zaubentrucker/muele-marlin
1
0
Fork 0
Code Issues Pull requests Actions Packages Projects Releases Wiki Activity

SPINDLE/LASER pins changes

Browse source
This commit is contained in:
Scott Lahteine 2017-04-07 13:52:21 -05:00 committed by Scott Lahteine
parent 99c4900a98
commit ffe0e2d19a
41 changed files with 1247 additions and 110 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

4
Marlin/pinsDebug_list.h
View file

@ -515,8 +515,8 @@
#if PIN_EXISTS(SPINDLE_LASER_ENABLE) #if PIN_EXISTS(SPINDLE_LASER_ENABLE)
REPORT_NAME_DIGITAL(SPINDLE_LASER_ENABLE_PIN, __LINE__ ) REPORT_NAME_DIGITAL(SPINDLE_LASER_ENABLE_PIN, __LINE__ )
#endif #endif
#if PIN_EXISTS(SPINDLE_SPEED_LASER_POWER) #if PIN_EXISTS(SPINDLE_LASER_PWM)
REPORT_NAME_DIGITAL(SPINDLE_SPEED_LASER_POWER_PIN, __LINE__ ) REPORT_NAME_DIGITAL(SPINDLE_LASER_PWM_PIN, __LINE__ )
#endif #endif
#if PIN_EXISTS(SR_CLK) #if PIN_EXISTS(SR_CLK)
REPORT_NAME_DIGITAL(SR_CLK_PIN, __LINE__ ) REPORT_NAME_DIGITAL(SR_CLK_PIN, __LINE__ )

57
Marlin/pins_3DRAG.h
View file

@ -43,6 +43,8 @@
#define RAMPS_D9_PIN 8 #define RAMPS_D9_PIN 8
#define MOSFET_D_PIN 12 #define MOSFET_D_PIN 12
#define CASE_LIGHT_PIN -1 // MUST BE HARDWARE PWM but one is not available on expansion header
#include "pins_RAMPS.h" #include "pins_RAMPS.h"
// //
@ -104,3 +106,58 @@
#define BEEPER_PIN 33 #define BEEPER_PIN 33
#endif // ULTRA_LCD && NEWPANEL #endif // ULTRA_LCD && NEWPANEL
/**
* M3/M4/M5 - Spindle/Laser Control
*
* If you want to control the speed of your spindle then you'll have
* have to sacrifce the Extruder and pull some signals off the Z stepper
* driver socket.
*
* The following assumes:
* - the Z stepper driver socket is empty
* - the extruder driver socket has a driver board plugged into it
* - the Z stepper wires are attached the the extruder connector
*
* If you want to keep the extruder AND don't have a LCD display then
* you can still control the power on/off and spindle direction.
*
* Where to get spindle signals
*
* stepper signal socket name socket name
* -------
* SPINDLE_LASER_ENABLE_PIN /ENABLE O| |O VMOT
* MS1 O| |O GND
* MS2 O| |O 2B
* MS3 O| |O 2A
* /RESET O| |O 1A
* /SLEEP O| |O 1B
* SPINDLE_LASER_PWM_PIN STEP O| |O VDD
* SPINDLE_DIR_PIN DIR O| |O GND
* -------
*
* Note: Socket names vary from vendor to vendor
*/
#undef SPINDLE_LASER_PWM_PIN // Definitions in pins_RAMPS.h are not good with 3DRAG
#undef SPINDLE_LASER_ENABLE_PIN
#undef SPINDLE_DIR_PIN
#if ENABLED(SPINDLE_LASER_ENABLE)
#if !EXTRUDERS
#undef E0_DIR_PIN
#undef E0_ENABLE_PIN
#undef E0_STEP_PIN
#undef Z_DIR_PIN
#undef Z_ENABLE_PIN
#undef Z_STEP_PIN
#define Z_DIR_PIN 28
#define Z_ENABLE_PIN 24
#define Z_STEP_PIN 26
#define SPINDLE_LASER_PWM_PIN 46 // MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 62 // Pin should have a pullup!
#define SPINDLE_DIR_PIN 48
#elif !(ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)) // use expansion header if no LCD in use
#define SPINDLE_LASER_ENABLE_PIN 16 // Pin should have a pullup/pulldown!
#define SPINDLE_DIR_PIN 17
#endif
#endif

35
Marlin/pins_AZTEEG_X3.h
View file

@ -24,12 +24,20 @@
* AZTEEG_X3 Arduino Mega with RAMPS v1.4 pin assignments * AZTEEG_X3 Arduino Mega with RAMPS v1.4 pin assignments
*/ */
#ifndef __AVR_ATmega2560__
#error "Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu."
#endif
#if HOTENDS > 2 || E_STEPPERS > 2 #if HOTENDS > 2 || E_STEPPERS > 2
#error "Azteeg X3 supports up to 2 hotends / E-steppers. Comment out this line to continue." #error "Azteeg X3 supports up to 2 hotends / E-steppers. Comment out this line to continue."
#endif #endif
#define BOARD_NAME "Azteeg X3" #define BOARD_NAME "Azteeg X3"
#if !PIN_EXISTS(CASE_LIGHT) // doesn't already exist so OK to change the definition coming
#define OK_TO_CHANGE_CASE_LIGHT // in from from the include file
#endif
#include "pins_RAMPS_13.h" #include "pins_RAMPS_13.h"
// //
@ -63,3 +71,30 @@
#define STAT_LED_BLUE_PIN 11 #define STAT_LED_BLUE_PIN 11
#endif #endif
//
// Misc
//
#if ENABLED(OK_TO_CHANGE_CASE_LIGHT) && STAT_LED_RED_PIN == 6
#undef STAT_LED_RED_PIN
#undef CASE_LIGHT_PIN
#define CASE_LIGHT_PIN 6 // open collector FET driver
#endif
//
// M3/M4/M5 - Spindle/Laser Control
//
#undef SPINDLE_LASER_PWM_PIN // Definitions in pins_RAMPS.h are no good with the AzteegX3 board
#undef SPINDLE_LASER_ENABLE_PIN
#undef SPINDLE_DIR_PIN
#if ENABLED(SPINDLE_LASER_ENABLE)
#undef SDA // use EXP3 header
#undef SCL
#if SERVO0_PIN == 7
#undef SERVO0_PIN
#def SERVO0_PIN 11
#define SPINDLE_LASER_PWM_PIN 7 // MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 20 // Pin should have a pullup!
#define SPINDLE_DIR_PIN 21
#endif

38
Marlin/pins_AZTEEG_X3_PRO.h
View file

@ -30,8 +30,16 @@
#define BOARD_NAME "Azteeg X3 Pro" #define BOARD_NAME "Azteeg X3 Pro"
#if !PIN_EXISTS(CASE_LIGHT) // doesn't already exist so OK to change the definition coming
#define OK_TO_CHANGE_CASE_LIGHT // in from from the include file
#endif
#include "pins_RAMPS.h" #include "pins_RAMPS.h"
#ifndef __AVR_ATmega2560__
#error "Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu."
#endif
// //
// Servos // Servos
// //
@ -126,7 +134,37 @@
#if ENABLED(VIKI2) || ENABLED(miniVIKI) #if ENABLED(VIKI2) || ENABLED(miniVIKI)
#undef SD_DETECT_PIN #undef SD_DETECT_PIN
#define SD_DETECT_PIN 49 // For easy adapter board #define SD_DETECT_PIN 49 // For easy adapter board
#undef BEEPER_PIN
#define BEEPER_PIN 12 // 33 isn't physically available to the LCD display
#else #else
#define STAT_LED_RED_PIN 32 #define STAT_LED_RED_PIN 32
#define STAT_LED_BLUE_PIN 35 #define STAT_LED_BLUE_PIN 35
#endif #endif
//
// Misc. Functions
//
#undef DOGLCD_A0 // steal pin 44 for the case light
#define DOGLCD_A0 57
#if ENABLED(OK_TO_CHANGE_CASE_LIGHT)
#undef CASE_LIGHT_PIN
#define CASE_LIGHT_PIN 44 // must have a hardware PWM
#endif
//
// M3/M4/M5 - Spindle/Laser Control
//
#undef SPINDLE_LASER_PWM_PIN // Definitions in pins_RAMPS.h are no good with the AzteegX3 board
#undef SPINDLE_LASER_ENABLE_PIN
#undef SPINDLE_DIR_PIN
#if ENABLED(SPINDLE_LASER_ENABLE) // use EXP2 header
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
#undef BTN_EN2
#define BTN_EN2 31 // need 7 for the spindle speed PWM
#endif
#define SPINDLE_LASER_PWM_PIN 7 // must have a hardware PWM
#define SPINDLE_LASER_ENABLE_PIN 20 // Pin should have a pullup!
#define SPINDLE_DIR_PIN 21
#endif

7
Marlin/pins_BAM_DICE_DUE.h
View file

@ -30,6 +30,13 @@
#define BOARD_NAME "2PrintBeta Due" #define BOARD_NAME "2PrintBeta Due"
//
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_ENABLE_PIN 66 // Pin should have a pullup/pulldown!
#define SPINDLE_DIR_PIN 67
#define SPINDLE_LASER_PWM_PIN 44 // MUST BE HARDWARE PWM
#include "pins_RAMPS.h" #include "pins_RAMPS.h"
// //

12
Marlin/pins_BQ_ZUM_MEGA_3D.h
View file

@ -46,6 +46,18 @@
#define ORIG_E2_AUTO_FAN_PIN 6 #define ORIG_E2_AUTO_FAN_PIN 6
#define ORIG_E3_AUTO_FAN_PIN 6 #define ORIG_E3_AUTO_FAN_PIN 6
//
// Misc. Functions
//
#define CASE_LIGHT_PIN 44 // MUST BE HARDWARE PWM
//
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_ENABLE_PIN 40 // Pin should have a pullup/pulldown!
#define SPINDLE_LASER_PWM_PIN 44 // MUST BE HARDWARE PWM
#define SPINDLE_DIR_PIN 42
#include "pins_RAMPS_13.h" #include "pins_RAMPS_13.h"
// //

