Fix G26 Circle Drawing. Add Default Extrusion Settings (#8313)

- Fix G26 Circle Drawing.
- Add default extrusion settings so machine can print lines on print bed
- Yet to be done: Get LCD Menu's to use these settings.

Marlin/Configuration.h

@@ -1685,6 +1685,18 @@
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 // Servo deactivation
 //
 // With this option servos are powered only during movement, then turned off to prevent jitter.
@@ -1710,8 +1722,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/Configuration_adv.h

@@ -256,6 +256,29 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Dual X Steppers
+// Uncomment this option to drive two X axis motors.
+// The next unused E driver will be assigned to the second X stepper.
+//#define X_DUAL_STEPPER_DRIVERS
+#if ENABLED(X_DUAL_STEPPER_DRIVERS)
+  // Set true if the two X motors need to rotate in opposite directions
+  #define INVERT_X2_VS_X_DIR true
+#endif
+
+// Dual Y Steppers
+// Uncomment this option to drive two Y axis motors.
+// The next unused E driver will be assigned to the second Y stepper.
+//#define Y_DUAL_STEPPER_DRIVERS
+#if ENABLED(Y_DUAL_STEPPER_DRIVERS)
+  // Set true if the two Y motors need to rotate in opposite directions
+  #define INVERT_Y2_VS_Y_DIR true
+#endif
+
+// A single Z stepper driver is usually used to drive 2 stepper motors.
+// Uncomment this option to use a separate stepper driver for each Z axis motor.
+// The next unused E driver will be assigned to the second Z stepper.
+//#define Z_DUAL_STEPPER_DRIVERS
+
 /**
  * Dual Steppers / Dual Endstops
  *

Marlin/src/config/default/Configuration.h

@@ -1685,6 +1685,18 @@
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 // Servo deactivation
 //
 // With this option servos are powered only during movement, then turned off to prevent jitter.
@@ -1710,8 +1722,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h

@@ -1710,6 +1710,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1730,8 +1742,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/AliExpress/CL-260/Configuration.h

@@ -1690,6 +1690,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1710,8 +1722,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/Anet/A6/Configuration.h

@@ -1849,6 +1849,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1869,8 +1881,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/Anet/A8/Configuration.h

@@ -1693,6 +1693,18 @@
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 // Servo deactivation
 //
 // With this option servos are powered only during movement, then turned off to prevent jitter.
@@ -1718,8 +1730,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/Azteeg/X5GT/Configuration.h

@@ -1680,6 +1680,18 @@
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 // Servo deactivation
 //
 // With this option servos are powered only during movement, then turned off to prevent jitter.
@@ -1705,8 +1717,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/BQ/Hephestos/Configuration.h

@@ -1681,6 +1681,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1701,8 +1713,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h

@@ -1691,6 +1691,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1711,8 +1723,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/BQ/WITBOX/Configuration.h

@@ -1681,6 +1681,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1701,8 +1713,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/Cartesio/Configuration.h

@@ -1689,6 +1689,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1709,8 +1721,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/Creality/CR-10/Configuration.h

@@ -1700,6 +1700,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1720,7 +1732,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
 #define DEFAULT_STDDEV_FILAMENT_DIA 0.05    // Typical estimate for cheap filament
 //#define DEFAULT_STDDEV_FILAMENT_DIA 0.02  // Typical advertised for higher quality filament
 

Marlin/src/config/examples/Felix/Configuration.h

@@ -1667,6 +1667,18 @@
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 // Servo deactivation
 //
 // With this option servos are powered only during movement, then turned off to prevent jitter.
@@ -1692,8 +1704,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/Felix/DUAL/Configuration.h

@@ -1672,6 +1672,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1692,8 +1704,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h

@@ -1682,6 +1682,18 @@
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 500 }
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 // Servo deactivation
 //
 // With this option servos are powered only during movement, then turned off to prevent jitter.
@@ -1707,8 +1719,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/Geeetech/GT2560/Configuration.h

@@ -1700,6 +1700,18 @@
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 // Servo deactivation
 //
 // With this option servos are powered only during movement, then turned off to prevent jitter.
@@ -1725,8 +1737,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

