Merge pull request #3279 from thinkyhead/rc_filament_width_sensor

FILAMENT_SENSOR -> FILAMENT_WIDTH_SENSOR
2016-03-30 12:16:27 -07:00 · 2016-03-30 12:16:27 -07:00 · de333c4fea
parent 0f835c0c4e 507aef055f
commit de333c4fea
32 changed files with 90 additions and 94 deletions
--- a/.travis.yml
+++ b/.travis.yml
@ -124,11 +124,11 @@ script:
  - build_marlin
  # Enable filament sensor
  - restore_configs
-  - opt_enable FILAMENT_SENSOR
+  - opt_enable FILAMENT_WIDTH_SENSOR
  - build_marlin
  # Enable filament sensor with LCD display
  - restore_configs
-  - opt_enable ULTIMAKERCONTROLLER FILAMENT_SENSOR FILAMENT_LCD_DISPLAY
+  - opt_enable ULTIMAKERCONTROLLER FILAMENT_WIDTH_SENSOR FILAMENT_LCD_DISPLAY
  - build_marlin
  # Enable COREXY
  - restore_configs
--- a/Marlin/Conditionals.h
+++ b/Marlin/Conditionals.h
@ -513,7 +513,7 @@
  #define HAS_SERVO_1 (PIN_EXISTS(SERVO1))
  #define HAS_SERVO_2 (PIN_EXISTS(SERVO2))
  #define HAS_SERVO_3 (PIN_EXISTS(SERVO3))
-  #define HAS_FILAMENT_SENSOR (ENABLED(FILAMENT_SENSOR) && PIN_EXISTS(FILWIDTH))
+  #define HAS_FILAMENT_WIDTH_SENSOR (PIN_EXISTS(FILWIDTH))
  #define HAS_FILRUNOUT (PIN_EXISTS(FILRUNOUT))
  #define HAS_HOME (PIN_EXISTS(HOME))
  #define HAS_KILL (PIN_EXISTS(KILL))
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@ -920,11 +920,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 * Note may require analog pins to be defined for different motherboards
 **********************************************************************/
 // Uncomment below to enable
-//#define FILAMENT_SENSOR
+//#define FILAMENT_WIDTH_SENSOR

 #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  #define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
  #define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel

--- a/Marlin/Marlin.h
+++ b/Marlin/Marlin.h
@ -336,7 +336,7 @@ extern bool axis_homed[3]; // axis[n].is_homed
  extern int EtoPPressure;
 #endif

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  extern float filament_width_nominal;  //holds the theoretical filament diameter i.e., 3.00 or 1.75
  extern bool filament_sensor;  //indicates that filament sensor readings should control extrusion
  extern float filament_width_meas; //holds the filament diameter as accurately measured
--- a/Marlin/Marlin_main.cpp
+++ b/Marlin/Marlin_main.cpp
@ -405,7 +405,7 @@ static uint8_t target_extruder;
  float axis_scaling[3] = { 1, 1, 1 };    // Build size scaling, default to 1
 #endif

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  //Variables for Filament Sensor input
  float filament_width_nominal = DEFAULT_NOMINAL_FILAMENT_DIA;  //Set nominal filament width, can be changed with M404
  bool filament_sensor = false;  //M405 turns on filament_sensor control, M406 turns it off
@ -5454,21 +5454,19 @@ inline void gcode_M400() { st_synchronize(); }

 #endif // AUTO_BED_LEVELING_FEATURE && (HAS_SERVO_ENDSTOPS || Z_PROBE_ALLEN_KEY) && !Z_PROBE_SLED

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)

  /**
   * M404: Display or set the nominal filament width (3mm, 1.75mm ) W<3.0>
   */
  inline void gcode_M404() {
-    #if HAS_FILWIDTH
-      if (code_seen('W')) {
-        filament_width_nominal = code_value();
-      }
-      else {
-        SERIAL_PROTOCOLPGM("Filament dia (nominal mm):");
-        SERIAL_PROTOCOLLN(filament_width_nominal);
-      }
-    #endif
+    if (code_seen('W')) {
+      filament_width_nominal = code_value();
+    }
+    else {
+      SERIAL_PROTOCOLPGM("Filament dia (nominal mm):");
+      SERIAL_PROTOCOLLN(filament_width_nominal);
+    }
  }

  /**
@ -5508,7 +5506,7 @@ inline void gcode_M400() { st_synchronize(); }
    SERIAL_PROTOCOLLN(filament_width_meas);
  }