34
Marlin/pins_BRAINWAVE.h
View file

@ -27,6 +27,40 @@
* https://github.com/unrepentantgeek/brainwave-arduino * https://github.com/unrepentantgeek/brainwave-arduino
*/ */
/**
* Rev B 16 JAN 2017
*
* Added pointer to a currently available Arduino IDE extension that will
* allow this board to use the latest Marlin software
*/
/**
* Marlin_AT90USB - https://github.com/Bob-the-Kuhn/Marlin_AT90USB
* This is the only known IDE extension that is compatible with the pin definitions
* in this file, Adrduino 1.6.12 and the latest mainstream Marlin software.
*
* "Marlin_AT90USB" makes PWM0A available rather than the usual PWM1C. These PWMs share
* the same physical pin. Marlin uses TIMER1 to generate interrupts and sets it up such
* that PWM1A, PWM1B & PWM1C can not be used.
*
* Installation:
*
* 1. In the Arduino IDE, under Files -> Preferences paste the following URL
* https://rawgit.com/Bob-the-Kuhn/Marlin_AT90USB/master/package_MARLIN_AT90USB_index.json
* 2. Under Tools -> Board -> Boards manager, scroll to the bottom, click on MARLIN_AT90USB
* and then click on "Install"
* 3. Select "AT90USB646_STANDARD" from the 'Tools -> Boards' menu.
*/
/**
* To burn the bootloader that comes with Marlin_AT90USB:
*
* 1. Connect your programmer to the board.
* 2. In Arduino IDE select "AT90USB646_STANDARD" and then select the programmer.
* 3. In Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message.
* 4. The programmer is no longer needed. Remove it.
*/
#ifndef __AVR_AT90USB646__ #ifndef __AVR_AT90USB646__
#error "Oops! Make sure you have 'Brainwave' selected from the 'Tools -> Boards' menu." #error "Oops! Make sure you have 'Brainwave' selected from the 'Tools -> Boards' menu."
#endif #endif

60
Marlin/pins_BRAINWAVE_PRO.h
View file

@ -27,14 +27,70 @@
* https://github.com/unrepentantgeek/brainwave-arduino * https://github.com/unrepentantgeek/brainwave-arduino
*/ */
/**
* Rev B 16 JAN 2017
*
* Added pointers to currently available Arduino IDE extensions that will
* allow this board to use the latest Marlin software
*/
/**
* There are three Arduino IDE extensions that are compatible with this board
* and with the mainstream Marlin software. All have been used with Arduino 1.6.12
*
* Teensyduino - http://www.pjrc.com/teensy/teensyduino.html
* Select Teensy++ 2.0 in Arduino IDE from the 'Tools -> Boards' menu
*
* Installation instructions are at the above URL. Don't bother loading the
* libraries - they are not used with the Marlin software.
*
* Printrboard - https://github.com/scwimbush/Printrboard-HID-Arduino-IDE-Support
* This is basically Teensyduino but with a bootloader that can handle image sizes
* larger than 64K.
*
* Installation:
*
* 1. Go to the above URL, click on the "Clone or Download" button and then
* click on "Download ZIP" button.
* 2. Unzip the file, find the "printrboard" directory and then copy it to the
* hardware directory in Arduino. The Arduino hardware directory will probably
* be located in a path similar to this: C:\Program Files (x86)\Arduino\hardware.
* 3. Restart Arduino.
* 4. Select "Printrboard" from the 'Tools -> Boards' menu.
*
* Marlin_AT90USB - https://github.com/Bob-the-Kuhn/Marlin_AT90USB
* Uses the bootloader from Printerboard above.
*
* "Marlin_AT90USB" makes PWM0A available rather than the usual PWM1C. These PWMs share
* the same physical pin. Marlin uses TIMER1 to generate interrupts and sets it up such
* that PWM1A, PWM1B & PWM1C can not be used.
*
* Installation:
*
* 1. In the Arduino IDE, under Files -> Preferences paste the following URL
* https://rawgit.com/Bob-the-Kuhn/Marlin_AT90USB/master/package_MARLIN_AT90USB_index.json
* 2. Under Tools -> Board -> Boards manager, scroll to the bottom, click on MARLIN_AT90USB
* and then click on "Install"
* 3. Select "AT90USB1286_TEENSYPP" from the 'Tools -> Boards' menu.
*/
/**
* To burn the bootloader that comes with Printrboard and Marlin_AT90USB:
*
* 1. Connect your programmer to the board.
* 2. In the Arduino IDE select "Printrboard" or "AT90USB1286_TEENSYPP" and then select the programmer.
* 3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message.
* 4. The programmer is no longer needed. Remove it.
*/
#ifndef __AVR_AT90USB1286__ #ifndef __AVR_AT90USB1286__
#error "Oops! Make sure you have 'Brainwave Pro' selected from the 'Tools -> Boards' menu." #error "Oops! Make sure you have 'Teensy++ 2.0', 'AT90USB1286_TEENSYPP', or 'Printrboard' selected from the 'Tools -> Boards' menu."
#endif #endif
#include "fastio.h" #include "fastio.h"
#if DISABLED(AT90USBxx_TEENSYPP_ASSIGNMENTS) // use Teensyduino Teensy++2.0 pin assignments instead of Marlin alphabetical. #if DISABLED(AT90USBxx_TEENSYPP_ASSIGNMENTS) // use Teensyduino Teensy++2.0 pin assignments instead of Marlin alphabetical.
#error "Uncomment #define AT90USBxx_TEENSYPP_ASSIGNMENTS in fastio.h for this config" #error "Uncomment '#define AT90USBxx_TEENSYPP_ASSIGNMENTS' in fastio.h for this config"
#endif #endif
#define BOARD_NAME "Brainwave Pro" #define BOARD_NAME "Brainwave Pro"

7
Marlin/pins_FELIX2.h
View file

@ -54,3 +54,10 @@
#define SD_DETECT_PIN 6 #define SD_DETECT_PIN 6
#endif // NEWPANEL && ULTRA_LCD #endif // NEWPANEL && ULTRA_LCD
//
// M3/M4/M5 - Spindle/Laser Control
//
#undef SPINDLE_LASER_PWM_PIN // Definitions in pins_RAMPS.h are not valid with this board
#undef SPINDLE_LASER_ENABLE_PIN
#undef SPINDLE_DIR_PIN

26
Marlin/pins_GEN3_MONOLITHIC.h
View file

@ -24,6 +24,31 @@
* Gen3 Monolithic Electronics pin assignments * Gen3 Monolithic Electronics pin assignments
*/ */
/**
* Rev B 26 DEC 2016
*
* added pointer to a current Arduino IDE extension
*
*/
/**
* A useable Arduino IDE extension (board manager) can be found at
* https://github.com/Lauszus/Sanguino
*
* This extension has been tested on Arduino 1.6.12 & 1.8.0
*
* Here's the JSON path:
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
*
* When installing select 1.0.2
*
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
* Just use the above JSON URL instead of Sparkfun's JSON.
*
* Once installed select the Sanguino board and then select the CPU.
*
*/
#ifndef __AVR_ATmega644P__ #ifndef __AVR_ATmega644P__
#error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu." #error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
#endif #endif
@ -73,3 +98,4 @@
#define PS_ON_PIN 14 // Alex, does this work on the card? #define PS_ON_PIN 14 // Alex, does this work on the card?
// Alex extras from Gen3+ // Alex extras from Gen3+

27
Marlin/pins_GEN3_PLUS.h
View file

@ -24,6 +24,32 @@
* Gen3+ pin assignments * Gen3+ pin assignments
*/ */
/**
* Rev B 26 DEC 2016
*
* added pointer to a current Arduino IDE extension
*
*/
/**
* A useable Arduino IDE extension (board manager) can be found at
* https://github.com/Lauszus/Sanguino
*
* This extension has been tested on Arduino 1.6.12 & 1.8.0
*
* Here's the JSON path:
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
*
* When installing select 1.0.2
*
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
* Just use the above JSON URL instead of Sparkfun's JSON.
*
* Once installed select the SANGUINO board and then select the CPU.
*
*/
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__) #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__)
#error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu." #error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
#endif #endif
@ -73,4 +99,3 @@
// //
#define SDSS 4 #define SDSS 4
#define PS_ON_PIN 14 #define PS_ON_PIN 14

35
Marlin/pins_GEN6.h
View file

@ -24,6 +24,33 @@
* Gen6 pin assignments * Gen6 pin assignments
*/ */
/**
* Rev B 26 DEC 2016
*
* 1) added pointer to a current Arduino IDE extension
* 2) added support for M3, M4 & M5 spindle control commands
* 3) added case light pin definition
*
*/
/**
* A useable Arduino IDE extension (board manager) can be found at
* https://github.com/Lauszus/Sanguino
*
* This extension has been tested on Arduino 1.6.12 & 1.8.0
*
* Here's the JSON path:
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
*
* When installing select 1.0.2
*
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
* Just use the above JSON URL instead of Sparkfun's JSON.
*
* Once installed select the Sanguino board and then select the CPU.
*
*/
#ifndef __AVR_ATmega644P__ #ifndef __AVR_ATmega644P__
#ifndef __AVR_ATmega1284P__ #ifndef __AVR_ATmega1284P__
#error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu." #error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
@ -80,7 +107,15 @@
// //
#define SDSS 17 #define SDSS 17
#define DEBUG_PIN 0 #define DEBUG_PIN 0
#define CASE_LIGHT_PIN 16 // MUST BE HARDWARE PWM
// RS485 pins // RS485 pins
#define TX_ENABLE_PIN 12 #define TX_ENABLE_PIN 12
#define RX_ENABLE_PIN 13 #define RX_ENABLE_PIN 13
//
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_ENABLE_PIN 5 // Pin should have a pullup/pulldown!
#define SPINDLE_LASER_PWM_PIN 16 // MUST BE HARDWARE PWM
#define SPINDLE_DIR_PIN 6

