Scott Lahteine
be691b51f1
Remove references to marlinfirmware.org
...
The domain is gone and doesn’t redirect, so for now show no URL on the boot screen.
2016-02-17 14:41:46 -08:00
Scott Lahteine
f3f58bd619
Merge pull request #2992 from thinkyhead/rc_rename_fpos_t
...
Rename fpos_t to avoid libc conflict
2016-02-17 14:40:33 -08:00
Scott Lahteine
b03787262a
Merge pull request #2868 from esenapaj/esenapaj-patch-1
...
Fix AUTOTEMP documentation in configs
2016-02-17 14:15:29 -08:00
Scott Lahteine
83ffc9eb4f
Show raw steps in M114
...
This is a proposed change. This section of M114 output is a debug
extension according to RepRap wiki.
2016-02-15 15:59:24 -08:00
Scott Lahteine
373e8a1ad4
Fixes for COREXY and COREXZ coordinates
2016-02-15 15:59:24 -08:00
unknown
31656e68bc
Fix for homing X and Y before raising Z when Z_SAFE_HOMING is set.
2016-02-15 15:53:40 -06:00
unknown
8ea55323d8
Fix for not raising Z before homing X and Y
2016-02-15 14:52:04 -06:00
Scott Lahteine
b83e472bd3
Rename fpos_t to avoid libc conflict
2016-02-10 20:49:25 -08:00
Scott Lahteine
68457ee903
For Dual Y/Z use the next available extruder pins
2016-02-09 21:59:09 -08:00
Scott Lahteine
711e5db19a
Tweak comment in process_next_command
2016-02-09 18:16:35 -08:00
Scott Lahteine
400e9329be
Allow spaces after a code letter
2016-02-09 18:03:13 -08:00
Scott Lahteine
cdcb80f3c5
Allow no-space after initial command
...
Addresses issue #2715
2016-02-09 18:00:35 -08:00
AnHardt
6f473f7fc6
Repair N in ADVANCED_OK
...
Send the correct line number.
If no N was in the command - non't send an N.
2016-02-09 19:23:26 +01:00
AnHardt
efbd705eda
Replace the "ok" in M280, M301, M304, M851 with output not including an "ok"
...
Replace the "ok" in M280, M301, M304, M851 with output not including an "ok"
to avoid senting two "ok"s for a single g-code.
Doing the same for M105 would break the input filters of the hosts.
For M105 the other "ok" is omitted.
2016-02-09 13:36:03 +01:00
Scott Lahteine
8e66028d25
Apply the ABL rotation matrix to the extruder offset.
2016-02-08 14:22:18 -08:00
esenapaj
ab5aa3fc92
Merge pull request #5 from MarlinFirmware/RCBugFix
...
Rc bug fix
2016-02-08 05:42:11 +09:00
esenapaj
27d918d836
Merge pull request #4 from MarlinFirmware/RCBugFix
...
Rc bug fix
2016-02-08 05:35:32 +09:00
Scott Lahteine
159ff94afd
Remove obsolete HEATER_BED_DUTY_CYCLE_DIVIDER #2977
2016-02-07 08:02:11 -06:00
Richard Wackerbarth
1112dcd3c2
Merge Slow SD Handling #2848
2016-02-07 08:00:14 -06:00
Ruwan J Egoda Gamage
1270fbfd38
Using SET_INPUT instead of pinMode
2016-02-07 07:58:52 -06:00
Ruwan J Egoda Gamage
b58083b0fa
Getting rid of SDEXTRASLOW, SDSLOW variables.
2016-02-07 07:58:52 -06:00
Ruwan J Egoda Gamage
1833049b8a
reusing millis()
2016-02-07 07:58:52 -06:00
Ruwan J Egoda Gamage
1b7c443628
Adding SDULTRASLOW variable.
...
Instead of changing SDEXTRASLOW variable to a slower speed, the new
SDULTRASLOW is used for rigidbot panel.
2016-02-07 07:58:52 -06:00
Ruwan J Egoda Gamage
6f9e9c0e4f
Cleaning up, getting rid of the fake encoder count variable.
2016-02-07 07:58:52 -06:00
Ruwan J Egoda Gamage
becbfe1065
Fixing Rigidbot LCD Panel Support
2016-02-07 07:58:52 -06:00
esenapaj
4882a7eded
more suitable display format for delta printer
2016-01-29 18:38:25 +09:00
esenapaj
d7272e3f36
Merge pull request #3 from MarlinFirmware/RCBugFix
...
Rc bug fix
2016-01-29 05:43:22 +09:00
esenapaj
9ed1275a37
Merge pull request #1 from MarlinFirmware/RCBugFix
...
Rc bug fix
2016-01-29 05:40:33 +09:00
Scott Lahteine
62bad1b60f
Merge pull request #2848 from japzi/RCBugFix
...
Fixing Rigidbot LCD Panel Support
2016-01-26 17:30:12 -08:00
esenapaj
59d345a3dd
Update Configuration.h
2016-01-22 07:27:11 -06:00
esenapaj
b8f0c8a4c7
Update Configuration.h
2016-01-22 07:27:11 -06:00
esenapaj
df0d599c79
Update Configuration.h
2016-01-22 07:27:11 -06:00
esenapaj
a366697649
Update Configuration.h
2016-01-22 07:27:11 -06:00
Richard Wackerbarth
7c94c83765
Repair formula mangled by PR#1319 in Jan 2015
2016-01-15 10:06:27 -06:00
Richard Wackerbarth
51aa7d93eb
Merge pull request #2902 from Naruto-kyun/patch-1
...
Update stepper.cpp
2016-01-15 10:04:15 -06:00
Naruto-kyun
2932602643
Update stepper.cpp
...
Forgot Z2_MIN_PIN
2016-01-15 16:50:43 +01:00
Ruwan J Egoda Gamage
06555febdd
Using SET_INPUT instead of pinMode
2015-12-24 12:12:25 -05:00
esenapaj
8d2aa2368d
Update Configuration_adv.h
2015-12-23 08:16:36 +09:00
esenapaj
0de5fcad0a
Update Configuration_adv.h
2015-12-23 08:16:06 +09:00
esenapaj
1403b9acc0
Update Configuration_adv.h
2015-12-23 08:15:20 +09:00
esenapaj
5cf1c38ea1
Update Configuration_adv.h
2015-12-23 08:12:54 +09:00
esenapaj
04ab61bf40
Update Configuration_adv.h
2015-12-23 08:12:28 +09:00
esenapaj
39c62fbd6f
Update Configuration_adv.h
2015-12-23 08:12:04 +09:00
esenapaj
efcb769003
Update Configuration_adv.h
2015-12-23 08:09:57 +09:00
esenapaj
992fbb831d
Update Configuration_adv.h
2015-12-23 08:08:45 +09:00
esenapaj
5ee6fe6385
Update Configuration_adv.h
2015-12-23 08:07:12 +09:00
esenapaj
056daf00fc
Update Configuration_adv.h
2015-12-23 08:06:15 +09:00
esenapaj
71aafb79a0
Update Configuration_adv.h
2015-12-23 08:03:54 +09:00
Ruwan J Egoda Gamage
2c9e0415c7
Getting rid of SDEXTRASLOW, SDSLOW variables.
2015-12-13 23:23:01 -05:00
Ruwan J Egoda Gamage
a64bcd53e9
reusing millis()
2015-12-13 22:06:03 -05:00
