // 66/67 - DAC0/DAC1 + { PIOB, PIO_PB15X1_DAC0, ID_PIOB, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC12, DA0, NOT_ON_PWM, NOT_ON_TIMER }, // DAC0 + { PIOB, PIO_PB16X1_DAC1, ID_PIOB, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC13, DA1, NOT_ON_PWM, NOT_ON_TIMER }, // DAC1 + + // 68/69 - CANRX0/CANTX0 + { PIOA, PIO_PA1A_CANRX0, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, ADC14, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // CANRX + { PIOA, PIO_PA0A_CANTX0, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, ADC15, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // CANTX + + // 70/71 - TWI0 + { PIOA, PIO_PA17A_TWD0, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // TWD0 - SDA1 + { PIOA, PIO_PA18A_TWCK0, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // TWCK0 - SCL1 + + // 72/73 - LEDs + { PIOC, PIO_PC30, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // LED AMBER RXL + { PIOA, PIO_PA21, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // LED AMBER TXL + + // 74/75/76 - SPI + { PIOA, PIO_PA25A_SPI0_MISO,ID_PIOA,PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // MISO + { PIOA, PIO_PA26A_SPI0_MOSI,ID_PIOA,PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // MOSI + { PIOA, PIO_PA27A_SPI0_SPCK,ID_PIOA,PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // SPCK + + // 77 - SPI CS0 + { PIOA, PIO_PA28A_SPI0_NPCS0,ID_PIOA,PIO_PERIPH_A,PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // NPCS0 + + // 78 - SPI CS3 (unconnected) + { PIOB, PIO_PB23B_SPI0_NPCS3,ID_PIOB,PIO_PERIPH_B,PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // NPCS3 + + // 79 .. 84 - "All pins" masks + + // 79 - TWI0 all pins + { PIOA, PIO_PA17A_TWD0|PIO_PA18A_TWCK0, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_COMBO), NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, + // 80 - TWI1 all pins + { PIOB, PIO_PB12A_TWD1|PIO_PB13A_TWCK1, ID_PIOB, PIO_PERIPH_A, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_COMBO), NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, + // 81 - UART (Serial) all pins + { PIOA, PIO_PA8A_URXD|PIO_PA9A_UTXD, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_COMBO), NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, + // 82 - USART0 (Serial1) all pins + { PIOA, PIO_PA11A_TXD0|PIO_PA10A_RXD0, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_COMBO), NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, + // 83 - USART1 (Serial2) all pins + { PIOA, PIO_PA13A_TXD1|PIO_PA12A_RXD1, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_COMBO), NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, + // 84 - USART3 (Serial3) all pins + { PIOD, PIO_PD4B_TXD3|PIO_PD5B_RXD3, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_COMBO), NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, + + // 85 - USB + { PIOB, PIO_PB11A_UOTGID|PIO_PB10A_UOTGVBOF, ID_PIOB, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL,NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // ID - VBOF + + // 86 - SPI CS2 + { PIOB, PIO_PB21B_SPI0_NPCS2, ID_PIOB, PIO_PERIPH_B, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // NPCS2 + + // 87 - SPI CS1 + { PIOA, PIO_PA29A_SPI0_NPCS1, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // NPCS1 + + // 88/89 - CANRX1/CANTX1 (same physical pin for 66/53) + { PIOB, PIO_PB15A_CANRX1, ID_PIOB, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // CANRX1 + { PIOB, PIO_PB14A_CANTX1, ID_PIOB, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // CANTX1 + + // 90 .. 91 - "All CAN pins" masks + // 90 - CAN0 all pins + { PIOA, PIO_PA1A_CANRX0|PIO_PA0A_CANTX0, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_COMBO), NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, + // 91 - CAN1 all pins + { PIOB, PIO_PB15A_CANRX1|PIO_PB14A_CANTX1, ID_PIOB, PIO_PERIPH_A, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_COMBO), NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, + + // END + { NULL, 0, 0, PIO_NOT_A_PIN, PIO_DEFAULT, 0, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER } +}; + +// This section replaces the FASTIO definitions of pins 34-41 + +#define DIO34_PIN 29 +#define DIO34_WPORT PIOA // only available via FASTIO // 34 PA29 - Y_STEP_PIN + +#define DIO35_PIN 1 +#define DIO35_WPORT PIOB // only available via FASTIO // 35 PAB1 - Y_DIR_PIN + +#define DIO36_PIN 0 +#define DIO36_WPORT PIOB // only available via FASTIO // 36 PB0 - Y_ENABLE_PIN + +#define DIO37_PIN 22 +#define DIO37_WPORT PIOB // only available via FASTIO // 37 PB22 - E0_ENABLE_PIN + +#define DIO38_PIN 11 +#define DIO38_WPORT PIOB // only available via FASTIO // 38 PB11 - E0_MS1_PIN + +#define DIO39_PIN 10 +#define DIO39_WPORT PIOB // only available via FASTIO // 39 PB10 - E0_MS3_PIN + +#define DIO40_PIN 5 +#define DIO40_WPORT PIOA // only available via FASTIO // 40 PA5 - HEATER_0_PIN + +#define DIO41_PIN 24 +#define DIO41_WPORT PIOB // only available via FASTIO // 41 PB24 - HEATER_BED_PIN diff --git a/Marlin/src/HAL/HAL_DUE/fastio_Due.h b/Marlin/src/HAL/HAL_DUE/fastio_Due.h index 18bf55e6c2..02c1a1c5d6 100644 --- a/Marlin/src/HAL/HAL_DUE/fastio_Due.h +++ b/Marlin/src/HAL/HAL_DUE/fastio_Due.h @@ -65,7 +65,7 @@ // Write to a pin #define _WRITE_VAR(IO,V) do { \ volatile Pio* port = digitalPinToPort(IO); \ - uint32_t mask = digitalPinToBitMask(IO); \ + const uint32_t mask = digitalPinToBitMask(IO); \ if (V) port->PIO_SODR = mask; \ else port->PIO_CODR = mask; \ } while(0) @@ -73,7 +73,7 @@ // Write to a pin #define _WRITE(IO,V) do { \ volatile Pio* port = (DIO ## IO ## _WPORT); \ - uint32_t mask = MASK(DIO ## IO ## _PIN); \ + const uint32_t mask = MASK(DIO ## IO ## _PIN); \ if (V) port->PIO_SODR = mask; \ else port->PIO_CODR = mask; \ } while(0) @@ -81,18 +81,79 @@ // Toggle a pin #define _TOGGLE(IO) _WRITE(IO, !READ(IO)) -// Set pin as input -#define _SET_INPUT(IO) do{ \ - pmc_enable_periph_clk(g_APinDescription[IO].ulPeripheralId); \ - PIO_Configure(digitalPinToPort(IO), PIO_INPUT, digitalPinToBitMask(IO), 0); \ -}while(0) +#include -// Set pin as output -#define _SET_OUTPUT(IO) do{ \ - pmc_enable_periph_clk(g_APinDescription[IO].ulPeripheralId); \ - PIO_Configure(digitalPinToPort(IO), _READ(IO) ? PIO_OUTPUT_1 : PIO_OUTPUT_0, digitalPinToBitMask(IO), g_APinDescription[IO].ulPinConfiguration); \ - g_pinStatus[IO] = (g_pinStatus[IO] & 0xF0) | PIN_STATUS_DIGITAL_OUTPUT;\ -}while(0) +#if MB(PRINTRBOARD_G2) + + #include "G2_pins.h" + + // Set pin as input + #define _SET_INPUT(IO) do{ \ + pmc_enable_periph_clk(G2_g_APinDescription[IO].ulPeripheralId); \ + PIO_Configure((DIO ## IO ## _WPORT), PIO_INPUT, MASK(DIO ## IO ## _PIN), 0); \ + }while(0) + + // Set pin as output + #define _SET_OUTPUT(IO) do{ \ + uint32_t mask = MASK(G2_g_APinDescription[IO].ulPeripheralId); \ + if ((PMC->PMC_PCSR0 & mask) != (mask)) PMC->PMC_PCER0 = mask; \ + volatile Pio* port = (DIO ## IO ## _WPORT); \ + mask = MASK(DIO ## IO ## _PIN); \ + if (_READ(IO)) port->PIO_SODR = mask; \ + else port->PIO_CODR = mask; \ + port->PIO_IDR = mask; \ + const uint32_t pin_config = G2_g_APinDescription[IO].ulPinConfiguration; \ + if (pin_config & PIO_PULLUP) port->PIO_PUER = mask; \ + else port->PIO_PUDR = mask; \ + if (pin_config & PIO_OPENDRAIN) port->PIO_MDER = mask; \ + else port->PIO_MDDR = mask; \ + port->PIO_PER = mask; \ + port->PIO_OER = mask; \ + g_pinStatus[IO] = (g_pinStatus[IO] & 0xF0) | PIN_STATUS_DIGITAL_OUTPUT; \ + }while(0) + + /** + * Set pin as output with comments + * #define _SET_OUTPUT(IO) do{ \ + * uint32_t mask = MASK(G2_g_APinDescription[IO].ulPeripheralId); \ + * if ((PMC->PMC_PCSR0 & mask ) != (mask)) PMC->PMC_PCER0 = mask; \ // enable PIO clock if not already enabled + * + * volatile Pio* port = (DIO ## IO ## _WPORT); \ + * const uint32_t mask = MASK(DIO ## IO ## _PIN); \ + * if (_READ(IO)) port->PIO_SODR = mask; \ // set output to match input BEFORE setting direction or will glitch the output + * else port->PIO_CODR = mask; \ + * + * port->PIO_IDR = mask; \ // disable interrupt + * + * uint32_t pin_config = G2_g_APinDescription[IO].ulPinConfiguration; \ + * if (pin_config & PIO_PULLUP) pPio->PIO_PUER = mask; \ // enable pullup if necessary + * else pPio->PIO_PUDR = mask; \ + * + * if (pin_config & PIO_OPENDRAIN) port->PIO_MDER = mask; \ // Enable multi-drive if necessary + * else port->PIO_MDDR = mask; \ + * + * port->PIO_PER = mask; \ + * port->PIO_OER = mask; \ // set to output + * + * g_pinStatus[IO] = (g_pinStatus[IO] & 0xF0) | PIN_STATUS_DIGITAL_OUTPUT; \ + * }while(0) + */ + +#else + + // Set pin as input + #define _SET_INPUT(IO) do{ \ + pmc_enable_periph_clk(g_APinDescription[IO].ulPeripheralId); \ + PIO_Configure(digitalPinToPort(IO), PIO_INPUT, digitalPinToBitMask(IO), 0); \ + }while(0) + + // Set pin as output + #define _SET_OUTPUT(IO) do{ \ + pmc_enable_periph_clk(g_APinDescription[IO].ulPeripheralId); \ + PIO_Configure(digitalPinToPort(IO), _READ(IO) ? PIO_OUTPUT_1 : PIO_OUTPUT_0, digitalPinToBitMask(IO), g_APinDescription[IO].ulPinConfiguration); \ + g_pinStatus[IO] = (g_pinStatus[IO] & 0xF0) | PIN_STATUS_DIGITAL_OUTPUT; \ + }while(0) +#endif // Set pin as input with pullup mode #define _PULLUP(IO,V) pinMode(IO, (V) ? INPUT_PULLUP : INPUT) @@ -243,29 +304,33 @@ #define DIO33_PIN 1 #define DIO33_WPORT PIOC -#define DIO34_PIN 2 -#define DIO34_WPORT PIOC +#if !MB(PRINTRBOARD_G2) // normal DUE pin mapping -#define DIO35_PIN 3 -#define DIO35_WPORT PIOC + #define DIO34_PIN 2 + #define DIO34_WPORT PIOC -#define DIO36_PIN 4 -#define DIO36_WPORT PIOC + #define DIO35_PIN 3 + #define DIO35_WPORT PIOC -#define DIO37_PIN 5 -#define DIO37_WPORT PIOC + #define DIO36_PIN 4 + #define DIO36_WPORT PIOC -#define DIO38_PIN 6 -#define DIO38_WPORT PIOC + #define DIO37_PIN 5 + #define DIO37_WPORT PIOC -#define DIO39_PIN 7 -#define DIO39_WPORT PIOC + #define DIO38_PIN 6 + #define DIO38_WPORT PIOC -#define DIO40_PIN 8 -#define DIO40_WPORT PIOC + #define DIO39_PIN 7 + #define DIO39_WPORT PIOC -#define DIO41_PIN 9 -#define DIO41_WPORT PIOC + #define DIO40_PIN 8 + #define DIO40_WPORT PIOC + + #define DIO41_PIN 9 + #define DIO41_WPORT PIOC + +#endif // !PRINTRBOARD_G2 #define DIO42_PIN 19 #define DIO42_WPORT PIOA @@ -418,6 +483,7 @@ #define DIO91_WPORT PIOB #if ARDUINO_SAM_ARCHIM + #define DIO92_PIN 11 #define DIO92_WPORT PIOC @@ -468,7 +534,9 @@ #define DIO108_PIN 9 #define DIO108_WPORT PIOB -#else + +#else // !ARDUINO_SAM_ARCHIM + #define DIO92_PIN 5 #define DIO92_WPORT PIOA @@ -495,4 +563,5 @@ #define DIO100_PIN 11 #define DIO100_WPORT PIOC -#endif + +#endif // !ARDUINO_SAM_ARCHIM diff --git a/Marlin/src/Marlin.cpp b/Marlin/src/Marlin.cpp index b8aaa4cfb5..d81d96eb64 100644 --- a/Marlin/src/Marlin.cpp +++ b/Marlin/src/Marlin.cpp @@ -423,7 +423,9 @@ void disable_all_steppers() { * - Check for HOME button held down * - Check if cooling fan needs to be switched on * - Check if an idle but hot extruder needs filament extruded (EXTRUDER_RUNOUT_PREVENT) + * - Pulse FET_SAFETY_PIN if it exists */ + void manage_inactivity(const bool