26
Marlin/pins_GEN6_DELUXE.h
View file

@ -24,6 +24,32 @@
* Gen6 Deluxe pin assignments * Gen6 Deluxe pin assignments
*/ */
/**
* Rev B 26 DEC 2016
*
* added pointer to a current Arduino IDE extension
*
*/
/**
* A useable Arduino IDE extension (board manager) can be found at
* https://github.com/Lauszus/Sanguino
*
* This extension has been tested on Arduino 1.6.12 & 1.8.0
*
* Here's the JSON path:
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
*
* When installing select 1.0.2
*
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
* Just use the above JSON URL instead of Sparkfun's JSON.
*
* Once installed select the SANGUINO board and then select the CPU.
*
*/
#define BOARD_NAME "Gen6 Deluxe" #define BOARD_NAME "Gen6 Deluxe"
#include "pins_GEN6.h" #include "pins_GEN6.h"

52
Marlin/pins_GEN7_12.h
View file

@ -24,8 +24,35 @@
* Gen7 v1.1, v1.2, v1.3 pin assignments * Gen7 v1.1, v1.2, v1.3 pin assignments
*/ */
/**
* Rev B 26 DEC 2016
*
* 1) added pointer to a current Arduino IDE extension
* 2) added support for M3, M4 & M5 spindle control commands
* 3) added case light pin definition
*
*/
/**
* A useable Arduino IDE extension (board manager) can be found at
* https://github.com/Lauszus/Sanguino
*
* This extension has been tested on Arduino 1.6.12 & 1.8.0
*
* Here's the JSON path:
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
*
* When installing select 1.0.2
*
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
* Just use the above JSON URL instead of Sparkfun's JSON.
*
* Once installed select the Sanguino board and then select the CPU.
*
*/
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__) #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
#error "Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu." #error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
#endif #endif
#ifndef BOARD_NAME #ifndef BOARD_NAME
@ -39,10 +66,13 @@
// //
// Limit Switches // Limit Switches
// //
#define X_STOP_PIN 7 #define X_MIN_PIN 7
#define Y_STOP_PIN 5 #define Y_MIN_PIN 5
#define Z_MIN_PIN 1 #define Z_MIN_PIN 1
#define Z_MAX_PIN 0 #define Z_MAX_PIN 0
#define Y_MAX_PIN 2
#define X_MAX_PIN 6
// //
// Z Probe (when not Z_MIN_PIN) // Z Probe (when not Z_MIN_PIN)
@ -91,6 +121,12 @@
// //
#define PS_ON_PIN 15 #define PS_ON_PIN 15
#if GEN7_VERSION < 13
#define CASE_LIGHT_PIN 16 // MUST BE HARDWARE PWM
#else // Gen7 v1.3 removed the I2C connector & signals so need to get PWM off the PC power supply header
#define CASE_LIGHT_PIN 15 // MUST BE HARDWARE PWM
#endif
// All these generations of Gen7 supply thermistor power // All these generations of Gen7 supply thermistor power
// via PS_ON, so ignore bad thermistor readings // via PS_ON, so ignore bad thermistor readings
#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE #define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE
@ -101,3 +137,13 @@
#define TX_ENABLE_PIN 12 #define TX_ENABLE_PIN 12
#define RX_ENABLE_PIN 13 #define RX_ENABLE_PIN 13
//
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_ENABLE_PIN 10 // Pin should have a pullup/pulldown!
#define SPINDLE_DIR_PIN 11
#if GEN7_VERSION < 13
#define SPINDLE_LASER_PWM_PIN 16 // MUST BE HARDWARE PWM
#else // Gen7 v1.3 removed the I2C connector & signals so need to get PWM off the PC power supply header
#define SPINDLE_LASER_PWM_PIN 15 // MUST BE HARDWARE PWM
#endif

25
Marlin/pins_GEN7_13.h
View file

@ -24,6 +24,31 @@
* Gen7 v1.3 pin assignments * Gen7 v1.3 pin assignments
*/ */
/**
* Rev B 26 DEC 2016
*
* added pointer to a current Arduino IDE extension
*
*/
/**
* A useable Arduino IDE extension (board manager) can be found at
* https://github.com/Lauszus/Sanguino
*
* This extension has been tested on Arduino 1.6.12 & 1.8.0
*
* Here's the JSON path:
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
*
* When installing select 1.0.2
*
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
* Just use the above JSON URL instead of Sparkfun's JSON.
*
* Once installed select the Sanguino board and then select the CPU.
*
*/
#define BOARD_NAME "Gen7 v1.3" #define BOARD_NAME "Gen7 v1.3"
#define GEN7_VERSION 13 // v1.3 #define GEN7_VERSION 13 // v1.3

49
Marlin/pins_GEN7_14.h
View file

@ -24,8 +24,35 @@
* Gen7 v1.4 pin assignments * Gen7 v1.4 pin assignments
*/ */
/**
* Rev B 26 DEC 2016
*
* 1) added pointer to a current Arduino IDE extension
* 2) added support for M3, M4 & M5 spindle control commands
* 3) added case light pin definition
*
*/
/**
* A useable Arduino IDE extension (board manager) can be found at
* https://github.com/Lauszus/Sanguino
*
* This extension has been tested on Arduino 1.6.12 & 1.8.0
*
* Here's the JSON path:
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
*
* When installing select 1.0.2
*
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
* Just use the above JSON URL instead of Sparkfun's JSON.
*
* Once installed select the Sanguino board and then select the CPU.
*
*/
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__) #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
#error "Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu." #error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
#endif #endif
#define BOARD_NAME "Gen7 v1.4" #define BOARD_NAME "Gen7 v1.4"
@ -67,17 +94,25 @@
// //
// Heaters // Heaters
// //
#define HEATER_0_PIN 4 #define HEATER_0_PIN 4
#define HEATER_BED_PIN 3 #define HEATER_BED_PIN 3
// //
// Misc. Functions // Misc. Functions
// //
#define PS_ON_PIN 15 #define PS_ON_PIN 15
#define CASE_LIGHT_PIN 15 // MUST BE HARDWARE PWM
// A pin for debugging // A pin for debugging
#define DEBUG_PIN 0 #define DEBUG_PIN 0
// RS485 pins // RS485 pins
#define TX_ENABLE_PIN 12 #define TX_ENABLE_PIN 12
#define RX_ENABLE_PIN 13 #define RX_ENABLE_PIN 13
//
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_ENABLE_PIN 20 // Pin should have a pullup/pulldown!
#define SPINDLE_LASER_PWM_PIN 16 // MUST BE HARDWARE PWM
#define SPINDLE_DIR_PIN 21

37
Marlin/pins_GEN7_CUSTOM.h
View file

@ -27,8 +27,35 @@
* Please review the pins and adjust them for your needs. * Please review the pins and adjust them for your needs.
*/ */
/**
* Rev B 26 DEC 2016
*
* 1) added pointer to a current Arduino IDE extension
* 2) added support for M3, M4 & M5 spindle control commands
* 3) added case light pin definition
*
*/
/**
* A useable Arduino IDE extension (board manager) can be found at
* https://github.com/Lauszus/Sanguino
*
* This extension has been tested on Arduino 1.6.12 & 1.8.0
*
* Here's the JSON path:
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
*
* When installing select 1.0.2
*
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
* Just use the above JSON URL instead of Sparkfun's JSON.
*
* Once installed select the Sanguino board and then select the CPU.
*
*/
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__) #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
#error "Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu." #error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
#endif #endif
#define BOARD_NAME "Gen7 Custom" #define BOARD_NAME "Gen7 Custom"
@ -76,6 +103,7 @@
// //
#define SDSS 31 // SCL pin of I2C header || CS Pin for SD Card support #define SDSS 31 // SCL pin of I2C header || CS Pin for SD Card support
#define PS_ON_PIN 19 #define PS_ON_PIN 19
#define CASE_LIGHT_PIN 15 // MUST BE HARDWARE PWM
// A pin for debugging // A pin for debugging
#define DEBUG_PIN -1 #define DEBUG_PIN -1
@ -101,3 +129,10 @@
// RS485 pins // RS485 pins
//#define TX_ENABLE_PIN 12 //#define TX_ENABLE_PIN 12
//#define RX_ENABLE_PIN 13 //#define RX_ENABLE_PIN 13
//
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_ENABLE_PIN 5 // Pin should have a pullup/pulldown!
#define SPINDLE_LASER_PWM_PIN 16 // MUST BE HARDWARE PWM
#define SPINDLE_DIR_PIN 6

5
Marlin/pins_K8400.h
View file

@ -66,3 +66,8 @@
#undef PS_ON_PIN #undef PS_ON_PIN
#undef KILL_PIN #undef KILL_PIN
#undef SD_DETECT_PIN #undef SD_DETECT_PIN
#if Z_STEP_PIN == 26
#undef Z_STEP_PIN
#define Z_STEP_PIN 32
#endif