@@ -1690,6 +1690,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1710,8 +1722,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/Infitary/i3-M508/Configuration.h

@@ -1689,6 +1689,18 @@
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 // Servo deactivation
 //
 // With this option servos are powered only during movement, then turned off to prevent jitter.
@@ -1714,8 +1726,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/Malyan/M150/Configuration.h

@@ -1713,6 +1713,18 @@
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 // Servo deactivation
 //
 // With this option servos are powered only during movement, then turned off to prevent jitter.
@@ -1738,8 +1750,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/Micromake/C1/basic/Configuration.h

@@ -1694,6 +1694,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1714,8 +1726,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h

@@ -1694,6 +1694,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1714,8 +1726,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/Mks/Sbase/Configuration.h

@@ -1660,6 +1660,18 @@
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 // Servo deactivation
 //
 // With this option servos are powered only during movement, then turned off to prevent jitter.
@@ -1685,8 +1697,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h

@@ -1690,6 +1690,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1710,8 +1722,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/RigidBot/Configuration.h

@@ -1690,6 +1690,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1710,8 +1722,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/SCARA/Configuration.h

@@ -1702,6 +1702,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1722,8 +1734,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/STM32F10/Configuration.h

@@ -1693,6 +1693,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1713,8 +1725,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/Sanguinololu/Configuration.h

@@ -1716,6 +1716,18 @@
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 // Servo deactivation
 //
 // With this option servos are powered only during movement, then turned off to prevent jitter.
@@ -1741,8 +1753,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/TinyBoy2/Configuration.h

@@ -1746,6 +1746,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1766,8 +1778,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h

@@ -1686,6 +1686,18 @@
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 // Servo deactivation
 //
 // With this option servos are powered only during movement, then turned off to prevent jitter.
@@ -1711,8 +1723,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/Velleman/K8200/Configuration.h

@@ -1720,6 +1720,18 @@
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 // Servo deactivation
 //
 // With this option servos are powered only during movement, then turned off to prevent jitter.
@@ -1745,8 +1757,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/Velleman/K8400/Configuration.h

@@ -1690,6 +1690,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1710,8 +1722,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h

@@ -1685,6 +1685,18 @@
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 // Servo deactivation
 //
 // With this option servos are powered only during movement, then turned off to prevent jitter.
@@ -1710,8 +1722,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/adafruit/ST7565/Configuration.h

@@ -1690,6 +1690,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1710,8 +1722,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h

@@ -1824,6 +1824,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1844,8 +1856,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h

@@ -1817,6 +1817,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1837,8 +1849,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/delta/generic/Configuration.h

@@ -1812,6 +1812,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1832,8 +1844,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/delta/kossel_mini/Configuration.h

@@ -1815,6 +1815,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1835,8 +1847,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/delta/kossel_pro/Configuration.h

@@ -1810,6 +1810,18 @@
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 // Servo deactivation
 //
 // With this option servos are powered only during movement, then turned off to prevent jitter.
@@ -1835,8 +1847,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/delta/kossel_xl/Configuration.h

@@ -1824,6 +1824,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1844,8 +1856,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h

@@ -1704,6 +1704,18 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 /**
  * Filament Width Sensor
  *
@@ -1724,8 +1736,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/makibox/Configuration.h

@@ -1688,6 +1688,18 @@
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 // Servo deactivation
 //
 // With this option servos are powered only during movement, then turned off to prevent jitter.
@@ -1713,8 +1725,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/tvrrug/Round2/Configuration.h

@@ -1680,6 +1680,18 @@
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 // Servo deactivation
 //
 // With this option servos are powered only during movement, then turned off to prevent jitter.
@@ -1705,8 +1717,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/config/examples/wt150/Configuration.h

@@ -1690,6 +1690,18 @@
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }
 
+/**
+ * Default extrusion settings
+ *
+ * These settings control basic extrusion from within the Marlin firmware.
+ * 
+ */
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+#define DEFAULT_NOZZLE_SIZE           .4    // (mm) Diameter of primary nozzle.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_LAYER_HEIGHT          .2    // (mm) Default layer height that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_HOTEND_TEMP        205.0    // (c)  Default nozzle temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+#define DEFAULT_BED_TEMP            60.0    // (c)  Default bed temperature that will produce usable results by the printer.  Used by G26 Mesh Validation Pattern tool.
+
 // Servo deactivation
 //
 // With this option servos are powered only during movement, then turned off to prevent jitter.
@@ -1715,8 +1727,6 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
   #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber

Marlin/src/feature/bedlevel/ubl/G26_Mesh_Validation_Tool.cpp

@@ -41,12 +41,7 @@
 
 #define EXTRUSION_MULTIPLIER 1.0
 #define RETRACTION_MULTIPLIER 1.0
-#define NOZZLE 0.4
-#define FILAMENT 1.75
-#define LAYER_HEIGHT 0.2
 #define PRIME_LENGTH 10.0
-#define BED_TEMP 60.0
-#define HOTEND_TEMP 205.0
 #define OOZE_AMOUNT 0.3
 
 #define SIZE_OF_INTERSECTION_CIRCLES 5
@@ -623,12 +618,12 @@ bool unified_bed_leveling::parse_G26_parameters() {
 
   g26_extrusion_multiplier  = EXTRUSION_MULTIPLIER;
   g26_retraction_multiplier = RETRACTION_MULTIPLIER;
-  g26_nozzle                = NOZZLE;
+  g26_nozzle                = DEFAULT_NOZZLE_SIZE;
-  g26_filament_diameter     = FILAMENT;
+  g26_filament_diameter     = DEFAULT_NOMINAL_FILAMENT_DIA;
-  g26_layer_height          = LAYER_HEIGHT;
+  g26_layer_height          = DEFAULT_LAYER_HEIGHT;
   g26_prime_length          = PRIME_LENGTH;
-  g26_bed_temp              = BED_TEMP;
+  g26_bed_temp              = DEFAULT_BED_TEMP;
-  g26_hotend_temp           = HOTEND_TEMP;
+  g26_hotend_temp           = DEFAULT_HOTEND_TEMP;
   g26_prime_flag            = 0;
 
   g26_ooze_amount           = parser.linearval('O', OOZE_AMOUNT);

Marlin/src/module/motion.cpp

@@ -638,25 +638,30 @@ float soft_endstop_min[XYZ] = { X_MIN_BED, Y_MIN_BED, Z_MIN_POS },
    *
    * Returns true if current_position[] was set to destination[]
    */
+
   inline bool prepare_move_to_destination_cartesian() {
-    if (current_position[X_AXIS] != destination[X_AXIS] || current_position[Y_AXIS] != destination[Y_AXIS]) {
+    const float fr_scaled = MMS_SCALED(feedrate_mm_s);
-      const float fr_scaled = MMS_SCALED(feedrate_mm_s);
       #if HAS_MESH
-        if (planner.leveling_active) {
+        if (!planner.leveling_active) {
-          #if ENABLED(AUTO_BED_LEVELING_UBL)
+          line_to_destination(fr_scaled);
-            ubl.line_to_destination_cartesian(fr_scaled, active_extruder);
+          return false;
-          #elif ENABLED(MESH_BED_LEVELING)
-            mesh_line_to_destination(fr_scaled);
-          #elif ENABLED(AUTO_BED_LEVELING_BILINEAR)
-            bilinear_line_to_destination(fr_scaled);
-          #endif
-          return true;
         }
+        #if ENABLED(AUTO_BED_LEVELING_UBL)
+          ubl.line_to_destination_cartesian(fr_scaled, active_extruder);  // UBL's motion routine needs to know about all moves,
+          return true;                                                    // even purely Z-Axis moves
+        #else
+          if (current_position[X_AXIS] != destination[X_AXIS] || current_position[Y_AXIS] != destination[Y_AXIS]) {
+            #if ENABLED(MESH_BED_LEVELING)
+              mesh_line_to_destination(fr_scaled);
+            #elif ENABLED(AUTO_BED_LEVELING_BILINEAR)
+              bilinear_line_to_destination(fr_scaled);
+            #endif
+            return true;
+          }
+          else
+            line_to_destination();
+        #endif
       #endif // HAS_MESH
-      line_to_destination(fr_scaled);
-    }
-    else
-      line_to_destination();
 
     return false;
   }