ignore_stepper_queue/*=false*/) { #if HAS_FILAMENT_SENSOR @@ -639,6 +641,16 @@ void manage_inactivity(const bool ignore_stepper_queue/*=false*/) { planner.check_axes_activity(); next_check_axes_ms = ms + 100UL; } + + #if PIN_EXISTS(FET_SAFETY) + static millis_t FET_next; + if (ELAPSED(ms, FET_next)) { + FET_next = ms + FET_SAFETY_DELAY; // 2uS pulse every FET_SAFETY_DELAY mS + OUT_WRITE(FET_SAFETY_PIN, !FET_SAFETY_INVERTED); + DELAY_US(2); + WRITE(FET_SAFETY_PIN, FET_SAFETY_INVERTED); + } + #endif } /** diff --git a/Marlin/src/config/examples/Printrbot/PrintrboardG2/Configuration.h b/Marlin/src/config/examples/Printrbot/PrintrboardG2/Configuration.h new file mode 100644 index 0000000000..62a6ead22d --- /dev/null +++ b/Marlin/src/config/examples/Printrbot/PrintrboardG2/Configuration.h @@ -0,0 +1,2102 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration.h + * + * Basic settings such as: + * + * - Type of electronics + * - Type of temperature sensor + * - Printer geometry + * - Endstop configuration + * - LCD controller + * - Extra features + * + * Advanced settings can be found in Configuration_adv.h + * + */ +#define CONFIGURATION_H_VERSION 020000 + +//=========================================================================== +//============================= Getting Started ============================= +//=========================================================================== + +/** + * Here are some standard links for getting your machine calibrated: + * + * http://reprap.org/wiki/Calibration + * http://youtu.be/wAL9d7FgInk + * http://calculator.josefprusa.cz + * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide + * http://www.thingiverse.com/thing:5573 + * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap + * http://www.thingiverse.com/thing:298812 + */ + +//=========================================================================== +//============================= DELTA Printer =============================== +//=========================================================================== +// For a Delta printer start with one of the configuration files in the +// config/examples/delta directory and customize for your machine. +// + +//=========================================================================== +//============================= SCARA Printer =============================== +//=========================================================================== +// For a SCARA printer start with the configuration files in +// config/examples/SCARA and customize for your machine. +// + +// @section info + +// User-specified version info of this build to display in [Pronterface, etc] terminal window during +// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this +// build by the user have been successfully uploaded into firmware. +#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. +#define SHOW_BOOTSCREEN +#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1 +#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2 + +/** + * *** VENDORS PLEASE READ *** + * + * Marlin allows you to add a custom boot image for Graphical LCDs. + * With this option Marlin will first show your custom screen followed + * by the standard Marlin logo with version number and web URL. + * + * We encourage you to take advantage of this new feature and we also + * respectfully request that you retain the unmodified Marlin boot screen. + */ + +// Enable to show the bitmap in Marlin/_Bootscreen.h on startup. +//#define SHOW_CUSTOM_BOOTSCREEN + +// Enable to show the bitmap in Marlin/_Statusscreen.h on the status screen. +//#define CUSTOM_STATUS_SCREEN_IMAGE + +// @section machine + +/** + * Select the serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +#define SERIAL_PORT 0 + +/** + * Select a secondary serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +// For programming port do NOT define +#define SERIAL_PORT_2 0 // For native port + +/** + * This setting determines the communication speed of the printer. + * + * 250000 works in most cases, but you might try a lower speed if + * you commonly experience drop-outs during host printing. + * You may try up to 1000000 to speed up SD file transfer. + * + * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] + */ +#define BAUDRATE 115200 + +// Enable the Bluetooth serial interface on AT90USB devices +//#define BLUETOOTH + +// The following define selects which electronics board you have. +// Please choose the name from boards.h that matches your setup +#ifndef MOTHERBOARD + #define MOTHERBOARD BOARD_PRINTRBOARD_G2 +#endif + +// Optional custom name for your RepStrap or other custom machine +// Displayed in the LCD "Ready" message +//#define CUSTOM_MACHINE_NAME "3D Printer" + +// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) +// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" + +// @section extruder + +// This defines the number of extruders +// :[1, 2, 3, 4, 5, 6] +#define EXTRUDERS 1 + +// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc. +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0 + +// For Cyclops or any "multi-extruder" that shares a single nozzle. +//#define SINGLENOZZLE + +/** + * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants. + * + * This device allows one stepper driver on a control board to drive + * two to eight stepper motors, one at a time, in a manner suitable + * for extruders. + * + * This option only allows the multiplexer to switch on tool-change. + * Additional options to configure custom E moves are pending. + */ +//#define MK2_MULTIPLEXER +#if ENABLED(MK2_MULTIPLEXER) + // Override the default DIO selector pins here, if needed. + // Some pins files may provide defaults for these pins. + //#define E_MUX0_PIN 40 // Always Required + //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs + //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs +#endif + +/** + * Prusa Multi-Material Unit v2 + * + * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails. + * Requires EXTRUDERS = 5 + * + * For additional configuration see Configuration_adv.h + */ +//#define PRUSA_MMU2 + +// A dual extruder that uses a single stepper motor +//#define SWITCHING_EXTRUDER +#if ENABLED(SWITCHING_EXTRUDER) + #define SWITCHING_EXTRUDER_SERVO_NR 0 + #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3] + #if EXTRUDERS > 3 + #define SWITCHING_EXTRUDER_E23_SERVO_NR 1 + #endif +#endif + +// A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles +//#define SWITCHING_NOZZLE +#if ENABLED(SWITCHING_NOZZLE) + #define SWITCHING_NOZZLE_SERVO_NR 0 + //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second + #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo) +#endif + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN. + */ +//#define PARKING_EXTRUDER + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a magnetic docking mechanism using movements and no solenoid + * + * project : https://www.thingiverse.com/thing:3080893 + * movements : https://youtu.be/0xCEiG9VS3k + * https://youtu.be/Bqbcs0CU2FE + */ +//#define MAGNETIC_PARKING_EXTRUDER + +#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders + #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #if ENABLED(PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage + #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil + #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined. + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #elif ENABLED(MAGNETIC_PARKING_EXTRUDER) + + #define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point + #define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple + #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point + #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling + + #endif + +#endif + +/** + * Switching Toolhead + * + * Support for swappable and dockable toolheads, such as + * the E3D Tool Changer. Toolheads are locked with a servo. + */ +//#define SWITCHING_TOOLHEAD +#if ENABLED(SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector + #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock + #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock + #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis + #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders +#endif + +/** + * "Mixing Extruder" + * - Adds G-codes M163 and M164 to set and "commit" the current mix factors. + * - Extends the stepping routines to move multiple steppers in proportion to the mix. + * - Optional support for Repetier Firmware's 'M164 S' supporting virtual tools. + * - This implementation supports up to two mixing extruders. + * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation). + */ +//#define MIXING_EXTRUDER +#if ENABLED(MIXING_EXTRUDER) + #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder + #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164 + //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands + //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD + #if ENABLED(GRADIENT_MIX) + //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias + #endif +#endif + +// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). +// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). +// For the other hotends it is their distance from the extruder 0 hotend. +//#define HOTEND_OFFSET_X {0.0, 20.00} // (mm) relative X-offset for each nozzle +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (mm) relative Y-offset for each nozzle +//#define HOTEND_OFFSET_Z {0.0, 0.00} // (mm) relative Z-offset for each nozzle + +// @section machine + +/** + * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN + * + * 0 = No Power Switch + * 1 = ATX + * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) + * + * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' } + */ +#define POWER_SUPPLY 0 + +#if POWER_SUPPLY > 0 + // Enable this option to leave the PSU off at startup. + // Power to steppers and heaters will need to be turned on with M80. + //#define PS_DEFAULT_OFF + + //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin + #if ENABLED(AUTO_POWER_CONTROL) + #define AUTO_POWER_FANS // Turn on PSU if fans need power + #define AUTO_POWER_E_FANS + #define AUTO_POWER_CONTROLLERFAN + #define POWER_TIMEOUT 30 + #endif + +#endif + +// @section temperature + +//=========================================================================== +//============================= Thermal Settings ============================ +//=========================================================================== + +/** + * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table + * + * Temperature sensors available: + * + * -4 : thermocouple with AD8495 + * -3 : thermocouple with MAX31855 (only for sensor 0) + * -2 : thermocouple with MAX6675 (only for sensor 0) + * -1 : thermocouple with AD595 + * 0 : not used + * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 3 : Mendel-parts thermistor (4.7k