8
Marlin/pins_MEGACONTROLLER.h
View file

@ -127,6 +127,7 @@
// //
#define SDSS 53 #define SDSS 53
#define LED_PIN 13 #define LED_PIN 13
#define CASE_LIGHT_PIN 2
// //
// LCD / Controller // LCD / Controller
@ -152,3 +153,10 @@
#define SD_DETECT_PIN 49 #define SD_DETECT_PIN 49
#endif // MINIPANEL #endif // MINIPANEL
//
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_PWM_PIN 6 // MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 7 // Pin should have a pullup!
#define SPINDLE_DIR_PIN 8

8
Marlin/pins_MEGATRONICS.h
View file

@ -97,6 +97,7 @@
#define SDSS 53 #define SDSS 53
#define LED_PIN 13 #define LED_PIN 13
#define PS_ON_PIN 12 #define PS_ON_PIN 12
#define CASE_LIGHT_PIN 2
// //
// LCD / Controller // LCD / Controller
@ -120,3 +121,10 @@
#define SD_DETECT_PIN -1 // RAMPS doesn't use this #define SD_DETECT_PIN -1 // RAMPS doesn't use this
#endif // ULTRA_LCD && NEWPANEL #endif // ULTRA_LCD && NEWPANEL
//
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_PWM_PIN 3 // MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 4 // Pin should have a pullup!
#define SPINDLE_DIR_PIN 11

12
Marlin/pins_MEGATRONICS_2.h
View file

@ -71,8 +71,8 @@
#define E1_DIR_PIN 39 #define E1_DIR_PIN 39
#define E1_ENABLE_PIN 28 #define E1_ENABLE_PIN 28
#define E2_STEP_PIN 23 #define E2_STEP_PIN 23 // ? schematic says 24
#define E2_DIR_PIN 24 #define E2_DIR_PIN 24 // ? schematic says 23
#define E2_ENABLE_PIN 22 #define E2_ENABLE_PIN 22
// //
@ -112,6 +112,7 @@
#define SDSS 53 #define SDSS 53
#define LED_PIN 13 #define LED_PIN 13
#define PS_ON_PIN 12 #define PS_ON_PIN 12
#define CASE_LIGHT_PIN 2
// //
// LCD / Controller // LCD / Controller
@ -129,3 +130,10 @@
#define BTN_EN1 61 #define BTN_EN1 61
#define BTN_EN2 59 #define BTN_EN2 59
#define BTN_ENC 43 #define BTN_ENC 43
//
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_PWM_PIN 3 // MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 16 // Pin should have a pullup!
#define SPINDLE_DIR_PIN 11

27
Marlin/pins_MEGATRONICS_3.h
View file

@ -28,6 +28,8 @@
#error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu." #error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu."
#endif #endif
#define MEGATRONICS_31
#if ENABLED(MEGATRONICS_31) #if ENABLED(MEGATRONICS_31)
#define BOARD_NAME "Megatronics v3.1" #define BOARD_NAME "Megatronics v3.1"
#else #else
@ -129,6 +131,7 @@
#define SDSS 53 #define SDSS 53
#define LED_PIN 13 #define LED_PIN 13
#define PS_ON_PIN 12 #define PS_ON_PIN 12
#define CASE_LIGHT_PIN 45 // try the keypad connector
// //
// LCD / Controller // LCD / Controller
@ -164,3 +167,27 @@
#endif #endif
#endif #endif
//
// M3/M4/M5 - Spindle/Laser Control
//
#if DISABLED(REPRAPWORLD_KEYPAD) // try to use the keypad connector first
#define SPINDLE_LASER_PWM_PIN 44 // MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 43 // Pin should have a pullup!
#define SPINDLE_DIR_PIN 42
#elif EXTRUDERS <= 2
// try to hijack the last extruder so that we can get the PWM signal off the Y breakout
// move all the Y signals to the E2 extruder socket - makes dual Y steppers harder
#undef Y_ENABLE_PIN
#undef Y_STEP_PIN
#undef Y_DIR_PIN
#undef E2_STEP_PIN
#undef E2_ENABLE_PIN
#undef E2_DIR_PIN
#define Y_ENABLE_PIN 23
#define Y_STEP_PIN 22
#define Y_DIR_PIN 60
#define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 17 // Pin should have a pullup!
#define SPINDLE_DIR_PIN 5
#endif

31
Marlin/pins_MIGHTYBOARD_REVE.h
View file

@ -41,6 +41,17 @@
* *
*/ */
/**
* Rev B 2 JAN 2017
*
* Added pin definitions for:
* M3, M4 & M5 spindle control commands
* case light
*
* Corrected pin assignment for MOSFET_B_PIN pin. Changed it from 9 to 11. The port
* number (B5) agrees with the schematic but B5 is assigned to logical pin 11.
*/
#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__) #if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
#error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu." #error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu."
#endif #endif
@ -140,7 +151,7 @@
// With no heated bed, an additional 24V fan is possible. // With no heated bed, an additional 24V fan is possible.
// //
#define MOSFET_A_PIN 6 // H3 #define MOSFET_A_PIN 6 // H3
#define MOSFET_B_PIN 11 // B5 #define MOSFET_B_PIN 11 // B5 - Rev A of this file had this pin assigned to 9
#define MOSFET_C_PIN 45 // L4 #define MOSFET_C_PIN 45 // L4
#define MOSFET_D_PIN 44 // L5 #define MOSFET_D_PIN 44 // L5
@ -193,11 +204,11 @@
#define LED_PIN 13 // B7 #define LED_PIN 13 // B7
#define CUTOFF_RESET_PIN 16 // H1 #define CUTOFF_RESET_PIN 16 // H1
#define CUTOFF_TEST_PIN 17 // H0 #define CUTOFF_TEST_PIN 17 // H0
#define CASE_LIGHT_PIN 44 // L5 MUST BE HARDWARE PWM
// //
// LCD / Controller // LCD / Controller
// //
#ifdef REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER #ifdef REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
#define LCD_PINS_RS 33 // C4, LCD-STROBE #define LCD_PINS_RS 33 // C4, LCD-STROBE
@ -246,7 +257,6 @@
#endif #endif
// //
// SD Card // SD Card
// //
@ -255,7 +265,20 @@
#define MAX_PIN THERMO_SCK_PIN #define MAX_PIN THERMO_SCK_PIN
//check if all pins are defined in mega/pins_arduino.h //
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_ENABLE_PIN 66 // K4 Pin should have a pullup!
#define SPINDLE_LASER_PWM_PIN 8 // H5 MUST BE HARDWARE PWM
#define SPINDLE_DIR_PIN 67 // K5
// Check if all pins are defined in mega/pins_arduino.h
#include <Arduino.h> #include <Arduino.h>
static_assert(NUM_DIGITAL_PINS > MAX_PIN, "add missing pins to [arduino dir]/hardware/arduino/avr/variants/mega/pins_arduino.h based on fastio.h" static_assert(NUM_DIGITAL_PINS > MAX_PIN, "add missing pins to [arduino dir]/hardware/arduino/avr/variants/mega/pins_arduino.h based on fastio.h"
"to digital_pin_to_port_PGM, digital_pin_to_bit_mask_PGM, digital_pin_to_timer_PGM, NUM_DIGITAL_PINS, see below"); "to digital_pin_to_port_PGM, digital_pin_to_bit_mask_PGM, digital_pin_to_timer_PGM, NUM_DIGITAL_PINS, see below");

10
Marlin/pins_MINIRAMBO.h
View file

@ -111,6 +111,7 @@
// //
#define SDSS 53 #define SDSS 53
#define LED_PIN 13 #define LED_PIN 13
#define CASE_LIGHT_PIN 9
// //
// LCD / Controller // LCD / Controller
@ -140,3 +141,12 @@
#endif // NEWPANEL #endif // NEWPANEL
#endif // ULTRA_LCD #endif // ULTRA_LCD
//
// M3/M4/M5 - Spindle/Laser Control
//
// use P1 connector for spindle pins
#define SPINDLE_LASER_PWM_PIN 9 // MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 18 // Pin should have a pullup!
#define SPINDLE_DIR_PIN 19

23
Marlin/pins_MINITRONICS.h
View file

@ -24,6 +24,13 @@
* Minitronics v1.0/1.1 pin assignments * Minitronics v1.0/1.1 pin assignments
*/ */
/**
* Rev B 2 JAN 2017
*
* Added pin definitions for M3, M4 & M5 spindle control commands
*
*/
#ifndef __AVR_ATmega1281__ #ifndef __AVR_ATmega1281__
#error "Oops! Make sure you have 'Minitronics' selected from the 'Tools -> Boards' menu." #error "Oops! Make sure you have 'Minitronics' selected from the 'Tools -> Boards' menu."
#endif #endif
@ -123,3 +130,19 @@
#define SD_DETECT_PIN -1 // Minitronics doesn't use this #define SD_DETECT_PIN -1 // Minitronics doesn't use this
#endif #endif
//
// M3/M4/M5 - Spindle/Laser Control
//
#if ENABLED(SPINDLE_LASER_ENABLE) // assumes we're only doing CNC work (no 3D printing)
#undef HEATER_BED_PIN
#undef TEMP_BED_PIN // need to free up some pins but also need to
#undef TEMP_0_PIN // re-assign them (to unused pins) because Marlin
#undef TEMP_1_PIN // requires the presence of certain pins or else it
#define HEATER_BED_PIN 4 // won't compile
#define TEMP_BED_PIN 50
#define TEMP_0_PIN 51
#define SPINDLE_LASER_ENABLE_PIN 52 // using A6 because it already has a pull up on it
#define SPINDLE_LASER_PWM_PIN 3 // WARNING - LED & resistor pull up to +12/+24V stepper voltage
#define SPINDLE_DIR_PIN 53
#endif