-#endif // FILAMENT_SENSOR
+#endif // FILAMENT_WIDTH_SENSOR

 /**
 * M410: Quickstop - Abort all planned moves
@ -6550,7 +6548,7 @@ void process_next_command() {
          break;
      #endif // AUTO_BED_LEVELING_FEATURE && (HAS_SERVO_ENDSTOPS || Z_PROBE_ALLEN_KEY) && !Z_PROBE_SLED

-      #if ENABLED(FILAMENT_SENSOR)
+      #if ENABLED(FILAMENT_WIDTH_SENSOR)
        case 404:  //M404 Enter the nominal filament width (3mm, 1.75mm ) N<3.0> or display nominal filament width
          gcode_M404();
          break;
@ -6563,7 +6561,7 @@ void process_next_command() {
        case 407:   //M407 Display measured filament diameter
          gcode_M407();
          break;
-      #endif // FILAMENT_SENSOR
+      #endif // ENABLED(FILAMENT_WIDTH_SENSOR)

      case 410: // M410 quickstop - Abort all the planned moves.
        gcode_M410();
--- a/Marlin/SanityCheck.h
+++ b/Marlin/SanityCheck.h
@ -169,9 +169,9 @@
 * Probes
 */

-  /**
-   * A probe needs a pin
-   */
+/**
+ * A probe needs a pin
+ */
 #if (!((HAS_Z_MIN && ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)) || HAS_Z_PROBE )) && ( ENABLED(FIX_MOUNTED_PROBE) || defined(Z_ENDSTOP_SERVO_NR) || ENABLED(Z_PROBE_ALLEN_KEY) || ENABLED(Z_PROBE_SLED))
  #error A probe needs a pin! [Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN || HAS_Z_PROBE]
 #endif
@ -180,9 +180,9 @@
  #error A probe should not be connected to more then one pin! [Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN || HAS_Z_PROBE]
 #endif

-  /**
-    * Require one kind of probe
-    */
+/**
+  * Require one kind of probe
+  */
 #if ENABLED(AUTO_BED_LEVELING_FEATURE) && !( ENABLED(FIX_MOUNTED_PROBE) || defined(Z_ENDSTOP_SERVO_NR) || ENABLED(Z_PROBE_ALLEN_KEY) || ENABLED(Z_PROBE_SLED))
  #error For AUTO_BED_LEVELING_FEATURE define one kind of probe! {Servo | Z_PROBE_ALLEN_KEY | Z_PROBE_SLED | FIX_MOUNTED_PROBE]
 #endif
@ -275,6 +275,14 @@

 #endif // AUTO_BED_LEVELING_FEATURE

+/**
+ * Filament Width Sensor
+ */
+#if ENABLED(FILAMENT_WIDTH_SENSOR) && !HAS_FILAMENT_WIDTH_SENSOR
+  #error FILAMENT_WIDTH_SENSOR requires a FILWIDTH_PIN to be defined.
+#endif
+
+
 /**
 * ULTIPANEL encoder
 */
@ -446,6 +454,8 @@
  #error SDEXTRASLOW deprecated - set SPI_SPEED to SPI_QUARTER_SPEED instead
 #elif defined(Z_RAISE_BEFORE_HOMING)
  #error Z_RAISE_BEFORE_HOMING is deprecated. Use MIN_Z_HEIGHT_FOR_HOMING instead.
+#elif defined(FILAMENT_SENSOR)
+  #error FILAMENT_SENSOR is deprecated. Use FILAMENT_WIDTH_SENSOR instead.
 #endif

 #endif //SANITYCHECK_H
--- a/Marlin/example_configurations/Felix/Configuration.h
+++ b/Marlin/example_configurations/Felix/Configuration.h
@ -903,11 +903,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 * Note may require analog pins to be defined for different motherboards
 **********************************************************************/
 // Uncomment below to enable
-//#define FILAMENT_SENSOR
+//#define FILAMENT_WIDTH_SENSOR

 #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  #define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
  #define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel

--- a/Marlin/example_configurations/Felix/Configuration_DUAL.h
+++ b/Marlin/example_configurations/Felix/Configuration_DUAL.h
@ -900,11 +900,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 * Note may require analog pins to be defined for different motherboards
 **********************************************************************/
 // Uncomment below to enable
-//#define FILAMENT_SENSOR
+//#define FILAMENT_WIDTH_SENSOR

 #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  #define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
  #define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel

--- a/Marlin/example_configurations/Hephestos/Configuration.h
+++ b/Marlin/example_configurations/Hephestos/Configuration.h
@ -915,11 +915,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 * Note may require analog pins to be defined for different motherboards
 **********************************************************************/
 // Uncomment below to enable
-//#define FILAMENT_SENSOR
+//#define FILAMENT_WIDTH_SENSOR