pullup) + * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! + * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) + * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) + * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) + * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) + * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) + * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) + * 10 : 100k RS thermistor 198-961 (4.7k pullup) + * 11 : 100k beta 3950 1% thermistor (4.7k pullup) + * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) + * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" + * 15 : 100k thermistor calibration for JGAurora A5 hotend + * 20 : the PT100 circuit found in the Ultimainboard V2.x + * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 + * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup + * 66 : 4.7M High Temperature thermistor from Dyze Design + * 70 : the 100K thermistor found in the bq Hephestos 2 + * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor + * + * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k. + * (but gives greater accuracy and more stable PID) + * 51 : 100k thermistor - EPCOS (1k pullup) + * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup) + * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) + * + * 1047 : Pt1000 with 4k7 pullup + * 1010 : Pt1000 with 1k pullup (non standard) + * 147 : Pt100 with 4k7 pullup + * 110 : Pt100 with 1k pullup (non standard) + * + * Use these for Testing or Development purposes. NEVER for production machine. + * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. + * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. + * + * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" } + */ +#define TEMP_SENSOR_0 1 +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_3 0 +#define TEMP_SENSOR_4 0 +#define TEMP_SENSOR_5 0 +#define TEMP_SENSOR_BED 1 +#define TEMP_SENSOR_CHAMBER 0 + +// Dummy thermistor constant temperature readings, for use with 998 and 999 +#define DUMMY_THERMISTOR_998_VALUE 25 +#define DUMMY_THERMISTOR_999_VALUE 100 + +// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings +// from the two sensors differ too much the print will be aborted. +//#define TEMP_SENSOR_1_AS_REDUNDANT +#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 + +// Extruder temperature must be close to target for this long before M109 returns success +#define TEMP_RESIDENCY_TIME 10 // (seconds) +#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one +#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early. + +// Bed temperature must be close to target for this long before M190 returns success +#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) +#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one +#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early. + +// The minimal temperature defines the temperature below which the heater will not be enabled It is used +// to check that the wiring to the thermistor is not broken. +// Otherwise this would lead to the heater being powered on all the time. +#define HEATER_0_MINTEMP 5 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_3_MINTEMP 5 +#define HEATER_4_MINTEMP 5 +#define HEATER_5_MINTEMP 5 +#define BED_MINTEMP 5 + +// When temperature exceeds max temp, your heater will be switched off. +// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! +// You should use MINTEMP for thermistor short/failure protection. +#define HEATER_0_MAXTEMP 275 +#define HEATER_1_MAXTEMP 275 +#define HEATER_2_MAXTEMP 275 +#define HEATER_3_MAXTEMP 275 +#define HEATER_4_MAXTEMP 275 +#define HEATER_5_MAXTEMP 275 +#define BED_MAXTEMP 150 + +//=========================================================================== +//============================= PID Settings ================================ +//=========================================================================== +// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning + +// Comment the following line to disable PID and enable bang-bang. +#define PIDTEMP +#define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#define PID_K1 0.95 // Smoothing factor within any PID loop +#if ENABLED(PIDTEMP) + //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM) + //#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM) + //#define PID_DEBUG // Sends debug data to the serial port. + //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX + //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] + #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature + // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. + + // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it + + // Ultimaker + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 + + // MakerGear + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 + + // Mendel Parts V9 on 12V + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 + +#endif // PIDTEMP + +//=========================================================================== +//============================= PID > Bed Temperature Control =============== +//=========================================================================== + +/** + * PID Bed Heating + * + * If this option is enabled set PID constants below. + * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis. + * + * The PID frequency will be the same as the extruder PWM. + * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz, + * which is fine for driving a square wave into a resistive load and does not significantly + * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W + * heater. If your configuration is significantly different than this and you don't understand + * the issues involved, don't use bed PID until someone else verifies that your hardware works. + */ +//#define PIDTEMPBED + +//#define BED_LIMIT_SWITCHING + +/** + * Max Bed Power + * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis). + * When set to any value below 255, enables a form of PWM to the bed that acts like a divider + * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED) + */ +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +#if ENABLED(PIDTEMPBED) + + //#define PID_BED_DEBUG // Sends debug data to the serial port. + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from pidautotune + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 + + // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + +// @section extruder + +/** + * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP. + * Add M302 to set the minimum extrusion temperature and/or turn + * cold extrusion prevention on and off. + * + * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! *** + */ +//#define PREVENT_COLD_EXTRUSION +#define EXTRUDE_MINTEMP 170 + +/** + * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH. + * Note: For Bowden Extruders make this large enough to allow load/unload. + */ +#define PREVENT_LENGTHY_EXTRUDE +#define EXTRUDE_MAXLENGTH 200 + +//=========================================================================== +//======================== Thermal Runaway Protection ======================= +//=========================================================================== + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * If you get "Thermal Runaway" or "Heating failed" errors the + * details can be tuned in Configuration_adv.h + */ + +#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders +#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed + +//=========================================================================== +//============================= Mechanical Settings ========================= +//=========================================================================== + +// @section machine + +// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics +// either in the usual order or reversed +//#define COREXY +//#define COREXZ +//#define COREYZ +//#define COREYX +//#define COREZX +//#define COREZY + +//=========================================================================== +//============================== Endstop Settings =========================== +//=========================================================================== + +// @section homing + +// Specify here all the endstop connectors that are connected to any endstop or probe. +// Almost all printers will be using one per axis. Probes will use one or more of the +// extra connectors. Leave undefined any used for non-endstop and non-probe purposes. +#define USE_XMIN_PLUG +//#define USE_YMIN_PLUG +#define USE_ZMIN_PLUG +//#define USE_XMAX_PLUG +#define USE_YMAX_PLUG +//#define USE_ZMAX_PLUG + +// Enable pullup for all endstops to prevent a floating state +#define ENDSTOPPULLUPS +#if DISABLED(ENDSTOPPULLUPS) + // Disable ENDSTOPPULLUPS to set pullups individually + //#define ENDSTOPPULLUP_XMAX + //#define ENDSTOPPULLUP_YMAX + //#define ENDSTOPPULLUP_ZMAX + //#define ENDSTOPPULLUP_XMIN + //#define ENDSTOPPULLUP_YMIN + //#define ENDSTOPPULLUP_ZMIN + //#define ENDSTOPPULLUP_ZMIN_PROBE +#endif + +// Enable pulldown for all endstops to prevent a floating state +//#define ENDSTOPPULLDOWNS +#if DISABLED(ENDSTOPPULLDOWNS) + // Disable ENDSTOPPULLDOWNS to set pulldowns individually + //#define ENDSTOPPULLDOWN_XMAX + //#define ENDSTOPPULLDOWN_YMAX + //#define ENDSTOPPULLDOWN_ZMAX + //#define ENDSTOPPULLDOWN_XMIN + //#define ENDSTOPPULLDOWN_YMIN + //#define ENDSTOPPULLDOWN_ZMIN + //#define ENDSTOPPULLDOWN_ZMIN_PROBE +#endif + +// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). +#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop. +#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop. +#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop. +#define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop. +#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop. +#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop. +#define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe. + +/** + * Stepper Drivers + * + * These settings allow Marlin to tune stepper driver timing and enable advanced options for + * stepper drivers that support them. You may also override timing options in Configuration_adv.h. + * + * A4988 is assumed for unspecified drivers. + * + * Options: A4988, A5984, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100, + * TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE, + * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE, + * TMC2160, TMC2160_STANDALONE, TMC5130, TMC5130_STANDALONE, + * TMC5160, TMC5160_STANDALONE + * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE'] + */ +//#define X_DRIVER_TYPE DRV8825 +//#define Y_DRIVER_TYPE DRV8825 +//#define Z_DRIVER_TYPE DRV8825 +//#define X2_DRIVER_TYPE A4988 +//#define Y2_DRIVER_TYPE A4988 +//#define Z2_DRIVER_TYPE A4988 +//#define Z3_DRIVER_TYPE A4988 +//#define E0_DRIVER_TYPE DRV8825 +//#define E1_DRIVER_TYPE A4988 +//#define E2_DRIVER_TYPE A4988 +//#define E3_DRIVER_TYPE A4988 +//#define E4_DRIVER_TYPE A4988 +//#define E5_DRIVER_TYPE A4988 + +// Enable this feature if all enabled