11
Marlin/pins_MKS_BASE.h
View file

@ -22,6 +22,8 @@
/** /**
* MKS BASE 1.0 – Arduino Mega2560 with RAMPS v1.4 pin assignments * MKS BASE 1.0 – Arduino Mega2560 with RAMPS v1.4 pin assignments
*
* Rev B - Override pin definitions for CASE_LIGHT and M3/M4/M5 spindle control
*/ */
#if HOTENDS > 2 || E_STEPPERS > 2 #if HOTENDS > 2 || E_STEPPERS > 2
@ -36,4 +38,13 @@
// Power outputs EFBF or EFBE // Power outputs EFBF or EFBE
#define MOSFET_D_PIN 7 #define MOSFET_D_PIN 7
#define CASE_LIGHT_PIN 2
//
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_PWM_PIN 2 // MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 15 // Pin should have a pullup!
#define SPINDLE_DIR_PIN 19
#include "pins_RAMPS.h" #include "pins_RAMPS.h"

25
Marlin/pins_OMCA.h
View file

@ -51,6 +51,31 @@
* REF http://sanguino.cc/hardware * REF http://sanguino.cc/hardware
*/ */
/**
* Rev B 26 DEC 2016
*
* added pointer to a current Arduino IDE extension
*
*/
/**
* A useable Arduino IDE extension (board manager) can be found at
* https://github.com/Lauszus/Sanguino
*
* This extension has been tested on Arduino 1.6.12 & 1.8.0
*
* Here's the JSON path:
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
*
* When installing select 1.0.2
*
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
* Just use the above JSON URL instead of Sparkfun's JSON.
*
* Once installed select the Sanguino board and then select the CPU.
*
*/
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__)
#error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. (Final OMCA board)" #error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. (Final OMCA board)"
#endif #endif

27
Marlin/pins_OMCA_A.h
View file

@ -50,8 +50,33 @@
* *
*/ */
/**
* Rev B 26 DEC 2016
*
* added pointer to a current Arduino IDE extension
*
*/
/**
* A useable Arduino IDE extension (board manager) can be found at
* https://github.com/Lauszus/Sanguino
*
* This extension has been tested on Arduino 1.6.12 & 1.8.0
*
* Here's the JSON path:
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
*
* When installing select 1.0.2
*
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
* Just use the above JSON URL instead of Sparkfun's JSON.
*
* Once installed select the Sanguino board and then select the CPU.
*
*/
#ifndef __AVR_ATmega644__ #ifndef __AVR_ATmega644__
#error "Oops! Make sure you have 'SanguinoA' selected from the 'Tools -> Boards' menu." #error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
#endif #endif
#define BOARD_NAME "Alpha OMCA" #define BOARD_NAME "Alpha OMCA"

8
Marlin/pins_RAMBO.h
View file

@ -137,6 +137,7 @@
#define LED_PIN 13 #define LED_PIN 13
#define FILWIDTH_PIN 3 // Analog Input #define FILWIDTH_PIN 3 // Analog Input
#define PS_ON_PIN 4 #define PS_ON_PIN 4
#define CASE_LIGHT_PIN 46
// //
// LCD / Controller // LCD / Controller
@ -208,3 +209,10 @@
#endif // !NEWPANEL #endif // !NEWPANEL
#endif // ULTRA_LCD #endif // ULTRA_LCD
//
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_PWM_PIN 45 // MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 31 // Pin should have a pullup!
#define SPINDLE_DIR_PIN 32

26
Marlin/pins_RAMPS.h
View file

@ -204,6 +204,16 @@
#define PS_ON_PIN 12 #define PS_ON_PIN 12
#if !PIN_EXISTS(CASE_LIGHT) && !defined(SPINDLE_LASER_ENABLE_PIN)
#undef CASE_LIGHT_PIN
#if !defined(NUM_SERVOS) || NUM_SERVOS == 0 // try to use servo connector first
#define CASE_LIGHT_PIN 6 // MUST BE HARDWARE PWM
#elif !(ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL) \
&& (ENABLED(PANEL_ONE) || ENABLED(VIKI2) || ENABLED(miniVIKI) || ENABLED(MINIPANEL) || ENABLED(REPRAPWORLD_KEYPAD))) // try to use AUX 2
#define CASE_LIGHT_PIN 44 // MUST BE HARDWARE PWM
#endif
#endif
// //
// LCD / Controller // LCD / Controller
// //
@ -361,3 +371,19 @@
#endif // NEWPANEL #endif // NEWPANEL
#endif // ULTRA_LCD #endif // ULTRA_LCD
//
// M3/M4/M5 - Spindle/Laser Control
//
#if ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENABLE_PIN)
#if !defined(NUM_SERVOS) || NUM_SERVOS == 0 // try to use servo connector first
#define SPINDLE_LASER_ENABLE_PIN 4 // Pin should have a pullup/pulldown!
#define SPINDLE_LASER_PWM_PIN 6 // MUST BE HARDWARE PWM
#define SPINDLE_DIR_PIN 5
#elif !(ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL) \
&& (ENABLED(PANEL_ONE) || ENABLED(VIKI2) || ENABLED(miniVIKI) || ENABLED(MINIPANEL) || ENABLED(REPRAPWORLD_KEYPAD))) // try to use AUX 2
#define SPINDLE_LASER_ENABLE_PIN 40 // Pin should have a pullup/pulldown!
#define SPINDLE_LASER_PWM_PIN 44 // MUST BE HARDWARE PWM
#define SPINDLE_DIR_PIN 65
#endif
#endif

8
Marlin/pins_RAMPS_OLD.h
View file

@ -101,3 +101,11 @@
#define SDPOWER 48 #define SDPOWER 48
#define SDSS 53 #define SDSS 53
#define LED_PIN 13 #define LED_PIN 13
#define CASE_LIGHT_PIN 45 // MUST BE HARDWARE PWM
//
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_ENABLE_PIN 41 // Pin should have a pullup/pulldown!
#define SPINDLE_LASER_PWM_PIN 45 // MUST BE HARDWARE PWM
#define SPINDLE_DIR_PIN 43

18
Marlin/pins_RIGIDBOARD.h
View file

@ -82,16 +82,16 @@
// //
// Heaters / Fans // Heaters / Fans
// //
#undef HEATER_BED_PIN #undef HEATER_BED_PIN
#define HEATER_BED_PIN 10 #define HEATER_BED_PIN 10
#undef FAN_PIN #undef FAN_PIN
#define FAN_PIN 8 // Same as RAMPS_13_EEF #define FAN_PIN 8 // Same as RAMPS_13_EEF
// //
// Misc. Functions // Misc. Functions
// //
#undef PS_ON_PIN #undef PS_ON_PIN
#define PS_ON_PIN -1 #define PS_ON_PIN -1
// //
@ -110,24 +110,24 @@
#define BTN_RT 32 #define BTN_RT 32
// 'R' button // 'R' button
#undef BTN_ENC #undef BTN_ENC
#define BTN_ENC 31 #define BTN_ENC 31
// Disable encoder // Disable encoder
#undef BTN_EN1 #undef BTN_EN1
#define BTN_EN1 -1 #define BTN_EN1 -1
#undef BTN_EN2 #undef BTN_EN2
#define BTN_EN2 -1 #define BTN_EN2 -1
#undef SD_DETECT_PIN #undef SD_DETECT_PIN
#define SD_DETECT_PIN 22 #define SD_DETECT_PIN 22
#elif ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) #elif ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
#undef SD_DETECT_PIN #undef SD_DETECT_PIN
#define SD_DETECT_PIN 22 #define SD_DETECT_PIN 22
#undef KILL_PIN #undef KILL_PIN
#define KILL_PIN 32 #define KILL_PIN 32
#endif #endif

12
Marlin/pins_RUMBA.h
View file

@ -100,7 +100,7 @@
#endif #endif
#if TEMP_SENSOR_2 == -1 #if TEMP_SENSOR_2 == -1
#define TEMP_2_PIN 7 // Analog Input (connector *K3* on RUMBA thermocouple ADD ON is used <-- this can't be used when TEMP_SENSOR_BED is defined as thermocouple) #define TEMP_2_PIN 7 // Analog Input (connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_BED is defined as thermocouple)
#else #else
#define TEMP_2_PIN 13 // Analog Input (default connector for thermistor *T2* on rumba board is used) #define TEMP_2_PIN 13 // Analog Input (default connector for thermistor *T2* on rumba board is used)
#endif #endif
@ -109,7 +109,7 @@
//#define TEMP_X_PIN 12 // Analog Input (default connector for thermistor *T3* on rumba board is used) //#define TEMP_X_PIN 12 // Analog Input (default connector for thermistor *T3* on rumba board is used)
#if TEMP_SENSOR_BED == -1 #if TEMP_SENSOR_BED == -1
#define TEMP_BED_PIN 7 // Analog Input (connector *K3* on RUMBA thermocouple ADD ON is used <-- this can't be used when TEMP_SENSOR_2 is defined as thermocouple) #define TEMP_BED_PIN 7 // Analog Input (connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_2 is defined as thermocouple)
#else #else
#define TEMP_BED_PIN 11 // Analog Input (default connector for thermistor *THB* on rumba board is used) #define TEMP_BED_PIN 11 // Analog Input (default connector for thermistor *THB* on rumba board is used)
#endif #endif
@ -133,6 +133,7 @@
#define LED_PIN 13 #define LED_PIN 13
#define PS_ON_PIN 45 #define PS_ON_PIN 45
#define KILL_PIN 46 #define KILL_PIN 46
#define CASE_LIGHT_PIN 45
// //
// LCD / Controller // LCD / Controller
@ -148,3 +149,10 @@
#define BTN_EN1 11 #define BTN_EN1 11
#define BTN_EN2 12 #define BTN_EN2 12
#define BTN_ENC 43 #define BTN_ENC 43
//
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 14 // Pin should have a pullup!
#define SPINDLE_DIR_PIN 15