 #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  #define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
  #define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel

--- a/Marlin/example_configurations/Hephestos_2/Configuration.h
+++ b/Marlin/example_configurations/Hephestos_2/Configuration.h
@ -917,11 +917,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 * Note may require analog pins to be defined for different motherboards
 **********************************************************************/
 // Uncomment below to enable
-//#define FILAMENT_SENSOR
+//#define FILAMENT_WIDTH_SENSOR

 #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  #define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
  #define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel

--- a/Marlin/example_configurations/K8200/Configuration.h
+++ b/Marlin/example_configurations/K8200/Configuration.h
@ -937,11 +937,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 * Note may require analog pins to be defined for different motherboards
 **********************************************************************/
 // Uncomment below to enable
-//#define FILAMENT_SENSOR
+//#define FILAMENT_WIDTH_SENSOR

 #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  #define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
  #define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel

--- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
+++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
@ -920,11 +920,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 * Note may require analog pins to be defined for different motherboards
 **********************************************************************/
 // Uncomment below to enable
-//#define FILAMENT_SENSOR
+//#define FILAMENT_WIDTH_SENSOR

 #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  #define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
  #define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel

--- a/Marlin/example_configurations/RigidBot/Configuration.h
+++ b/Marlin/example_configurations/RigidBot/Configuration.h
@ -922,11 +922,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 * Note may require analog pins to be defined for different motherboards
 **********************************************************************/
 // Uncomment below to enable
-//#define FILAMENT_SENSOR
+//#define FILAMENT_WIDTH_SENSOR

 #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  #define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
  #define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel

--- a/Marlin/example_configurations/SCARA/Configuration.h
+++ b/Marlin/example_configurations/SCARA/Configuration.h
@ -928,11 +928,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 * Note may require analog pins to be defined for different motherboards
 **********************************************************************/
 // Uncomment below to enable
-//#define FILAMENT_SENSOR
+//#define FILAMENT_WIDTH_SENSOR

 #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  #define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
  #define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel

--- a/Marlin/example_configurations/TAZ4/Configuration.h
+++ b/Marlin/example_configurations/TAZ4/Configuration.h
@ -941,11 +941,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 * Note may require analog pins to be defined for different motherboards
 **********************************************************************/
 // Uncomment below to enable
-//#define FILAMENT_SENSOR
+//#define FILAMENT_WIDTH_SENSOR

 #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  #define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
  #define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel

--- a/Marlin/example_configurations/WITBOX/Configuration.h
+++ b/Marlin/example_configurations/WITBOX/Configuration.h
@ -912,11 +912,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 * Note may require analog pins to be defined for different motherboards
 **********************************************************************/
 // Uncomment below to enable
-//#define FILAMENT_SENSOR
+//#define FILAMENT_WIDTH_SENSOR

 #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  #define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
  #define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel

--- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h
+++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
@ -920,11 +920,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 * Note may require analog pins to be defined for different motherboards
 **********************************************************************/
 // Uncomment below to enable
-//#define FILAMENT_SENSOR
+//#define FILAMENT_WIDTH_SENSOR

 #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  #define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
  #define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel

--- a/Marlin/example_configurations/delta/biv2.5/Configuration.h
+++ b/Marlin/example_configurations/delta/biv2.5/Configuration.h
@ -1049,11 +1049,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 * Note may require analog pins to be defined for different motherboards
 **********************************************************************/
 // Uncomment below to enable
-//#define FILAMENT_SENSOR
+//#define FILAMENT_WIDTH_SENSOR

 #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  #define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
  #define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel

--- a/Marlin/example_configurations/delta/generic/Configuration.h
+++ b/Marlin/example_configurations/delta/generic/Configuration.h
@ -1049,11 +1049,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 * Note may require analog pins to be defined for different motherboards
 **********************************************************************/
 // Uncomment below to enable
-//#define FILAMENT_SENSOR
+//#define FILAMENT_WIDTH_SENSOR

 #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  #define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
  #define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel

--- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
@ -1053,11 +1053,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 * Note may require analog pins to be defined for different motherboards
 **********************************************************************/
 // Uncomment below to enable
-//#define FILAMENT_SENSOR
+//#define FILAMENT_WIDTH_SENSOR

 #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  #define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
  #define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel

--- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
@ -1046,11 +1046,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 * Note may require analog pins to be defined for different motherboards
 **********************************************************************/
 // Uncomment below to enable
-//#define FILAMENT_SENSOR
+//#define FILAMENT_WIDTH_SENSOR

 #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  #define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
  #define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel

--- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h
@ -956,11 +956,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 * Note may require analog pins to be defined for different motherboards
 **********************************************************************/
 // Uncomment below to enable
-//#define FILAMENT_SENSOR
+//#define FILAMENT_WIDTH_SENSOR

 #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  #define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
  #define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel

--- a/Marlin/example_configurations/makibox/Configuration.h
+++ b/Marlin/example_configurations/makibox/Configuration.h
@ -923,11 +923,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 * Note may require analog pins to be defined for different motherboards
 **********************************************************************/
 // Uncomment below to enable
-//#define FILAMENT_SENSOR
+//#define FILAMENT_WIDTH_SENSOR

 #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  #define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
  #define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel

--- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
@ -914,11 +914,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 * Note may require analog pins to be defined for different motherboards
 **********************************************************************/
 // Uncomment below to enable
-//#define FILAMENT_SENSOR
+//#define FILAMENT_WIDTH_SENSOR

 #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  #define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
  #define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel

--- a/Marlin/pins_A4JP.h
+++ b/Marlin/pins_A4JP.h
@ -74,10 +74,7 @@
  #endif
 #endif // VIKI2/miniVIKI

-#if ENABLED(FILAMENT_SENSOR)
-  //Filip added pin for Filament sensor analog input
-  #define FILWIDTH_PIN        3
-#endif
+#define FILWIDTH_PIN        3  // ANALOG NUMBERING

 /************************************************
 * Rambo pin assignments old
--- a/Marlin/pins_PRINTRBOARD.h
+++ b/Marlin/pins_PRINTRBOARD.h
@ -79,9 +79,7 @@
 #define TEMP_0_PIN          1  // Extruder / Analog pin numbering
 #define TEMP_BED_PIN        0  // Bed / Analog pin numbering

-#if ENABLED(FILAMENT_SENSOR)
-  #define FILWIDTH_PIN      2
-#endif
+#define FILWIDTH_PIN        2  // ANALOG NUMBERING

 #define TEMP_1_PIN         -1
 #define TEMP_2_PIN         -1
--- a/Marlin/pins_PRINTRBOARD_REVF.h
+++ b/Marlin/pins_PRINTRBOARD_REVF.h
@ -73,9 +73,7 @@
 #define TEMP_0_PIN          1  // Extruder / Analog pin numbering
 #define TEMP_BED_PIN        0  // Bed / Analog pin numbering

-#if ENABLED(FILAMENT_SENSOR)
-  #define FILWIDTH_PIN      2
-#endif
+#define FILWIDTH_PIN        2  // ANALOG NUMBERING

 #define TEMP_1_PIN         -1
 #define TEMP_2_PIN         -1
--- a/Marlin/pins_RAMBO.h
+++ b/Marlin/pins_RAMBO.h
@ -112,6 +112,8 @@
 #define LED_PIN            13
 #define FAN_PIN            8

+#define FILWIDTH_PIN        3  // ANALOG NUMBERING
+
 /**********************************************************
  Fan Pins
  Fan_0 8
@ -201,7 +203,3 @@
  #endif
 #endif // VIKI2/miniVIKI

-#if ENABLED(FILAMENT_SENSOR)
-  //Filip added pin for Filament sensor analog input
-  #define FILWIDTH_PIN        3
-#endif
--- a/Marlin/pins_RAMPS_14.h
+++ b/Marlin/pins_RAMPS_14.h
@ -91,11 +91,8 @@
 #define SDSS               53
 #define LED_PIN            13

-#if ENABLED(FILAMENT_SENSOR)  // FMM added for Filament Extruder
-  // define analog pin for the filament width sensor input
-  // Use the RAMPS 1.4 Analog input 5 on the AUX2 connector
-  #define FILWIDTH_PIN      5
-#endif
+// Use the RAMPS 1.4 Analog input 5 on the AUX2 connector
+#define FILWIDTH_PIN        5 // ANALOG NUMBERING

 #if ENABLED(Z_MIN_PROBE_ENDSTOP)
  // Define a pin to use as the signal pin on Arduino for the Z_PROBE endstop.
--- a/Marlin/planner.cpp
+++ b/Marlin/planner.cpp
@ -851,7 +851,7 @@ float junction_deviation = 0.1;
  block->nominal_speed = block->millimeters * inverse_second; // (mm/sec) Always > 0
  block->nominal_rate = ceil(block->step_event_count * inverse_second); // (step/sec) Always > 0

-  #if ENABLED(FILAMENT_SENSOR)
+  #if ENABLED(FILAMENT_WIDTH_SENSOR)
    //FMM update ring buffer used for delay with filament measurements
    if (extruder == FILAMENT_SENSOR_EXTRUDER_NUM && delay_index2 > -1) {  //only for extruder with filament sensor and if ring buffer is initialized