endstop pins are interrupt-capable. +// This will remove the need to poll the interrupt pins, saving many CPU cycles. +//#define ENDSTOP_INTERRUPTS_FEATURE + +/** + * Endstop Noise Threshold + * + * Enable if your probe or endstops falsely trigger due to noise. + * + * - Higher values may affect repeatability or accuracy of some bed probes. + * - To fix noise install a 100nF ceramic capacitor inline with the switch. + * - This feature is not required for common micro-switches mounted on PCBs + * based on the Makerbot design, which already have the 100nF capacitor. + * + * :[2,3,4,5,6,7] + */ +//#define ENDSTOP_NOISE_THRESHOLD 2 + +//============================================================================= +//============================== Movement Settings ============================ +//============================================================================= +// @section motion + +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * With this option each E stepper can have its own factors for the + * following movement settings. If fewer factors are given than the + * total number of extruders, the last value applies to the rest. + */ +//#define DISTINCT_E_FACTORS + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +//#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 } +#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 80, 80 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +//#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 } +#define DEFAULT_MAX_FEEDRATE { 30, 30,30,30 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * (Maximum start speed for accelerated moves) + * Override with M201 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +//#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 } +#define DEFAULT_MAX_ACCELERATION { 100, 100, 100, 100 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +//#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves +//#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts +//#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves + +#define DEFAULT_ACCELERATION 100 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 100 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 100 // X, Y, Z acceleration for travel (non printing) moves + +// +// Use Junction Deviation instead of traditional Jerk Limiting +// +//#define JUNCTION_DEVIATION +#if ENABLED(JUNCTION_DEVIATION) + #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge +#endif + +/** + * Default Jerk (mm/s) + * Override with M205 X Y Z E + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#if DISABLED(JUNCTION_DEVIATION) + #define DEFAULT_XJERK 1.0 + #define DEFAULT_YJERK 1.0 + #define DEFAULT_ZJERK 0.3 +#endif + +#define DEFAULT_EJERK 5.0 // May be used by Linear Advance + +/** + * S-Curve Acceleration + * + * This option eliminates vibration during printing by fitting a Bézier + * curve to move acceleration, producing much smoother direction changes. + * + * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained + */ +//#define S_CURVE_ACCELERATION + +//=========================================================================== +//============================= Z Probe Options ============================= +//=========================================================================== +// @section probes + +// +// See http://marlinfw.org/docs/configuration/probes.html +// + +/** + * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + * + * Enable this option for a probe connected to the Z Min endstop pin. + */ +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +/** + * Z_MIN_PROBE_ENDSTOP + * + * Enable this option for a probe connected to any pin except Z-Min. + * (By default Marlin assumes the Z-Max endstop pin.) + * To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below. + * + * - The simplest option is to use a free endstop connector. + * - Use 5V for powered (usually inductive) sensors. + * + * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin: + * - For simple switches connect... + * - normally-closed switches to GND and D32. + * - normally-open switches to 5V and D32. + * + * WARNING: Setting the wrong pin may have unexpected and potentially + * disastrous consequences. Use with caution and do your homework. + * + */ +//#define Z_MIN_PROBE_ENDSTOP + +/** + * Probe Type + * + * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. + * Activate one of these to use Auto Bed Leveling below. + */ + +/** + * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe. + * Use G29 repeatedly, adjusting the Z height at each point with movement commands + * or (with LCD_BED_LEVELING) the LCD controller. + */ +//#define PROBE_MANUALLY +//#define MANUAL_PROBE_START_Z 0.2 + +/** + * A Fix-Mounted Probe either doesn't deploy or needs manual deployment. + * (e.g., an inductive probe or a nozzle-based probe-switch.) + */ +//#define FIX_MOUNTED_PROBE + +/** + * Z Servo Probe, such as an endstop switch on a rotating arm. + */ +//#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector. +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +/** + * The BLTouch probe uses a Hall effect sensor and emulates a servo. + */ +//#define BLTOUCH +#if ENABLED(BLTOUCH) + //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed +#endif + +// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) +//#define SOLENOID_PROBE + +// A sled-mounted probe like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice. +//#define RACK_AND_PINION_PROBE +#if ENABLED(RACK_AND_PINION_PROBE) + #define Z_PROBE_DEPLOY_X X_MIN_POS + #define Z_PROBE_RETRACT_X X_MAX_POS +#endif + +// +// For Z_PROBE_ALLEN_KEY see the Delta example configurations. +// + +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] + +// Certain types of probes need to stay away from edges +#define MIN_PROBE_EDGE 10 + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 8000 + +// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) +#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z + +// Feedrate (mm/m) for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) + +// The number of probes to perform at each point. +// Set to 2 for a fast/slow probe, using the second probe result. +// Set to 3 or more for slow probes, averaging the results. +//#define MULTIPLE_PROBING 2 + +/** + * Z probes require clearance when deploying, stowing, and moving between + * probe points to avoid hitting the bed and other hardware. + * Servo-mounted probes require extra space for the arm to rotate. + * Inductive probes need space to keep from triggering early. + * + * Use these settings to specify the distance (mm) to raise the probe (or + * lower the bed). The values set here apply over and above any (negative) + * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD. + * Only integer values >= 1 are valid here. + * + * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. + * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. + */ +#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow +#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points +#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes +//#define Z_AFTER_PROBING 5 // Z position after probing is done + +#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping + +// For M851 give a range for adjusting the Z probe offset +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + +// Enable the M48 repeatability test to test probe accuracy +//#define Z_MIN_PROBE_REPEATABILITY_TEST + +// Before deploy/stow pause for user confirmation +//#define PAUSE_BEFORE_DEPLOY_STOW + +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + +// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 +// :{ 0:'Low', 1:'High' } +#define X_ENABLE_ON 0 +#define Y_ENABLE_ON 0 +#define Z_ENABLE_ON 0 +#define E_ENABLE_ON 0 // For all extruders + +// Disables axis stepper immediately when it's not being used. +// WARNING: When motors turn off there is a chance of losing position accuracy! +#define DISABLE_X false +#define DISABLE_Y false +#define DISABLE_Z false + +// Warn on display about possibly reduced accuracy +//#define DISABLE_REDUCED_ACCURACY_WARNING + +// @section extruder + +#define DISABLE_E false // For all extruders +#define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled + +// @section machine + +// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. +#define INVERT_X_DIR false +#define INVERT_Y_DIR true +#define INVERT_Z_DIR false + +// @section extruder + +// For direct drive extruder v9 set to true, for geared extruder set to false. +#define INVERT_E0_DIR false +#define INVERT_E1_DIR false +#define INVERT_E2_DIR false +#define INVERT_E3_DIR false +#define INVERT_E4_DIR false +#define INVERT_E5_DIR false + +// @section homing + +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + +//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off. + +//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ... + // Be sure you have this distance over your Z_MAX_POS in case. + +// Direction of endstops when homing; 1=MAX, -1=MIN +// :[-1,1] +#define X_HOME_DIR -1 +#define Y_HOME_DIR 1 +#define Z_HOME_DIR -1 + +// @section machine + +// The size of the print bed +#define X_BED_SIZE 200 +#define Y_BED_SIZE 200 + +// Travel limits (mm) after homing, corresponding to endstop positions. +#define X_MIN_POS 0 +#define Y_MIN_POS 0 +#define Z_MIN_POS 0 +#define X_MAX_POS X_BED_SIZE +#define Y_MAX_POS Y_BED_SIZE +#define Z_MAX_POS 200 + +/** + * Software Endstops + * + * - Prevent moves outside the set machine bounds. + * - Individual axes can be disabled, if desired. + * - X and Y only apply to Cartesian robots. + * - Use 'M211' to set software endstops on/off or report current state + */ + +// Min software endstops constrain movement within minimum coordinate bounds +//#define MIN_SOFTWARE_ENDSTOPS +#if ENABLED(MIN_SOFTWARE_ENDSTOPS) + #define MIN_SOFTWARE_ENDSTOP_X + #define MIN_SOFTWARE_ENDSTOP_Y + #define MIN_SOFTWARE_ENDSTOP_Z +#endif + +// Max software endstops constrain movement within maximum coordinate bounds +//#define MAX_SOFTWARE_ENDSTOPS +#if ENABLED(MAX_SOFTWARE_ENDSTOPS) + #define MAX_SOFTWARE_ENDSTOP_X + #define MAX_SOFTWARE_ENDSTOP_Y + #define MAX_SOFTWARE_ENDSTOP_Z +#endif + +#if ENABLED(MIN_SOFTWARE_ENDSTOPS) || ENABLED(MAX_SOFTWARE_ENDSTOPS) + //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD +#endif + +/** + * Filament Runout Sensors + * Mechanical or opto endstops are used to check for the presence of filament. + * + * RAMPS-based boards use SERVO3_PIN for the first runout sensor. + * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc. + * By default the firmware assumes HIGH=FILAMENT PRESENT. + */ +//#define FILAMENT_RUNOUT_SENSOR +#if ENABLED(FILAMENT_RUNOUT_SENSOR) + #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each. + #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor. + #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins. + //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins. + + // Set