98
Marlin/pins_SANGUINOLOLU_11.h
View file

@ -24,6 +24,33 @@
* Sanguinololu board pin assignments * Sanguinololu board pin assignments
*/ */
/**
* Rev B 26 DEC 2016
*
* 1) added pointer to a current Arduino IDE extension
* 2) added support for M3, M4 & M5 spindle control commands
* 3) added case light pin definition
*
*/
/**
* A useable Arduino IDE extension (board manager) can be found at
* https://github.com/Lauszus/Sanguino
*
* This extension has been tested on Arduino 1.6.12 & 1.8.0
*
* Here's the JSON path:
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
*
* When installing select 1.0.2
*
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
* Just use the above JSON URL instead of Sparkfun's JSON.
*
* Once installed select the Sanguino board and then select the CPU.
*
*/
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__) #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__)
#error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu." #error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
#endif #endif
@ -96,19 +123,26 @@
// //
// Misc. Functions // Misc. Functions
// //
/** /**
* On some broken versions of the Sanguino libraries the pin definitions are wrong, * In some versions of the Sanguino libraries the pin
* which then needs SDSS as pin 24. But you should upgrade your Sanguino libraries! See #368. * definitions are wrong, with SDSS = 24 and LED_PIN = 28 (Melzi).
* If you encounter issues with these pins, upgrade your
* Sanguino libraries! See #368.
*/ */
//#define SDSS 24 //#define SDSS 24
#define SDSS 31 #define SDSS 31
#if IS_MELZI #if IS_MELZI
#define LED_PIN 27 // On some broken versions of the Sanguino libraries the pin definitions are wrong, so LED_PIN needs to be 28. But you should upgrade your Sanguino libraries! See #368. #define LED_PIN 27
#elif MB(STB_11) #elif MB(STB_11)
#define LCD_BACKLIGHT_PIN 17 // LCD backlight LED #define LCD_BACKLIGHT_PIN 17 // LCD backlight LED
#endif #endif
#if DISABLED(SPINDLE_LASER_ENABLE) && ENABLED(SANGUINOLOLU_V_1_2) && !(ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)) // try to use IO Header
#define CASE_LIGHT_PIN 4 // MUST BE HARDWARE PWM - see if IO Header is available
#endif
// //
// LCD / Controller // LCD / Controller
// //
@ -181,14 +215,62 @@
#else #else
#define BTN_ENC 30 #define BTN_ENC 30
#endif #endif
#elif ENABLED(OLED_PANEL_TINYBOY2) #else // !Panelolu2
#define BTN_ENC 28
#define LCD_SDSS -1
#else // !Panelolu2, !TinyBoy2
#define BTN_ENC 16 #define BTN_ENC 16
#define LCD_SDSS 28 // Smart Controller SD card reader rather than the Melzi #define LCD_SDSS 28 // Smart Controller SD card reader rather than the Melzi
#endif // !Panelolu2, !TinyBoy2 #endif // !Panelolu2
#define SD_DETECT_PIN -1 #define SD_DETECT_PIN -1
#endif // ULTRA_LCD && NEWPANEL #endif // ULTRA_LCD && NEWPANEL
//
// M3/M4/M5 - Spindle/Laser Control
//
#if ENABLED(SPINDLE_LASER_ENABLE)
#if !MB(AZTEEG_X1) && ENABLED(SANGUINOLOLU_V_1_2) && !(ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)) // try to use IO Header
#define SPINDLE_LASER_ENABLE_PIN 10 // Pin should have a pullup/pulldown!
#define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM
#define SPINDLE_DIR_PIN 11
#elif !MB(MELZI) // use X stepper motor socket
/**
* To control the spindle speed and have an LCD you must sacrifice
* the Extruder and pull some signals off the X stepper driver socket.
*
* The following assumes:
* - The X stepper driver socket is empty
* - The extruder driver socket has a driver board plugged into it
* - The X stepper wires are attached the the extruder connector
*/
/**
* Where to get the spindle signals
*
* spindle signal socket name socket name
* -------
* /ENABLE O| |O VMOT
* MS1 O| |O GND
* MS2 O| |O 2B
* MS3 O| |O 2A
* /RESET O| |O 1A
* /SLEEP O| |O 1B
* SPINDLE_LASER_PWM_PIN STEP O| |O VDD
* SPINDLE_LASER_ENABLE_PIN DIR O| |O GND
* -------
*
* Note: Socket names vary from vendor to vendor.
*/
#undef X_DIR_PIN
#undef X_ENABLE_PIN
#undef X_STEP_PIN
#define X_DIR_PIN 0
#define X_ENABLE_PIN 14
#define X_STEP_PIN 1
#define SPINDLE_LASER_PWM_PIN 15 // MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 21 // Pin should have a pullup!
#define SPINDLE_DIR_PIN -1 // No pin available on the socket for the direction pin
#endif
#endif // SPINDLE_LASER_ENABLE

16
Marlin/pins_SAV_MKI.h
View file

@ -115,7 +115,6 @@
#define EXT_AUX_A4 4 // Analog #define EXT_AUX_A4 4 // Analog
#define EXT_AUX_A4_IO 44 // Digital IO, 42 (teensy), 44 (marlin) #define EXT_AUX_A4_IO 44 // Digital IO, 42 (teensy), 44 (marlin)
// //
// LCD / Controller // LCD / Controller
// //
@ -134,10 +133,23 @@
#endif // SAV_3DLCD #endif // SAV_3DLCD
#if ENABLED(SAV_3DLCD) || ENABLED(SAV_3DGLCD) #if ENABLED(SAV_3DLCD) || ENABLED(SAV_3DGLCD)
#define BTN_EN1 EXT_AUX_A1_IO #define BTN_EN1 EXT_AUX_A1_IO
#define BTN_EN2 EXT_AUX_A0_IO #define BTN_EN2 EXT_AUX_A0_IO
#define BTN_ENC EXT_AUX_PWM_D24 #define BTN_ENC EXT_AUX_PWM_D24
#define KILL_PIN EXT_AUX_A2_IO #define KILL_PIN EXT_AUX_A2_IO
#define HOME_PIN EXT_AUX_A4_IO #define HOME_PIN EXT_AUX_A4_IO
#endif // SAV_3DLCD || SAV_3DGLCD
#else // Try to use the expansion header for spindle control
//
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_PWM_PIN 24 // 12 AT90USB… pin #
#define SPINDLE_LASER_ENABLE_PIN 39 // Pin should have a pullup! 41 AT90USB… pin #
#define SPINDLE_DIR_PIN 40 // 42 AT90USB… pin #
#define CASE_LIGHT_PIN 0 // 24 AT90USB… pin #
#endif

25
Marlin/pins_SETHI.h
View file

@ -24,6 +24,31 @@
* Sethi 3D_1 pin assignments - www.sethi3d.com.br * Sethi 3D_1 pin assignments - www.sethi3d.com.br
*/ */
/**
* Rev B 26 DEC 2016
*
* added pointer to a current Arduino IDE extension
* this assumes that this board uses the Sanguino pin map
*/
/**
* A useable Arduino IDE extension (board manager) can be found at
* https://github.com/Lauszus/Sanguino
*
* This extension has been tested on Arduino 1.6.12 & 1.8.0
*
* Here's the JSON path:
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
*
* When installing select 1.0.2
*
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
* Just use the above JSON URL instead of Sparkfun's JSON.
*
* Once installed select the Sanguino board and then select the CPU.
*
*/
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__) #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
#error "Oops! Make sure you have 'Sethi 3D' selected from the 'Tools -> Boards' menu." #error "Oops! Make sure you have 'Sethi 3D' selected from the 'Tools -> Boards' menu."
#endif #endif

8
Marlin/pins_TEENSY2.h
View file

@ -124,6 +124,7 @@
#define SDSS 20 // 8 #define SDSS 20 // 8
#define LED_PIN 6 #define LED_PIN 6
#define PS_ON_PIN 27 #define PS_ON_PIN 27
#define CASE_LIGHT_PIN 1 // MUST BE HARDWARE PWM
// //
// LCD / Controller // LCD / Controller
@ -139,3 +140,10 @@
#define BTN_EN2 39 #define BTN_EN2 39
#define BTN_ENC 40 #define BTN_ENC 40
#endif #endif
//
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_ENABLE_PIN 5 // Pin should have a pullup!
#define SPINDLE_LASER_PWM_PIN 0 // MUST BE HARDWARE PWM
#define SPINDLE_DIR_PIN 7

