Bring Sidewinder X1 config up to date (#14271)

config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration.h

@@ -137,7 +137,7 @@
 
 // Optional custom name for your RepStrap or other custom machine
 // Displayed in the LCD "Ready" message
-//#define CUSTOM_MACHINE_NAME "Sidewinder X1"
+#define CUSTOM_MACHINE_NAME "Sidewinder X1"
 
 // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
 // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
@@ -359,6 +359,7 @@
  *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  *    15 : 100k thermistor calibration for JGAurora A5 hotend
+ *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
  *    20 : the PT100 circuit found in the Ultimainboard V2.x
  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
@@ -384,7 +385,7 @@
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  *
- * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" }
+ * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" }
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
@@ -511,6 +512,12 @@
   #define DEFAULT_bedKi 45.87
   #define DEFAULT_bedKd 325.08
 
+  //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+  //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
+  //#define DEFAULT_bedKp 10.00
+  //#define DEFAULT_bedKi .023
+  //#define DEFAULT_bedKd 305.4
+
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
   //#define DEFAULT_bedKp 97.1
@@ -826,16 +833,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  //#define BLTOUCH_DELAY 500   // Minimum Command delay (ms). Enable and increase if needed
-
-  /**
-   * BLTouch V3.0 and newer smart series
-   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
-   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
-   */
-  //#define BLTOUCH_FORCE_5V_MODE
-#endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h

@@ -375,17 +375,14 @@
   #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
   #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
   #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
-  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+  //#define CASE_LIGHT_MENU                   // Add Case Light options to the LCD menu
+  //#define CASE_LIGHT_NO_BRIGHTNESS          // Disable brightness control. Enable for non-PWM lighting.
   //#define CASE_LIGHT_USE_NEOPIXEL           // Use Neopixel LED as case light, requires NEOPIXEL_LED.
   #if ENABLED(CASE_LIGHT_USE_NEOPIXEL)
     #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White }
   #endif
 #endif
 
-//===========================================================================
-//============================ Mechanical Settings ==========================
-//===========================================================================
-
 // @section homing
 
 // If you want endstops to stay on (by default) even when not homing
@@ -527,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.
@@ -577,8 +641,11 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 2*60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
 #if ENABLED(ULTIPANEL)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif
@@ -851,7 +918,7 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
-    //#define POWER_LOSS_PIN         44 // Pin to detect power loss (optional)
+    //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PURGE_LEN   20 // (mm) Length of filament to purge on resume
     //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
@@ -913,7 +980,7 @@
    * This feature must be enabled with "M540 S1" or from the LCD menu.
    * To have any effect, endstops must be enabled during SD printing.
    */
-  //#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
+  //#define SD_ABORT_ON_ENDSTOP_HIT
 
   /**
    * This option makes it easier to print the same SD Card file again.
@@ -1043,6 +1110,7 @@
   #define STATUS_HOTEND_INVERTED      // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM)
   #define STATUS_HOTEND_ANIM          // Use a second bitmap to indicate hotend heating
   #define STATUS_BED_ANIM             // Use a second bitmap to indicate bed heating
+  #define STATUS_CHAMBER_ANIM         // Use a second bitmap to indicate chamber heating
   //#define STATUS_ALT_BED_BITMAP     // Use the alternative bed bitmap
   //#define STATUS_ALT_FAN_BITMAP     // Use the alternative fan bitmap
   //#define STATUS_FAN_FRAMES 3       // :[0,1,2,3,4] Number of fan animation frames
@@ -1129,7 +1197,7 @@
 #define LIN_ADVANCE
 #if ENABLED(LIN_ADVANCE)
   //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants
-  #define LIN_ADVANCE_K 0.08    // Unit: mm compression per 1mm/s extruder speed
+  #define LIN_ADVANCE_K 0.0    // Unit: mm compression per 1mm/s extruder speed
   //#define LA_DEBUG            // If enabled, this will generate debug information output over USB.
 #endif
 
@@ -1763,6 +1831,12 @@
     //#define Z_STALL_SENSITIVITY  8
   #endif
 
+  /**
+   * Beta feature!
+   * Create a 50/50 square wave step pulse optimal for stepper drivers.
+   */
+  //#define SQUARE_WAVE_STEPPING
+
   /**
    * Enable M122 debugging command for TMC stepper drivers.
    * M122 S0/1 will enable continous reporting.