one or more commands to execute on filament runout. + // (After 'M412 H' Marlin will ask the host to handle the process.) + #define FILAMENT_RUNOUT_SCRIPT "M600" + + // After a runout is detected, continue printing this length of filament + // before executing the runout script. Useful for a sensor at the end of + // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead. + //#define FILAMENT_RUNOUT_DISTANCE_MM 25 + + #ifdef FILAMENT_RUNOUT_DISTANCE_MM + // Enable this option to use an encoder disc that toggles the runout pin + // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM + // large enough to avoid false positives.) + //#define FILAMENT_MOTION_SENSOR + #endif +#endif + +//=========================================================================== +//=============================== Bed Leveling ============================== +//=========================================================================== +// @section calibrate + +/** + * Choose one of the options below to enable G29 Bed Leveling. The parameters + * and behavior of G29 will change depending on your selection. + * + * If using a Probe for Z Homing, enable Z_SAFE_HOMING also! + * + * - AUTO_BED_LEVELING_3POINT + * Probe 3 arbitrary points on the bed (that aren't collinear) + * You specify the XY coordinates of all 3 points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_LINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_BILINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a mesh, best for large or uneven beds. + * + * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling) + * A comprehensive bed leveling system combining the features and benefits + * of other systems. UBL also includes integrated Mesh Generation, Mesh + * Validation and Mesh Editing systems. + * + * - MESH_BED_LEVELING + * Probe a grid manually + * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.) + * For machines without a probe, Mesh Bed Leveling provides a method to perform + * leveling in steps so you can manually adjust the Z height at each grid-point. + * With an LCD controller the process is guided step-by-step. + */ +//#define AUTO_BED_LEVELING_3POINT +//#define AUTO_BED_LEVELING_LINEAR +//#define AUTO_BED_LEVELING_BILINEAR +//#define AUTO_BED_LEVELING_UBL +//#define MESH_BED_LEVELING + +/** + * Normally G28 leaves leveling disabled on completion. Enable + * this option to have G28 restore the prior leveling state. + */ +//#define RESTORE_LEVELING_AFTER_G28 + +/** + * Enable detailed logging of G28, G29, M48, etc. + * Turn on with the command 'M111 S32'. + * NOTE: Requires a lot of PROGMEM! + */ +//#define DEBUG_LEVELING_FEATURE + +#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL) + // Gradually reduce leveling correction until a set height is reached, + // at which point movement will be level to the machine's XY plane. + // The height can be set with M420 Z + #define ENABLE_LEVELING_FADE_HEIGHT + + // For Cartesian machines, instead of dividing moves on mesh boundaries, + // split up moves into short segments like a Delta. This follows the + // contours of the bed more closely than edge-to-edge straight moves. + #define SEGMENT_LEVELED_MOVES + #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one) + + /** + * Enable the G26 Mesh Validation Pattern tool. + */ + //#define G26_MESH_VALIDATION + #if ENABLED(G26_MESH_VALIDATION) + #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle. + #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool. + #define MESH_TEST_HOTEND_TEMP 205.0 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool. + #define MESH_TEST_BED_TEMP 60.0 // (°C) Default bed temperature for the G26 Mesh Validation Tool. + #endif + +#endif + +#if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR) + + // Set the number of grid points per dimension. + #define GRID_MAX_POINTS_X 3 + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + // Set the boundaries for probing (where the probe can reach). + //#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE)) + //#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE)) + + // Probe along the Y axis, advancing X after each column + //#define PROBE_Y_FIRST + + #if ENABLED(AUTO_BED_LEVELING_BILINEAR) + + // Beyond the probed grid, continue the implied tilt? + // Default is to maintain the height of the nearest edge. + //#define EXTRAPOLATE_BEYOND_GRID + + // + // Experimental Subdivision of the grid by Catmull-Rom method. + // Synthesizes intermediate points to produce a more detailed mesh. + // + //#define ABL_BILINEAR_SUBDIVISION + #if ENABLED(ABL_BILINEAR_SUBDIVISION) + // Number of subdivisions between probe points + #define BILINEAR_SUBDIVISIONS 3 + #endif + + #endif + +#elif ENABLED(AUTO_BED_LEVELING_UBL) + + //=========================================================================== + //========================= Unified Bed Leveling ============================ + //=========================================================================== + + //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh + + #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle + #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500 + + //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used + // as the Z-Height correction value. + +#elif ENABLED(MESH_BED_LEVELING) + + //=========================================================================== + //=================================== Mesh ================================== + //=========================================================================== + + #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS + +#endif // BED_LEVELING + +/** + * Points to probe for all 3-point Leveling procedures. + * Override if the automatically selected points are inadequate. + */ +#if ENABLED(AUTO_BED_LEVELING_3POINT) || ENABLED(AUTO_BED_LEVELING_UBL) + //#define PROBE_PT_1_X 15 + //#define PROBE_PT_1_Y 180 + //#define PROBE_PT_2_X 15 + //#define PROBE_PT_2_Y 20 + //#define PROBE_PT_3_X 170 + //#define PROBE_PT_3_Y 20 +#endif + +/** + * Add a bed leveling sub-menu for ABL or MBL. + * Include a guided procedure if manual probing is enabled. + */ +//#define LCD_BED_LEVELING + +#if ENABLED(LCD_BED_LEVELING) + #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis. + #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment + //#define MESH_EDIT_MENU // Add a menu to edit mesh points +#endif + +// Add a menu item to move between bed corners for manual bed adjustment +//#define LEVEL_BED_CORNERS + +#if ENABLED(LEVEL_BED_CORNERS) + #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners + //#define LEVEL_CENTER_TOO // Move to the center after the last corner +#endif + +/** + * Commands to execute at the end of G29 probing. + * Useful to retract or move the Z probe out of the way. + */ +//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" + + +// @section homing + +// The center of the bed is at (X=0, Y=0) +//#define BED_CENTER_AT_0_0 + +// Manually set the home position. Leave these undefined for automatic settings. +// For DELTA this is the top-center of the Cartesian print volume. +//#define MANUAL_X_HOME_POS 0 +//#define MANUAL_Y_HOME_POS 0 +//#define MANUAL_Z_HOME_POS 0 + +// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. +// +// With this feature enabled: +// +// - Allow Z homing only after X and Y homing AND stepper drivers still enabled. +// - If stepper drivers time out, it will need X and Y homing again before Z homing. +// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28). +// - Prevent Z homing when the Z probe is outside bed area. +// +//#define Z_SAFE_HOMING + +#if ENABLED(Z_SAFE_HOMING) + #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28). + #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28). +#endif + +// Homing speeds (mm/m) +#define HOMING_FEEDRATE_XY (50*60) +#define HOMING_FEEDRATE_Z (4*60) + +// Validate that endstops are triggered on homing moves +#define VALIDATE_HOMING_ENDSTOPS + +// @section calibrate + +/** + * Bed Skew Compensation + * + * This feature corrects for misalignment in the XYZ axes. + * + * Take the following steps to get the bed skew in the XY plane: + * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185) + * 2. For XY_DIAG_AC measure the diagonal A to C + * 3. For XY_DIAG_BD measure the diagonal B to D + * 4. For XY_SIDE_AD measure the edge A to D + * + * Marlin automatically computes skew factors from these measurements. + * Skew factors may also be computed and set manually: + * + * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2 + * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD))) + * + * If desired, follow the same procedure for XZ and YZ. + * Use these diagrams for reference: + * + * Y Z Z + * ^ B-------C ^ B-------C ^ B-------C + * | / / | / / | / / + * | / / | / / | / / + * | A-------D | A-------D | A-------D + * +-------------->X +-------------->X +-------------->Y + * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR + */ +//#define SKEW_CORRECTION + +#if ENABLED(SKEW_CORRECTION) + // Input all length measurements here: + #define XY_DIAG_AC 282.8427124746 + #define XY_DIAG_BD 282.8427124746 + #define XY_SIDE_AD 200 + + // Or, set the default skew factors directly here + // to override the above measurements: + #define XY_SKEW_FACTOR 0.0 + + //#define SKEW_CORRECTION_FOR_Z + #if ENABLED(SKEW_CORRECTION_FOR_Z) + #define XZ_DIAG_AC 282.8427124746 + #define XZ_DIAG_BD 282.8427124746 + #define YZ_DIAG_AC 282.8427124746 + #define YZ_DIAG_BD 282.8427124746 + #define YZ_SIDE_AD 200 + #define XZ_SKEW_FACTOR 0.0 + #define YZ_SKEW_FACTOR 0.0 + #endif + + // Enable this option for M852 to set skew at runtime + //#define SKEW_CORRECTION_GCODE +#endif + +//============================================================================= +//============================= Additional Features =========================== +//============================================================================= + +// @section extras + +// +// EEPROM +// +// The microcontroller can store settings in the EEPROM, e.g. max velocity... +// M500 - stores parameters in EEPROM +// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). +// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. +// +//#define EEPROM_SETTINGS // Enable for M500 and M501 commands +//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release! +#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM. + +// +// Host Keepalive +// +// When enabled Marlin will send a busy status message to the host +// every couple of seconds when it can't accept commands. +// +#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages +#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113. +#define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating + +// +// M100 Free Memory Watcher +// +//#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage + +// +// G20/G21 Inch mode support +// +//#define INCH_MODE_SUPPORT + +// +// M149 Set temperature units support +// +//#define