161
Marlin/pins_TEENSYLU.h
View file

@ -12,27 +12,82 @@
* *
* This program is distributed in the hope that it will be useful, * This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of * but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details. * GNU General Public License for more details.
* *
* You should have received a copy of the GNU General Public License * You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>. * along with this program. If not, see <http://www.gnu.org/licenses/>.
* *
*/ */
/** /**
* Teensylu 0.7 pin assignments (AT90USB1286) * rev B 30 DEC 2016
* Requires the Teensyduino software with Teensy++ 2.0 selected in Arduino IDE! *
* http://www.pjrc.com/teensy/teensyduino.html * The original version of this file did NOT result in a useful program because:
* See http://reprap.org/wiki/Printrboard for more info * 1. The pin numbers assumed that the "#define AT90USBxx_TEENSYPP_ASSIGNMENTS" line
* in FASTIO.h was commented out. There wasn't an Arduino IDE 1.6.x extension/package
* that supported this pin map so the latest Marlin wouldn't compile.
* 2. The silkscreen for the four end stops don't agree with the schematic. Activating
* the X endstop would tell the software that the Y endstop just went active.
* 3. The thermistor inputs also had heater names assigned to them. The result was
* thermistor inputs that were set to digital outputs.
*
* Rev B corrects the above problems by:
* 1. The "Marlin_AT90USB" extension/package was developed. This extension enables the
* latest Marlin software to compile using Arduino IDE 1.6.x and 1.80.
* 2. The endstop pin numbers in this file were changed to match the silkscreen. This
* makes it a little confusing when trying to correlate the schematic with the pin
* numbers used in this file.
* 3. The offending heater names were deleted.
*
* To create a useable image for Teensylu do the following:
* a) Install the Marlin_AT90USB extension with either of the following methods:
* Automatic - paste this URL into preferences and then use Boards manager
* https://rawgit.com/Bob-the-Kuhn/Marlin_AT90USB/master/package_MARLIN_AT90USB_index.json
* Manual:
* 1. Copy the following URL into Go to "https://github.com/Bob-the-Kuhn/Marlin_AT90USB",
* click on the "Clone or Download" button and then click on "Download ZIP" button.
* 2. Unzip the file, find the "Marlin_AT90USB" directory and then copy it to the
* hardware directory in Arduino. The Arduino hardware directory will probably be
* located in a path similar to this: C:\Program Files (x86)\Arduino\hardware
* b) Connect the USBtinyISP to the board.
* c) In the Arduino IDE select the "AT90USB1286_STANDARD" board in the of the "Marlin_AT90USB"
* section and select the "USBtinyISP" programmer.
* d) In the Arduino IDE click on "burn bootloader". Don't worry about the "verify
* failed at 1F000" error message.
* e) The USBtinyISP programmer is no longer needed. Remove it.
* f) In FASTIO.h comment out the "#define AT90USBxx_TEENSYPP_ASSIGNMENTS" line.
* g) To upload a sketch do the following:
* 1. remove the jumper
* 2. press reset
* 3. click on the "upload" button in the Arduino IDE
* 4. wait until the upload finishes (less than a minute)
* 5. put the jumper back on
* 6. press the reset button
*
*
* NOTE - the "Marlin_AT90USB" pin maps make PWM0A available rather than the usual PWM1C.
* These PWMs share the same physical pin. Marlin uses TIMER1 to generate
* interrupts and sets it up such that PWM1A, PWM1B & PWM1C can not be used.
*/ */
#ifndef __AVR_AT90USB1286__ /**
#error "Oops! Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu." * SILKSCREEN ERROR
*
* The silkscreen for the endstops do NOT match the schematic. The silkscreen SHOULD
* read (from left to right) X-STOP, Y-STOP, Z-STOP & E-STOP. The silkscreen actually
* reads E-STOP, X-STOP, Y-STOP & Z-STOP.
*
* The pin assignments in this file match the silkscreen.
*/
#if !defined(__AVR_AT90USB1286__) && !defined(__AVR_AT90USB1286P__)
#error "Oops! Make sure you have 'AT90USB1286_STANDARD' selected from the 'Tools -> Boards' menu."
#endif #endif
#if ENABLED(AT90USBxx_TEENSYPP_ASSIGNMENTS) // use Teensyduino Teensy++2.0 pin assignments instead of Marlin traditional. #if ENABLED(AT90USBxx_TEENSYPP_ASSIGNMENTS)
#error "These Teensylu assignments depend on traditional Marlin assignments, not AT90USBxx_TEENSYPP_ASSIGNMENTS in fastio.h" #error "please disable (comment out) the AT90USBxx_TEENSYPP_ASSIGNMENTS flag in FASTIO.h "
#endif #endif
#define BOARD_NAME "Teensylu" #define BOARD_NAME "Teensylu"
@ -40,74 +95,84 @@
#define USBCON 1286 // Disable MarlinSerial etc. #define USBCON 1286 // Disable MarlinSerial etc.
#define LARGE_FLASH true #define LARGE_FLASH true
// //
// Limit Switches // Limit Switche definitions that match the SCHEMATIC
// //
#define X_STOP_PIN 13 //#define X_STOP_PIN 13
#define Y_STOP_PIN 14 //#define Y_STOP_PIN 14
#define Z_STOP_PIN 15 //#define Z_STOP_PIN 15
//#define E_STOP_PIN 36
//
// Limit Switch definitions that match the SILKSCREEN
//
#define X_STOP_PIN 14
#define Y_STOP_PIN 15
#define Z_STOP_PIN 36
//#define E_STOP_PIN 13
// //
// Steppers // Steppers
// //
#define X_STEP_PIN 0 #define X_STEP_PIN 0
#define X_DIR_PIN 1 #define X_DIR_PIN 1
#define X_ENABLE_PIN 39 #define X_ENABLE_PIN 39
#define Y_STEP_PIN 2 #define Y_STEP_PIN 2
#define Y_DIR_PIN 3 #define Y_DIR_PIN 3
#define Y_ENABLE_PIN 38 #define Y_ENABLE_PIN 38
#define Z_STEP_PIN 4 #define Z_STEP_PIN 4
#define Z_DIR_PIN 5 #define Z_DIR_PIN 5
#define Z_ENABLE_PIN 23 #define Z_ENABLE_PIN 23
#define E0_STEP_PIN 6
#define E0_DIR_PIN 7
#define E0_ENABLE_PIN 19
#define E0_STEP_PIN 6
#define E0_DIR_PIN 7
#define E0_ENABLE_PIN 19
//
// Temperature Sensors // Temperature Sensors
//
#define TEMP_0_PIN 7 // Analog Input (Extruder) #define TEMP_0_PIN 7 // Analog Input (Extruder)
#define TEMP_BED_PIN 6 // Analog Input (Bed) #define TEMP_BED_PIN 6 // Analog Input (Bed)
// //
// Heaters / Fans // Heaters / Fans
// //
#define HEATER_0_PIN 21 // Extruder #define HEATER_0_PIN 21 // Extruder
#define HEATER_1_PIN 46 #define HEATER_BED_PIN 20
#define HEATER_2_PIN 47
#define HEATER_BED_PIN 20
// If soft or fast PWM is off then use Teensyduino pin numbering, Marlin #define FAN_PIN 22
// fastio pin numbering otherwise
#if ENABLED(FAN_SOFT_PWM) || ENABLED(FAST_PWM_FAN)
#define FAN_PIN 22
#else
#define FAN_PIN 16
#endif
// //
// Misc. Functions // Misc. Functions
// //
#define SDSS 8 #define SDSS 8
#define CASE_LIGHT_PIN 24
// //
// LCD / Controller // LCD / Controller
// //
#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL) #if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
#define BEEPER_PIN -1 #define BEEPER_PIN -1
#if ENABLED(LCD_I2C_PANELOLU2) #if ENABLED(LCD_I2C_PANELOLU2)
#define BTN_EN1 27 // RX1 - fastio.h pin mapping 27 #define BTN_EN1 27
#define BTN_EN2 26 // TX1 - fastio.h pin mapping 26 #define BTN_EN2 26
#define BTN_ENC 43 // A3 - fastio.h pin mapping 43 #define BTN_ENC 43
#define SDSS 40 // use SD card on Panelolu2 (Teensyduino pin mapping) #define SDSS 40 // use SD card on Panelolu2
#endif // LCD_I2C_PANELOLU2 #endif // LCD_I2C_PANELOLU2
#define SD_DETECT_PIN -1 #define SD_DETECT_PIN -1
#endif // ULTRA_LCD && NEWPANEL #endif // ULTRA_LCD && NEWPANEL
//
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_PWM_PIN 12 // MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 41 // Pin should have a pullup!
#define SPINDLE_DIR_PIN 42

21
Marlin/pins_ULTIMAIN_2.h
View file

@ -24,6 +24,14 @@
* Ultiboard v2.0 pin assignments * Ultiboard v2.0 pin assignments
*/ */
/**
* Rev B 2 JAN 2017
*
* Added pin definitions for:
* M3, M4 & M5 spindle control commands
* case light
*/
#ifndef __AVR_ATmega2560__ #ifndef __AVR_ATmega2560__
#error "Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu." #error "Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu."
#endif #endif
@ -110,3 +118,16 @@
#define BTN_EN1 40 #define BTN_EN1 40
#define BTN_EN2 41 #define BTN_EN2 41
#define BTN_ENC 19 #define BTN_ENC 19
//
// M3/M4/M5 - Spindle/Laser Control
//
#if ENABLED(SPINDLE_LASER_ENABLE) // use the LED_PIN for spindle speed control or case light
#undef LED_PIN
#define SPINDLE_DIR_PIN 16
#define SPINDLE_LASER_ENABLE_PIN 17 // Pin should have a pullup!
#define SPINDLE_LASER_PWM_PIN 8 // MUST BE HARDWARE PWM
#else
#undef LED_PIN
#define CASE_LIGHT_PIN 8
#endif

16
Marlin/pins_ULTIMAKER.h
View file

@ -24,6 +24,14 @@
* Ultimaker pin assignments * Ultimaker pin assignments
*/ */
/**
* Rev B 2 JAN 2017
*
* Added pin definitions for:
* M3, M4 & M5 spindle control commands
* case light
*/
#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__) #if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
#error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu." #error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu."
#endif #endif
@ -102,6 +110,7 @@
#define LED_PIN 13 #define LED_PIN 13
#define PS_ON_PIN 12 #define PS_ON_PIN 12
#define SUICIDE_PIN 54 // PIN that has to be turned on right after start, to keep power flowing. #define SUICIDE_PIN 54 // PIN that has to be turned on right after start, to keep power flowing.
#define CASE_LIGHT_PIN 8
// //
// LCD / Controller // LCD / Controller
@ -146,3 +155,10 @@
#endif // !NEWPANEL #endif // !NEWPANEL
#endif // ULTRA_LCD #endif // ULTRA_LCD
//
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_PWM_PIN 9 // MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 10 // Pin should have a pullup!
#define SPINDLE_DIR_PIN 11 // use the EXP3 PWM header