--- a/Marlin/temperature.cpp
+++ b/Marlin/temperature.cpp
@ -93,7 +93,7 @@ unsigned char soft_pwm_bed;
  volatile int babystepsTodo[3] = { 0 };
 #endif

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  int current_raw_filwidth = 0;  //Holds measured filament diameter - one extruder only
 #endif

@ -209,7 +209,7 @@ static void updateTemperaturesFromRawValues();
  #define SOFT_PWM_SCALE 0
 #endif

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  static int meas_shift_index;  //used to point to a delayed sample in buffer for filament width sensor
 #endif

@ -703,7 +703,7 @@ void manage_heater() {
  #endif

  // Control the extruder rate based on the width sensor
-  #if ENABLED(FILAMENT_SENSOR)
+  #if ENABLED(FILAMENT_WIDTH_SENSOR)
    if (filament_sensor) {
      meas_shift_index = delay_index1 - meas_delay_cm;
      if (meas_shift_index < 0) meas_shift_index += MAX_MEASUREMENT_DELAY + 1;  //loop around buffer if needed
@ -715,7 +715,7 @@ void manage_heater() {
      NOLESS(vm, 0.01);
      volumetric_multiplier[FILAMENT_SENSOR_EXTRUDER_NUM] = vm;
    }
-  #endif //FILAMENT_SENSOR
+  #endif //FILAMENT_WIDTH_SENSOR

  #if DISABLED(PIDTEMPBED)
    if (ms < next_bed_check_ms) return;
@ -849,7 +849,7 @@ static void updateTemperaturesFromRawValues() {
  #if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT)
    redundant_temperature = analog2temp(redundant_temperature_raw, 1);
  #endif
-  #if HAS_FILAMENT_SENSOR
+  #if ENABLED(FILAMENT_WIDTH_SENSOR)
    filament_width_meas = analog2widthFil();
  #endif

@ -864,7 +864,7 @@ static void updateTemperaturesFromRawValues() {
 }


-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)

  // Convert raw Filament Width to millimeters
  float analog2widthFil() {
@ -1003,7 +1003,7 @@ void tp_init() {
  #if HAS_TEMP_BED
    ANALOG_SELECT(TEMP_BED_PIN);
  #endif
-  #if HAS_FILAMENT_SENSOR
+  #if ENABLED(FILAMENT_WIDTH_SENSOR)
    ANALOG_SELECT(FILWIDTH_PIN);
  #endif

@ -1354,7 +1354,7 @@ ISR(TIMER0_COMPB_vect) {
    ISR_STATICS(BED);
  #endif

-  #if HAS_FILAMENT_SENSOR
+  #if ENABLED(FILAMENT_WIDTH_SENSOR)
    static unsigned long raw_filwidth_value = 0;
  #endif

@ -1636,14 +1636,14 @@ ISR(TIMER0_COMPB_vect) {
      break;

    case Prepare_FILWIDTH:
-      #if HAS_FILAMENT_SENSOR
+      #if ENABLED(FILAMENT_WIDTH_SENSOR)
        START_ADC(FILWIDTH_PIN);
      #endif
      lcd_buttons_update();
      temp_state = Measure_FILWIDTH;
      break;
    case Measure_FILWIDTH:
-      #if HAS_FILAMENT_SENSOR
+      #if ENABLED(FILAMENT_WIDTH_SENSOR)
        // raw_filwidth_value += ADC;  //remove to use an IIR filter approach
        if (ADC > 102) { //check that ADC is reading a voltage > 0.5 volts, otherwise don't take in the data.
          raw_filwidth_value -= (raw_filwidth_value >> 7); //multiply raw_filwidth_value by 127/128
@ -1669,7 +1669,7 @@ ISR(TIMER0_COMPB_vect) {
    if (!temp_meas_ready) set_current_temp_raw();

    // Filament Sensor - can be read any time since IIR filtering is used
-    #if HAS_FILAMENT_SENSOR
+    #if ENABLED(FILAMENT_WIDTH_SENSOR)
      current_raw_filwidth = raw_filwidth_value >> 10;  // Divide to get to 0-16384 range since we used 1/128 IIR filter approach
    #endif

--- a/Marlin/temperature.h
+++ b/Marlin/temperature.h
@ -53,7 +53,7 @@
 void tp_init();  //initialize the heating
 void manage_heater(); //it is critical that this is called periodically.

-#if ENABLED(FILAMENT_SENSOR)
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
  // For converting raw Filament Width to milimeters
  float analog2widthFil();