TEMPERATURE_UNITS_SUPPORT + +// @section temperature + +// Preheat Constants +#define PREHEAT_1_LABEL "PLA" +#define PREHEAT_1_TEMP_HOTEND 180 +#define PREHEAT_1_TEMP_BED 70 +#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255 + +#define PREHEAT_2_LABEL "ABS" +#define PREHEAT_2_TEMP_HOTEND 240 +#define PREHEAT_2_TEMP_BED 110 +#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255 + +/** + * Nozzle Park + * + * Park the nozzle at the given XYZ position on idle or G27. + * + * The "P" parameter controls the action applied to the Z axis: + * + * P0 (Default) If Z is below park Z raise the nozzle. + * P1 Raise the nozzle always to Z-park height. + * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS. + */ +//#define NOZZLE_PARK_FEATURE + +#if ENABLED(NOZZLE_PARK_FEATURE) + // Specify a park position as { X, Y, Z } + #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 } + #define NOZZLE_PARK_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis) + #define NOZZLE_PARK_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers) +#endif + +/** + * Clean Nozzle Feature -- EXPERIMENTAL + * + * Adds the G12 command to perform a nozzle cleaning process. + * + * Parameters: + * P Pattern + * S Strokes / Repetitions + * T Triangles (P1 only) + * + * Patterns: + * P0 Straight line (default). This process requires a sponge type material + * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions) + * between the start / end points. + * + * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the + * number of zig-zag triangles to do. "S" defines the number of strokes. + * Zig-zags are done in whichever is the narrower dimension. + * For example, "G12 P1 S1 T3" will execute: + * + * -- + * | (X0, Y1) | /\ /\ /\ | (X1, Y1) + * | | / \ / \ / \ | + * A | | / \ / \ / \ | + * | | / \ / \ / \ | + * | (X0, Y0) | / \/ \/ \ | (X1, Y0) + * -- +--------------------------------+ + * |________|_________|_________| + * T1 T2 T3 + * + * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE. + * "R" specifies the radius. "S" specifies the stroke count. + * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT. + * + * Caveats: The ending Z should be the same as starting Z. + * Attention: EXPERIMENTAL. G-code arguments may change. + * + */ +//#define NOZZLE_CLEAN_FEATURE + +#if ENABLED(NOZZLE_CLEAN_FEATURE) + // Default number of pattern repetitions + #define NOZZLE_CLEAN_STROKES 12 + + // Default number of triangles + #define NOZZLE_CLEAN_TRIANGLES 3 + + // Specify positions as { X, Y, Z } + #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)} + #define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)} + + // Circular pattern radius + #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5 + // Circular pattern circle fragments number + #define NOZZLE_CLEAN_CIRCLE_FN 10 + // Middle point of circle + #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT + + // Moves the nozzle to the initial position + #define NOZZLE_CLEAN_GOBACK +#endif + +/** + * Print Job Timer + * + * Automatically start and stop the print job timer on M104/M109/M190. + * + * M104 (hotend, no wait) - high temp = none, low temp = stop timer + * M109 (hotend, wait) - high temp = start timer, low temp = stop timer + * M190 (bed, wait) - high temp = start timer, low temp = none + * + * The timer can also be controlled with the following commands: + * + * M75 - Start the print job timer + * M76 - Pause the print job timer + * M77 - Stop the print job timer + */ +#define PRINTJOB_TIMER_AUTOSTART + +/** + * Print Counter + * + * Track statistical data such as: + * + * - Total print jobs + * - Total successful print jobs + * - Total failed print jobs + * - Total time printing + * + * View the current statistics with M78. + */ +//#define PRINTCOUNTER + +//============================================================================= +//============================= LCD and SD support ============================ +//============================================================================= + +// @section lcd + +/** + * LCD LANGUAGE + * + * Select the language to display on the LCD. These languages are available: + * + * en, an, bg, ca, cz, da, de, el, el-gr, es, eu, fi, fr, gl, hr, it, + * jp-kana, ko_KR, nl, pl, pt, pt-br, ru, sk, tr, uk, zh_CN, zh_TW, test + * + * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp-kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' } + */ +#define LCD_LANGUAGE en + +/** + * LCD Character Set + * + * Note: This option is NOT applicable to Graphical Displays. + * + * All character-based LCDs provide ASCII plus one of these + * language extensions: + * + * - JAPANESE ... the most common + * - WESTERN ... with more accented characters + * - CYRILLIC ... for the Russian language + * + * To determine the language extension installed on your controller: + * + * - Compile and upload with LCD_LANGUAGE set to 'test' + * - Click the controller to view the LCD menu + * - The LCD will display Japanese, Western, or Cyrillic text + * + * See http://marlinfw.org/docs/development/lcd_language.html + * + * :['JAPANESE', 'WESTERN', 'CYRILLIC'] + */ +#define DISPLAY_CHARSET_HD44780 JAPANESE + +/** + * Info Screen Style (0:Classic, 1:Prusa) + * + * :[0:'Classic', 1:'Prusa'] + */ +#define LCD_INFO_SCREEN_STYLE 0 + +/** + * SD CARD + * + * SD Card support is disabled by default. If your controller has an SD slot, + * you must uncomment the following option or it won't work. + * + */ +//#define SDSUPPORT + +/** + * SD CARD: SPI SPEED + * + * Enable one of the following items for a slower SPI transfer speed. + * This may be required to resolve "volume init" errors. + */ +//#define SPI_SPEED SPI_HALF_SPEED +//#define SPI_SPEED SPI_QUARTER_SPEED +//#define SPI_SPEED SPI_EIGHTH_SPEED + +/** + * SD CARD: ENABLE CRC + * + * Use CRC checks and retries on the SD communication. + */ +//#define SD_CHECK_AND_RETRY + +/** + * LCD Menu Items + * + * Disable all menus and only display the Status Screen, or + * just remove some extraneous menu items to recover space. + */ +//#define NO_LCD_MENUS +//#define SLIM_LCD_MENUS + +// +// ENCODER SETTINGS +// +// This option overrides the default number of encoder pulses needed to +// produce one step. Should be increased for high-resolution encoders. +// +//#define ENCODER_PULSES_PER_STEP 4 + +// +// Use this option to override the number of step signals required to +// move between next/prev menu items. +// +//#define ENCODER_STEPS_PER_MENU_ITEM 1 + +/** + * Encoder Direction Options + * + * Test your encoder's behavior first with both options disabled. + * + * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION. + * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION. + * Reversed Value Editing only? Enable BOTH options. + */ + +// +// This option reverses the encoder direction everywhere. +// +// Set this option if CLOCKWISE causes values to DECREASE +// +//#define REVERSE_ENCODER_DIRECTION + +// +// This option reverses the encoder direction for navigating LCD menus. +// +// If CLOCKWISE normally moves DOWN this makes it go UP. +// If CLOCKWISE normally moves UP this makes it go DOWN. +// +//#define REVERSE_MENU_DIRECTION + +// +// Individual Axis Homing +// +// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. +// +//#define INDIVIDUAL_AXIS_HOMING_MENU + +// +// SPEAKER/BUZZER +// +// If you have a speaker that can produce tones, enable it here. +// By default Marlin assumes you have a buzzer with a fixed frequency. +// +//#define SPEAKER + +// +// The duration and frequency for the UI feedback sound. +// Set these to 0 to disable audio feedback in the LCD menus. +// +// Note: Test audio output with the G-Code: +// M300 S P +// +//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2 +//#define LCD_FEEDBACK_FREQUENCY_HZ 5000 + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//======================== (Character-based LCDs) ========================= +//============================================================================= + +// +// RepRapDiscount Smart Controller. +// http://reprap.org/wiki/RepRapDiscount_Smart_Controller +// +// Note: Usually sold with a white PCB. +// +//#define REPRAP_DISCOUNT_SMART_CONTROLLER + +// +// Original RADDS LCD Display+Encoder+SDCardReader +// http://doku.radds.org/dokumentation/lcd-display/ +// +//#define RADDS_DISPLAY + +// +// ULTIMAKER Controller. +// +//#define ULTIMAKERCONTROLLER + +// +// ULTIPANEL as seen on Thingiverse. +// +//#define ULTIPANEL + +// +// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) +// http://reprap.org/wiki/PanelOne +// +//#define PANEL_ONE + +// +// GADGETS3D G3D LCD/SD Controller +// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel +// +// Note: Usually sold with a blue PCB. +// +//#define G3D_PANEL + +// +// RigidBot Panel V1.0 +// http://www.inventapart.com/ +// +//#define RIGIDBOT_PANEL + +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// ANET and Tronxy 20x4 Controller +// +//#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin. + // This LCD is known to be susceptible to electrical interference + // which scrambles the display. Pressing any button clears it up. + // This is a LCD2004 display with 5 analog buttons. + +// +// Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD. +// +//#define ULTRA_LCD + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//===================== (I2C and Shift-Register LCDs) ===================== +//============================================================================= + +// +// CONTROLLER TYPE: I2C +// +// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C +// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C +// + +// +// Elefu RA Board Control Panel +// http://www.elefu.com/index.php?route=product/product&product_id=53 +// +//#define RA_CONTROL_PANEL + +// +// Sainsmart (YwRobot) LCD Displays +// +// These require F.Malpartida's LiquidCrystal_I2C library +// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home +// +//#define LCD_SAINSMART_I2C_1602 +//#define LCD_SAINSMART_I2C_2004 + +// +// Generic LCM1602 LCD adapter +// +//#define LCM1602 + +// +// PANELOLU2 LCD with status LEDs, +// separate encoder and click inputs. +// +// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later. +// For more info: https://github.com/lincomatic/LiquidTWI2 +// +// Note: The PANELOLU2 encoder click input can either be directly connected to +// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). +// +//#define LCD_I2C_PANELOLU2 + +// +// Panucatt VIKI LCD with status LEDs, +// integrated click & L/R/U/D buttons, separate encoder inputs. +// +//#define LCD_I2C_VIKI + +// +// CONTROLLER TYPE: Shift register panels +// + +// +// 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH +// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD +// +//#define SAV_3DLCD + +// +// 3-wire SR LCD with strobe using 74HC4094 +// https://github.com/mikeshub/SailfishLCD +// Uses the code directly from Sailfish +// +//#define FF_INTERFACEBOARD + +//============================================================================= +//======================= LCD / Controller Selection ======================= +//========================= (Graphical LCDs) ======================== +//============================================================================= + +// +// CONTROLLER TYPE: Graphical 128x64 (DOGM) +// +// IMPORTANT: The U8glib library is required for Graphical Display! +// https://github.com/olikraus/U8glib_Arduino +// + +// +// RepRapDiscount FULL GRAPHIC Smart Controller +// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller +// +//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + +// +// ReprapWorld Graphical LCD +// https://reprapworld.com/?products_details&products_id/1218 +// +//#define REPRAPWORLD_GRAPHICAL_LCD + +// +// Activate one of these if you have a Panucatt Devices +// Viki 2.0 or mini Viki with Graphic LCD +// http://panucatt.com +// +//#define VIKI2 +//#define miniVIKI + +// +// MakerLab Mini Panel with graphic +// controller and SD support - http://reprap.org/wiki/Mini_panel +// +//#define MINIPANEL + +// +// MaKr3d Makr-Panel with graphic controller and SD support. +// http://reprap.org/wiki/MaKr3d_MaKrPanel +// +//#define MAKRPANEL + +// +// Adafruit ST7565 Full Graphic Controller. +// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ +// +//#define ELB_FULL_GRAPHIC_CONTROLLER + +// +// BQ LCD Smart Controller shipped by +// default with the BQ Hephestos 2 and Witbox 2. +// +//#define BQ_LCD_SMART_CONTROLLER + +// +// Cartesio UI +// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// +//#define CARTESIO_UI + +// +// LCD for Melzi Card with Graphical LCD +// +//#define LCD_FOR_MELZI + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + //#define U8GLIB_SSD1306 + #define U8GLIB_SH1106 +#endif + +// +// Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder +// https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) +// +//#define ULTI_CONTROLLER + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// ANET and Tronxy Graphical Controller +// +// Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6 +// A clone of the RepRapDiscount full graphics display but with +// different pins/wiring (see pins_ANET_10.h). +// +//#define ANET_FULL_GRAPHICS_LCD + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// AZSMZ 12864 LCD with SD +// https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html +// +//#define AZSMZ_12864 + +// +// Silvergate GLCD controller +// http://github.com/android444/Silvergate +// +//#define SILVER_GATE_GLCD_CONTROLLER + +// +// Extensible UI +// +// Enable third-party or vendor customized user interfaces that aren't +// packaged with Marlin. Source code for the user interface will need to +// be placed in "src/lcd/extensible_ui/lib" +// +//#define EXTENSIBLE_UI + +//============================================================================= +//=============================== Graphical TFTs ============================== +//============================================================================= + +// +// MKS Robin 320x240 color display +// +//#define MKS_ROBIN_TFT + +//============================================================================= +//============================ Other Controllers ============================ +//============================================================================= + +// +// CONTROLLER TYPE: Standalone / Serial +// + +// +// LCD for Malyan M200 printers. +// +//#define MALYAN_LCD + +// +// CONTROLLER TYPE: Keypad / Add-on +// + +// +// RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 +// +// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key +// is pressed, a value of 10.0 means 10mm per click. +// +//#define REPRAPWORLD_KEYPAD +//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 + +//============================================================================= +//=============================== Extra Features ============================== +//============================================================================= + +// @section extras + +// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino +//#define FAST_PWM_FAN + +// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency +// which is not as annoying as with the hardware PWM. On the other hand, if this frequency +// is too low, you should also increment SOFT_PWM_SCALE. +//#define FAN_SOFT_PWM + +// Incrementing this by 1 will double the software PWM frequency, +// affecting heaters, and the fan if FAN_SOFT_PWM is enabled. +// However, control resolution will be halved for each increment; +// at zero value, there are 128 effective control positions. +#define SOFT_PWM_SCALE 0 + +// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can +// be used to mitigate the associated resolution loss. If enabled, +// some of the PWM cycles are stretched so on average the desired +// duty cycle is attained. +//#define SOFT_PWM_DITHER + +// Temperature status LEDs that display the hotend and bed temperature. +// If all hotends, bed temperature, and target temperature are under 54C +// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis) +//#define TEMP_STAT_LEDS + +// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure +//#define SF_ARC_FIX + +// Support for the BariCUDA Paste Extruder +//#define BARICUDA + +// Support for BlinkM/CyzRgb +//#define BLINKM + +// Support for PCA9632 PWM LED driver +//#define PCA9632 + +// Support for PCA9533 PWM LED driver +// https://github.com/mikeshub/SailfishRGB_LED +//#define PCA9533 + +/** + * RGB LED / LED Strip Control + * + * Enable support for an RGB LED connected to 5V digital pins, or + * an RGB Strip connected to MOSFETs controlled by digital pins. + * + * Adds the M150 command to set the LED (or LED strip) color. + * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of + * luminance values can be set from 0 to 255. + * For Neopixel LED an overall brightness parameter is also available. + * + * *** CAUTION *** + * LED Strips require a MOSFET Chip between PWM lines and LEDs, + * as the Arduino cannot handle the current the LEDs will require. + * Failure to follow this precaution can destroy your Arduino! + * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * more current than the Arduino 5V linear regulator can produce. + * *** CAUTION *** + * + * LED Type. Enable only one of the following two options. + * + */ +//#define RGB_LED +//#define RGBW_LED + +#if ENABLED(RGB_LED) || ENABLED(RGBW_LED) + #define RGB_LED_R_PIN 34 + #define RGB_LED_G_PIN 43 + #define RGB_LED_B_PIN 35 + #define RGB_LED_W_PIN -1 +#endif + +// Support for Adafruit Neopixel LED driver +#define NEOPIXEL_LED +#if ENABLED(NEOPIXEL_LED) + #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 20 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) + #define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + #define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup +#endif + +/** + * Printer Event LEDs + * + * During printing, the LEDs will reflect the printer status: + * + * - Gradually change from blue to violet as the heated bed gets to target temp + * - Gradually change from violet to red as the hotend gets to temperature + * - Change to white to illuminate work surface + * - Change to green once print has finished + * - Turn off after the print has finished and the user has pushed a button + */ +#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(PCA9533)|| ENABLED(NEOPIXEL_LED) + #define PRINTER_EVENT_LEDS +#endif + +/** + * R/C SERVO support + * Sponsored by TrinityLabs, Reworked by codexmas + */ + +/** + * Number of servos + * + * For some servo-related options NUM_SERVOS will be set automatically. + * Set this manually if there are extra servos needing manual control. + * Leave undefined or set to 0 to entirely disable the servo subsystem. + */ +//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command + +// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. +// 300ms is a good value but you can try less delay. +// If the servo can't reach the requested position, increase it. +#define SERVO_DELAY { 300 } + +// Only power servos during movement, otherwise leave off to prevent jitter +//#define DEACTIVATE_SERVOS_AFTER_MOVE + +// Allow servo angle to be edited and saved to EEPROM +//#define EDITABLE_SERVO_ANGLES diff --git a/Marlin/src/core/boards.h b/Marlin/src/core/boards.h index 6f617744a8..808fb18966 100644 --- a/Marlin/src/core/boards.h +++ b/Marlin/src/core/boards.h @@ -222,6 +222,12 @@ #define BOARD_ARCHIM1 1591 // UltiMachine Archim1 (with DRV8825 drivers) #define BOARD_ARCHIM2 1592 // UltiMachine Archim2 (with TMC2130 drivers) #define BOARD_ALLIGATOR 1602 // Alligator Board R2 + +// +// SAM3X8C ARM Cortex M3 +// + +#define BOARD_PRINTRBOARD_G2 1620 // PRINTRBOARD G2 #define BOARD_ADSK 1610 // Arduino DUE Shield Kit (ADSK) // diff --git a/Marlin/src/gcode/feature/digipot/M907-M910.cpp b/Marlin/src/gcode/feature/digipot/M907-M910.cpp index 8e6ca7c919..e7cad77757 100644 --- a/Marlin/src/gcode/feature/digipot/M907-M910.cpp +++ b/Marlin/src/gcode/feature/digipot/M907-M910.cpp @@ -44,37 +44,37 @@ void GcodeSuite::M907() { #if HAS_DIGIPOTSS - LOOP_XYZE(i) if (parser.seen(axis_codes[i])) stepper.digipot_current(i, parser.value_int()); - if (parser.seen('B')) stepper.digipot_current(4, parser.value_int()); - if (parser.seen('S')) for (uint8_t i = 0; i <= 4; i++) stepper.digipot_current(i, parser.value_int()); + LOOP_XYZE(i) if (parser.seenval(axis_codes[i])) stepper.digipot_current(i, parser.value_int()); + if (parser.seenval('B')) stepper.digipot_current(4, parser.value_int()); + if (parser.seenval('S')) for (uint8_t i = 0; i <= 4; i++) stepper.digipot_current(i, parser.value_int()); #elif HAS_MOTOR_CURRENT_PWM - #if PIN_EXISTS(MOTOR_CURRENT_PWM_XY) - if (parser.seen('X')) stepper.digipot_current(0, parser.value_int()); + #if PIN_EXISTS(MOTOR_CURRENT_PWM_X) || PIN_EXISTS(MOTOR_CURRENT_PWM_Y) || PIN_EXISTS(MOTOR_CURRENT_PWM_XY) + if (parser.seenval('X') || parser.seenval('Y')) stepper.digipot_current(0, parser.value_int()); #endif #if PIN_EXISTS(MOTOR_CURRENT_PWM_Z) - if (parser.seen('Z')) stepper.digipot_current(1, parser.value_int()); + if (parser.seenval('Z')) stepper.digipot_current(1, parser.value_int()); #endif #if PIN_EXISTS(MOTOR_CURRENT_PWM_E) - if (parser.seen('E')) stepper.digipot_current(2, parser.value_int()); + if (parser.seenval('E')) stepper.digipot_current(2, parser.value_int()); #endif #endif #if ENABLED(DIGIPOT_I2C) // this one uses actual amps in floating point - LOOP_XYZE(i) if (parser.seen(axis_codes[i])) digipot_i2c_set_current(i, parser.value_float()); + LOOP_XYZE(i) if (parser.seenval(axis_codes[i])) digipot_i2c_set_current(i, parser.value_float()); // for each additional extruder (named B,C,D,E..., channels 4,5,6,7...) - for (uint8_t i = NUM_AXIS; i < DIGIPOT_I2C_NUM_CHANNELS; i++) if (parser.seen('B' + i - (NUM_AXIS))) digipot_i2c_set_current(i, parser.value_float()); + for (uint8_t i = NUM_AXIS; i < DIGIPOT_I2C_NUM_CHANNELS; i++) if (parser.seenval('B' + i - (NUM_AXIS))) digipot_i2c_set_current(i, parser.value_float()); #endif #if ENABLED(DAC_STEPPER_CURRENT) - if (parser.seen('S')) { + if (parser.seenval('S')) { const float dac_percent = parser.value_float(); for (uint8_t i = 0; i <= 4; i++) dac_current_percent(i, dac_percent); } - LOOP_XYZE(i) if (parser.seen(axis_codes[i])) dac_current_percent(i, parser.value_float()); + LOOP_XYZE(i) if (parser.seenval(axis_codes[i])) dac_current_percent(i, parser.value_float()); #endif } diff --git a/Marlin/src/module/stepper.cpp b/Marlin/src/module/stepper.cpp index 57e8e4195c..afc1c3f3f8 100644 --- a/Marlin/src/module/stepper.cpp +++ b/Marlin/src/module/stepper.cpp @@ -2485,99 +2485,107 @@ void Stepper::report_positions() { #endif // HAS_MOTOR_CURRENT_PWM -#if HAS_DIGIPOTSS || HAS_MOTOR_CURRENT_PWM +#if !MB(PRINTRBOARD_G2) - void Stepper::digipot_current(const uint8_t driver, const int16_t current) { + #if HAS_DIGIPOTSS || HAS_MOTOR_CURRENT_PWM - #if HAS_DIGIPOTSS + void Stepper::digipot_current(const uint8_t driver, const int16_t current) { - const uint8_t digipot_ch[] = DIGIPOT_CHANNELS; - digitalPotWrite(digipot_ch[driver], current); + #if HAS_DIGIPOTSS - #elif HAS_MOTOR_CURRENT_PWM + const uint8_t digipot_ch[] = DIGIPOT_CHANNELS; + digitalPotWrite(digipot_ch[driver], current); - if (WITHIN(driver, 0, COUNT(motor_current_setting) - 1)) - motor_current_setting[driver] = current; // update motor_current_setting + #elif HAS_MOTOR_CURRENT_PWM - #define _WRITE_CURRENT_PWM(P) analogWrite(MOTOR_CURRENT_PWM_## P ##_PIN, 255L * current / (MOTOR_CURRENT_PWM_RANGE)) - switch (driver) { - case 0: - #if PIN_EXISTS(MOTOR_CURRENT_PWM_X) - _WRITE_CURRENT_PWM(X); - #endif - #if PIN_EXISTS(MOTOR_CURRENT_PWM_Y) - _WRITE_CURRENT_PWM(Y); - #endif - #if PIN_EXISTS(MOTOR_CURRENT_PWM_XY) - _WRITE_CURRENT_PWM(XY); - #endif - break; - case 1: - #if PIN_EXISTS(MOTOR_CURRENT_PWM_Z) - _WRITE_CURRENT_PWM(Z); - #endif - break; - case 2: - #if PIN_EXISTS(MOTOR_CURRENT_PWM_E) - _WRITE_CURRENT_PWM(E); - #endif - #if PIN_EXISTS(MOTOR_CURRENT_PWM_E0) - _WRITE_CURRENT_PWM(E0); - #endif - #if PIN_EXISTS(MOTOR_CURRENT_PWM_E1) - _WRITE_CURRENT_PWM(E1); - #endif - break; - } - #endif - } + if (WITHIN(driver, 0, COUNT(motor_current_setting) - 1)) + motor_current_setting[driver] = current; // update motor_current_setting - void Stepper::digipot_init() { - - #if HAS_DIGIPOTSS - - static const uint8_t digipot_motor_current[] = DIGIPOT_MOTOR_CURRENT; - - SPI.begin(); - SET_OUTPUT(DIGIPOTSS_PIN); - - for (uint8_t i = 0; i < COUNT(digipot_motor_current); i++) { - //digitalPotWrite(digipot_ch[i], digipot_motor_current[i]); - digipot_current(i, digipot_motor_current[i]); - } - - #elif HAS_MOTOR_CURRENT_PWM - - #if PIN_EXISTS(MOTOR_CURRENT_PWM_X) - SET_OUTPUT(MOTOR_CURRENT_PWM_X_PIN); - #endif - #if PIN_EXISTS(MOTOR_CURRENT_PWM_Y) - SET_OUTPUT(MOTOR_CURRENT_PWM_Y_PIN); - #endif - #if PIN_EXISTS(MOTOR_CURRENT_PWM_XY) - SET_OUTPUT(MOTOR_CURRENT_PWM_XY_PIN); - #endif - #if PIN_EXISTS(MOTOR_CURRENT_PWM_Z) - SET_OUTPUT(MOTOR_CURRENT_PWM_Z_PIN); - #endif - #if PIN_EXISTS(MOTOR_CURRENT_PWM_E) - SET_OUTPUT(MOTOR_CURRENT_PWM_E_PIN); - #endif - #if PIN_EXISTS(MOTOR_CURRENT_PWM_E0) - SET_OUTPUT(MOTOR_CURRENT_PWM_E0_PIN); - #endif - #if PIN_EXISTS(MOTOR_CURRENT_PWM_E1) - SET_OUTPUT(MOTOR_CURRENT_PWM_E1_PIN); + #define _WRITE_CURRENT_PWM(P) analogWrite(MOTOR_CURRENT_PWM_## P ##_PIN, 255L * current / (MOTOR_CURRENT_PWM_RANGE)) + switch (driver) { + case 0: + #if PIN_EXISTS(MOTOR_CURRENT_PWM_X) + _WRITE_CURRENT_PWM(X); + #endif + #if PIN_EXISTS(MOTOR_CURRENT_PWM_Y) + _WRITE_CURRENT_PWM(Y); + #endif + #if PIN_EXISTS(MOTOR_CURRENT_PWM_XY) + _WRITE_CURRENT_PWM(XY); + #endif + break; + case 1: + #if PIN_EXISTS(MOTOR_CURRENT_PWM_Z) + _WRITE_CURRENT_PWM(Z); + #endif + break; + case 2: + #if PIN_EXISTS(MOTOR_CURRENT_PWM_E) + _WRITE_CURRENT_PWM(E); + #endif + #if PIN_EXISTS(MOTOR_CURRENT_PWM_E0) + _WRITE_CURRENT_PWM(E0); + #endif + #if PIN_EXISTS(MOTOR_CURRENT_PWM_E1) + _WRITE_CURRENT_PWM(E1); + #endif + break; + } #endif + } - refresh_motor_power(); + void Stepper::digipot_init() { - // Set Timer5 to 31khz so the PWM of the motor power is as constant as possible. (removes a buzzing noise) - #ifdef __AVR__ - SET_CS5(PRESCALER_1); + #if HAS_DIGIPOTSS + + static const uint8_t digipot_motor_current[] = DIGIPOT_MOTOR_CURRENT; + + SPI.begin(); + SET_OUTPUT(DIGIPOTSS_PIN); + + for (uint8_t i = 0; i < COUNT(digipot_motor_current); i++) { + //digitalPotWrite(digipot_ch[i], digipot_motor_current[i]); + digipot_current(i, digipot_motor_current[i]); + } + + #elif HAS_MOTOR_CURRENT_PWM + + #if PIN_EXISTS(MOTOR_CURRENT_PWM_X) + SET_OUTPUT(MOTOR_CURRENT_PWM_X_PIN); + #endif + #if PIN_EXISTS(MOTOR_CURRENT_PWM_Y) + SET_OUTPUT(MOTOR_CURRENT_PWM_Y_PIN); + #endif + #if PIN_EXISTS(MOTOR_CURRENT_PWM_XY) + SET_OUTPUT(MOTOR_CURRENT_PWM_XY_PIN); + #endif + #if PIN_EXISTS(MOTOR_CURRENT_PWM_Z) + SET_OUTPUT(MOTOR_CURRENT_PWM_Z_PIN); + #endif + #if PIN_EXISTS(MOTOR_CURRENT_PWM_E) + SET_OUTPUT(MOTOR_CURRENT_PWM_E_PIN); + #endif + #if PIN_EXISTS(MOTOR_CURRENT_PWM_E0) + SET_OUTPUT(MOTOR_CURRENT_PWM_E0_PIN); + #endif + #if PIN_EXISTS(MOTOR_CURRENT_PWM_E1) + SET_OUTPUT(MOTOR_CURRENT_PWM_E1_PIN); + #endif + + refresh_motor_power(); + + // Set Timer5 to 31khz so the PWM of the motor power is as constant as possible. (removes a buzzing noise) + #ifdef __AVR__ + SET_CS5(PRESCALER_1); + #endif #endif - #endif - } + } + + #endif + +#else + + #include "../HAL/HAL_DUE/G2_PWM.h" #endif diff --git a/Marlin/src/pins/pins.h b/Marlin/src/pins/pins.h index 8c874e85fd..ba034d3e49 100644 --- a/Marlin/src/pins/pins.h +++ b/Marlin/src/pins/pins.h @@ -393,6 +393,8 @@ #include "pins_ALLIGATOR_R2.h" // SAM3X8E env:DUE env:DUE_debug #elif MB(ADSK) #include "pins_ADSK.h" // SAM3X8E env:DUE env:DUE_debug +#elif MB(PRINTRBOARD_G2) + #include "pins_PRINTRBOARD_G2.h" // SAM3X8C env:DUE_USB // // STM32 ARM Cortex-M3 diff --git a/Marlin/src/pins/pinsDebug_list.h b/Marlin/src/pins/pinsDebug_list.h index ac3855a539..07c58c7069 100644 --- a/Marlin/src/pins/pinsDebug_list.h +++ b/Marlin/src/pins/pinsDebug_list.h @@ -614,6 +614,12 @@ #if PIN_EXISTS(MOTOR_CURRENT_PWM_XY) REPORT_NAME_DIGITAL(__LINE__, MOTOR_CURRENT_PWM_XY_PIN) #endif +#if PIN_EXISTS(MOTOR_CURRENT_PWM_X) + REPORT_NAME_DIGITAL(__LINE__, MOTOR_CURRENT_PWM_X_PIN) +#endif +#if PIN_EXISTS(MOTOR_CURRENT_PWM_Y) + REPORT_NAME_DIGITAL(__LINE__, MOTOR_CURRENT_PWM_Y_PIN) +#endif #if PIN_EXISTS(MOTOR_CURRENT_PWM_Z) REPORT_NAME_DIGITAL(__LINE__, MOTOR_CURRENT_PWM_Z_PIN) #endif @@ -1154,3 +1160,6 @@ #if PIN_EXISTS(L6470_RESET_CHAIN) REPORT_NAME_DIGITAL(__LINE__, L6470_RESET_CHAIN_PIN) #endif +#if PIN_EXISTS(FET_SAFETY) + REPORT_NAME_DIGITAL(__LINE__, FET_SAFETY_PIN) +#endif diff --git a/Marlin/src/pins/pins_PRINTRBOARD_G2.h b/Marlin/src/pins/pins_PRINTRBOARD_G2.h new file mode 100644 index 0000000000..02f094498f --- /dev/null +++ b/Marlin/src/pins/pins_PRINTRBOARD_G2.h @@ -0,0 +1,177 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (C) 2016, 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/** + * PRINTRBOARD_G2 + */ + +#ifndef __SAM3X8E__ + #error "Oops! Select 'Arduino Due' in 'Tools > Board.'" +#endif + +#ifndef BOARD_NAME + #define BOARD_NAME "PRINTRBOARD_G2" +#endif + +// +// Servos +// +//#define SERVO0_PIN -1 +//#define SERVO1_PIN -1 + +// +// Limit Switches +// +#define X_MIN_PIN 22 // PB26 +#define Y_MAX_PIN 18 // PA11 +#define Z_MIN_PIN 19 // PA10 + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 22 +#endif + +#ifndef FIL_RUNOUT_PIN + //#define FIL_RUNOUT_PIN 57 // PA22 +#endif +#ifndef FIL_RUNOUT2_PIN + //#define FIL_RUNOUT2_PIN 21 // PB13 +#endif + + +// +// LED defines +// +//#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) +//#define NEOPIXEL_PIN 20 // LED driving pin on motherboard +//#define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip + + + +//#define SDA0 20 // PB12 NeoPixel pin I2C data +//#define SCL0 21 // PB13 I2C clock + +// D0_12 #REF! (INDICATOR_LED) +// B28 JTAG-CLK +// B31 JTAG_TMS /SWD_DIO +//A18 INTERRUPT_OUT +//A12 USART_RX not used +//A13 USART_TX not used +//A14 UART_RTS +//A15 UART_CTS +//PB2 Unassigned +//PB4 to PB9 Unassigned +//#define UART_RX_PIN 0 // PA8 "RX0" +//#define UART_TX_PIN 1 // PA9 "TX0" +//#define UART_RTS_PIN 23 // PA14 +//#define UART_CTS_PIN 24 // PA15 + +// +// Steppers +// +#define Z_STEP_PIN 73 // PA21 MOTOR 1 +#define Z_DIR_PIN 75 // PA26 +#define Z_ENABLE_PIN 74 // PA25 + +#define X_STEP_PIN 66 // PB15 MOTOR 2 +#define X_DIR_PIN 54 // PA16 +#define X_ENABLE_PIN 67 // PB16 + +#define Y_STEP_PIN 34 // PA29 MOTOR 3 +#define Y_DIR_PIN 35 // PB1 +#define Y_ENABLE_PIN 36 // PB0 + +#define E0_STEP_PIN 53 // PB14 MOTOR 4 +#define E0_DIR_PIN 78 // PB23 +#define E0_ENABLE_PIN 37 // PB22 + +// Microstepping mode pins +#define Z_MS1_PIN 52 // PB21 MODE0 MOTOR 1 +#define Z_MS2_PIN 52 // PB21 MODE1 +#define Z_MS3_PIN 65 // PB20 MODE2 + +#define X_MS1_PIN 43 // PA20 MODE0 MOTOR 2 +#define X_MS2_PIN 43 // PA20 MODE1 +#define X_MS3_PIN 42 // PA19 MODE2 + +#define Y_MS1_PIN 77 // PA28 MODE0 MOTOR 3 +#define Y_MS2_PIN 77 // PA28 MODE1 +#define Y_MS3_PIN 76 // PA27 MODE2 + +#define E0_MS1_PIN 38 // PB11 MODE0 MOTOR 4 +#define E0_MS2_PIN 38 // PB11 MODE1 +#define E0_MS3_PIN 39 // PB10 MODE2 + +// Motor current PWM pins +#define MOTOR_CURRENT_PWM_X_PIN 62 // PB17 MOTOR 1 +#define MOTOR_CURRENT_PWM_Z_PIN 63 // PB18 MOTOR 2 +#define MOTOR_CURRENT_PWM_Y_PIN 64 // PB19 MOTOR 3 +#define MOTOR_CURRENT_PWM_E_PIN 61 // PA2 MOTOR 4 + +//#define DEFAULT_PWM_MOTOR_CURRENT { 300, 400, 1000} // XY Z E0, 1000 = 1000mAh + +// +// Temperature Sensors +// +#define TEMP_0_PIN 2 // digital 56 PA23 +#define TEMP_BED_PIN 5 // digital 59 PA4 + +// +// Heaters / Fans +// +#define HEATER_0_PIN 40 // PA5 +#define HEATER_BED_PIN 41 // PB24 + +#ifndef FAN_PIN + #define FAN_PIN 13 // PB27 Fan1A +#endif +#define FAN1_PIN 58 // PA6 Fan1B + +#define FET_SAFETY_PIN 31 // PA7 must be pulsed low every 50 mS or FETs are turned off +#define FET_SAFETY_DELAY 50 // 50 mS delay between pulses +#define FET_SAFETY_INVERTED true // true - negative going pulse of 2 uS + +///////////////////////////////////////////////////////// + +#define MISO_PIN 68 // set to unused pins for now +#define MOSI_PIN 69 // set to unused pins for now +#define SCK_PIN 70 // set to unused pins for now +#define SDSS 71 // set to unused pins for now + +/** + * G2 uses 8 pins that are not available in the DUE environment: + * 34 PA29 - Y_STEP_PIN + * 35 PB1 - Y_DIR_PIN + * 36 PB0 - Y_ENABLE_PIN + * 37 PB22 - E0_ENABLE_PIN + * 38 PB11 - E0_MS1_PIN - normally used by the USB native port + * 39 PB10 - E0_MS3_PIN - normally used by the USB native port + * 40 PA5 - HEATER_0_PIN + * 41 PB24 - HEATER_BED_PIN + * + * None of these are in the arduino_due_x variant so digitalWrite and digitalRead can't be used on them. + * + * They can be accessed via FASTIO functions WRITE, READ, OUT_WRITE, OUTPUT, ... + * + */