220
Marlin/pins_ULTIMAKER_OLD.h
View file

@ -24,6 +24,42 @@
* Ultimaker pin assignments (Old electronics) * Ultimaker pin assignments (Old electronics)
*/ */
/**
* Rev B 3 JAN 2017
*
* Details on pin definitions for M3, M4 & M5 spindle control commands and for
* the CASE_LIGHT_PIN are at the end of this file.
*
* This started out as an attempt to add pin definitions for M3, M4 & M5 spindle
* control commands but quickly turned into a head scratcher as the sources for
* the revisions provided inconsistent information.
*
* As best I can determine:
* 1.5.3 boards should use the pins_ULTIMAKER.h file which means the BOARD_NAME
* define in this file should say 1.5.3 rather than 1.5.4
* This file is meant for 1.1 - 1.3 boards.
* The endstops for the 1.0 boards use different definitions than on the 1.1 - 1.3
* boards.
*
* I've added sections that have the 1.0 and 1.5.3 + endstop definitions so you can
* easily switch if needed. I've also copied over the 1.5.3 + LCD definitions.
*
* To be 100% sure of the board you have:
* 1. In Configuration_adv.h enable "PINS_DEBUGGING"
* 2. Compile & uploade
* 3. Enter the command "M43 W1 I1". This command will report that pin nmumber and
* name of any pin that changes state.
* 4. Using a 1k (approximately) resistor pull the endstops and some of the LCD pins
* to ground and see what is reported.
* 5. If the reported pin doesn't match the file then try a different board revision
* and repeat steps 2 - 5
*/
#define board_rev_1_1_TO_1_3
//#define board_rev_1_0
//#define board_rev_1_5
#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__) #if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
#error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu." #error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu."
#endif #endif
@ -37,18 +73,38 @@
// //
// Limit Switches // Limit Switches
// //
#define X_MIN_PIN 15 #if ENABLED(board_rev_1_1_TO_1_3)
#define X_MAX_PIN 14 #define X_MIN_PIN 15 // SW1
#define Y_MIN_PIN 17 #define X_MAX_PIN 14 // SW2
#define Y_MAX_PIN 16 #define Y_MIN_PIN 17 // SW3
#define Z_MIN_PIN 19 #define Y_MAX_PIN 16 // SW4
#define Z_MAX_PIN 18 #define Z_MIN_PIN 19 // SW5
#define Z_MAX_PIN 18 // SW6
#endif
#if ENABLED(board_rev_1_0)
#define X_MIN_PIN 13 // SW1
#define X_MAX_PIN 12 // SW2
#define Y_MIN_PIN 11 // SW3
#define Y_MAX_PIN 10 // SW4
#define Z_MIN_PIN 9 // SW5
#define Z_MAX_PIN 8 // SW6
#endif
#if ENABLED(board_rev_1_5)
#define X_MIN_PIN 22
#define X_MAX_PIN 24
#define Y_MIN_PIN 26
#define Y_MAX_PIN 28
#define Z_MIN_PIN 30
#define Z_MAX_PIN 32
#endif
// //
// Z Probe (when not Z_MIN_PIN) // Z Probe (when not Z_MIN_PIN)
// //
#ifndef Z_MIN_PROBE_PIN #ifndef Z_MIN_PROBE_PIN
#define Z_MIN_PROBE_PIN 18 #define Z_MIN_PROBE_PIN Z_MAX_PIN
#endif #endif
// //
@ -70,9 +126,9 @@
#define E0_DIR_PIN 45 #define E0_DIR_PIN 45
#define E0_ENABLE_PIN 41 #define E0_ENABLE_PIN 41
#define E1_STEP_PIN -1 #define E1_STEP_PIN -1 // 49
#define E1_DIR_PIN -1 #define E1_DIR_PIN -1 // 47
#define E1_ENABLE_PIN -1 #define E1_ENABLE_PIN -1 // 48
// //
// Temperature Sensors // Temperature Sensors
@ -84,14 +140,144 @@
// Heaters / Fans // Heaters / Fans
// //
#define HEATER_0_PIN 2 #define HEATER_0_PIN 2
#define HEATER_1_PIN 1 //#define HEATER_1_PIN 3 // used for case light Rev A said "1"
#define HEATER_BED_PIN 4
// //
// LCD / Controller // LCD / Controller
// //
#define LCD_PINS_RS 24 #if ENABLED(board_rev_1_0) || ENABLED(board_rev_1_1_TO_1_3)
#define LCD_PINS_ENABLE 22 #define LCD_PINS_RS 24
#define LCD_PINS_D4 36 #define LCD_PINS_ENABLE 22
#define LCD_PINS_D5 34 #define LCD_PINS_D4 36
#define LCD_PINS_D6 32 #define LCD_PINS_D5 34
#define LCD_PINS_D7 30 #define LCD_PINS_D6 32
#define LCD_PINS_D7 30
#elif ENABLED(board_rev_1_5) && ENABLED(ULTRA_LCD)
#define BEEPER_PIN 18
#if ENABLED(NEWPANEL)
#define LCD_PINS_RS 20
#define LCD_PINS_ENABLE 17
#define LCD_PINS_D4 16
#define LCD_PINS_D5 21
#define LCD_PINS_D6 5
#define LCD_PINS_D7 6
// buttons are directly attached
#define BTN_EN1 40
#define BTN_EN2 42
#define BTN_ENC 19
#define SD_DETECT_PIN 38
#else // !NEWPANEL - Old style panel with shift register
// buttons are attached to a shift register
#define SHIFT_CLK 38
#define SHIFT_LD 42
#define SHIFT_OUT 40
#define SHIFT_EN 17
#define LCD_PINS_RS 16
#define LCD_PINS_ENABLE 5
#define LCD_PINS_D4 6
#define LCD_PINS_D5 21
#define LCD_PINS_D6 20
#define LCD_PINS_D7 19
#define SD_DETECT_PIN -1
#endif // !NEWPANEL
#endif // ULTRA_LCD
//
// case light - see spindle section for more info on available hardware PWMs
//
#if !PIN_EXISTS(CASE_LIGHT) && ENABLED(board_rev_1_5)
#define CASE_LIGHT_PIN 7 // use PWM - MUST BE HARDWARE PWM
#endif
//
// M3/M4/M5 - Spindle/Laser Control
//
#if ENABLED(SPINDLE_LASER_ENABLE)
#if ENABLED(board_rev_1_0) // use the last three SW positions
#undef Z_MIN_PROBE_PIN
#undef X_MIN_PIN // SW1
#undef X_MAX_PIN // SW2
#undef Y_MIN_PIN // SW3
#undef Y_MAX_PIN // SW4
#undef Z_MIN_PIN // SW5
#undef Z_MAX_PIN // SW6
#define X_STOP_PIN 13 // SW1 (didn't change) - also has a useable hardware PWM
#define Y_STOP_PIN 12 // SW2
#define Z_STOP_PIN 11 // SW3
#define SPINDLE_DIR_PIN 10 // SW4
#define SPINDLE_LASER_PWM_PIN 9 // SW5 MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 8 // SW6 Pin should have a pullup!
#elif ENABLED(board_rev_1_5) // use the same pins - but now they are on a different connector
#define SPINDLE_DIR_PIN 10 // EXP3-6 (silkscreen says 10)
#define SPINDLE_LASER_PWM_PIN 9 // EXP3-7 (silkscreen says 9) MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 8 // EXP3-8 (silkscreen says 8) Pin should have a pullup!
#elif ENABLED(board_rev_1_1_TO_1_3)
/**
* Only four hardware PWMs physically connected to anything on these boards:
*
* HEATER_0_PIN 2 silkscreen varies - usually "PWM 1" or "HEATER1"
* HEATER_1_PIN 3 silkscreen varies - usually "PWM 2" or "HEATER2"
* HEATER_BED_PIN 4 silkscreen varies - usually "PWM 3" or "HEATED BED"
* E0_DIR_PIN 45
*
* If one of the heaters is used then special precautions will usually be needed.
* They have an LED and resistor pullup to +24V which could damage 3.3V-5V ICs.
*/
#if EXTRUDERS == 1 // Move E0 stepper module to the spare and get signals from E0
#undef E0_STEP_PIN
#undef E0_DIR_PIN
#undef E0_ENABLE_PIN
#define E0_STEP_PIN 49
#define E0_DIR_PIN 47
#define E0_ENABLE_PIN 48
#define SPINDLE_DIR_PIN 43
#define SPINDLE_LASER_PWM_PIN 45 // MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 41 // Pin should have a pullup!
#elif TEMP_SENSOR_BED == 0 // Can't use E0 so see if HEATER_BED_PIN is available
#undef HEATER_BED_PIN
#define SPINDLE_DIR_PIN 38 // Probably pin 4 on 10 pin connector closest to the E0 socket
#define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM - Special precautions usually needed.
#define SPINDLE_LASER_ENABLE_PIN 40 // Pin should have a pullup! (Probably pin 6 on the 10-pin
// connector closest to the E0 socket)
#endif
#endif
#endif
/**
* Where to get the spindle signals on the E0 socket
*
* spindle signal socket name socket name
* -------
* SPINDLE_LASER_ENABLE_PIN /ENABLE *| |O VMOT
* MS1 O| |O GND
* MS2 O| |O 2B
* MS3 O| |O 2A
* /RESET O| |O 1A
* /SLEEP O| |O 1B
* SPINDLE_DIR_PIN STEP O| |O VDD
* SPINDLE_LASER_PWM_PIN DIR O| |O GND
* -------
* * - pin closest to MS1, MS2 & MS3 jumpers on the board
*
* Note: Socket names vary from vendor to vendor.
*/