Johann Rocholl
2292441f0c
Use X/Y/Z_MAX_PIN instead of X/Y/Z_MIN_PIN for top endstops on deltabot.
2012-12-10 00:43:14 -08:00
Johann Rocholl
33247733e0
Teensylu and Printrboard use different analog pins for thermistors.
2012-12-09 02:19:13 -08:00
Johann Rocholl
6cba11f087
Stop redefining MOTHERBOARD and #define AT90USB instead. Also put #ifndef AT90USB around the HardwareSerial_h trick, so now Printrboard / Brainwave support compiles on Arduino 1.0.2 as well.
2012-12-09 01:32:09 -08:00
Johann Rocholl
4d351b4846
Improved formatting and comments for consistency.
2012-12-08 20:15:53 -08:00
Johann Rocholl
a30007caa4
If fastio.h is not messed up then Teensylu and Printrboard are actually using the same pins.
2012-12-08 19:46:42 -08:00
Johann Rocholl
b1c38d4c82
Avoid compiler warnings (redefined MOTHERBOARD) in Arduino 1.0 and greater.
2012-12-08 11:34:18 -08:00
Johann Rocholl
42e21bb06e
Add support for Printrboard (from https://github.com/lincomatic/Marlin ) and Brainwave (from https://github.com/metrix/Sprinter ).
2012-12-08 10:49:01 -08:00
brupje
57429cb9fe
Fix for keypad
2012-11-29 21:42:19 +01:00
Erik vd Zalm
f934d0ef5b
Merge remote-tracking branch 'tonokip/Marlin_v1' into Marlin_v1
...
Conflicts:
Marlin/Configuration.h
2012-11-21 20:36:30 +01:00
daid303
ffc69537aa
Update on some comments, make the MOTHERBOARD list complete again.
2012-11-09 09:10:51 +01:00
Jonathan Bastien-Filiatrault
0f73afb0b0
Avoid defining overriding definitions for the RepRapDiscount Smart
...
Controller. Remove common definitions. Harmonize declaration order.
2012-11-07 16:04:28 -05:00
Jonathan Bastien-Filiatrault
36b452c7ac
Remove abbrs.
2012-11-07 15:42:18 -05:00
Jonathan Bastien-Filiatrault
3cbaad9288
RepRapDiscount Smart Controller pin definitions.
2012-11-06 20:32:13 -05:00
Bracken Dawson
f5631a89e8
Add dummy Emergancy Pin to Gen7 1.4
...
Change required after pulling from ErikZalm.
2012-10-26 22:28:37 +01:00
Bracken Dawson
a4f9e1ebf2
Merge git://github.com/ErikZalm/Marlin into Marlin_v1
2012-10-26 22:20:35 +01:00
Bracken Dawson
2873d67b17
Put bogus temp override back in Gen7 up to 1.3
...
Took out the ifdef when I split 1.4 out and forgot to permanently
define it for <=1.3.
2012-10-26 22:17:26 +01:00
brupje
d07b6e93d5
Add support for Megatronics
2012-10-14 14:05:12 +03:00
johnnyr
8016f058bc
fix max endstop pins
2012-09-19 13:15:17 -05:00
Erik vd Zalm
abf0693e8e
Added KILL_PIN -1 to gen7 boards
2012-09-04 08:20:27 +02:00
Drakelive
d728e35658
Update Marlin/pins.h
2012-08-30 23:36:49 +03:00
tonokip
1c1fddc7ac
Added support for the Rambo reprap electronics board. Added Mcodes to set
...
motor current and microstepping pins.
2012-08-30 00:16:57 -07:00
Bracken Dawson
47d4f55bc0
Fix Gen7 1.4 pinout
...
Gen7 1.4 uses very different pin assignments, might as well make a new
section and remove some of the conditionals from each. It's easier to change
your pin assingment this way if like me you don't wire it exactly to plan.
2012-08-22 23:15:46 +01:00
Enchiridion
50cde90324
Added support for dual Z axis stepper drivers
2012-08-04 00:32:26 -06:00
Chris Palmer
538189cc19
Fixed soft limits when the origin is in the middle.
...
HOME_POS is now always where the endstop is and can be outside the limits.
The limits are now defined by MIN_POS and MAX_POS rather than HOME_POS and MAX_LENGTH.
The Z is axis now homed first if direction is away from the bed.
Saguinololu limit pins change from MIN to MAX according to the homing direction.
2012-07-14 22:24:26 +02:00
Daid
e9bec9b6fe
Fixed E1_ENABLE pin for Ultimaker. This was wrong for the 1.5.4 and 1.5.3 PCB (I cannot check the 1.5.6)
2012-05-24 18:36:55 +02:00
Guan Yang
602c8ee02b
Melzi support
2012-05-09 18:37:07 -04:00
Bernhard
464b755918
added support for the UltiController
2012-04-22 20:55:56 +02:00
Michel Pollet
5550e893d5
New board variant, Open Motion Controller
...
Open Hardware board currently used by the group build of http://tvrrug.org.uk
The board can be found at http://solderpad.com/folknology/open-motion-controller/
Signed-off-by: Michel Pollet <buserror@gmail.com>
2012-03-22 13:51:21 +00:00
Erik van der Zalm
2e749d60c3
Added DISABLE_MAX_ENDSTOPS
2012-03-12 20:32:14 +01:00
ErikZalm
19a47dae4a
Merge pull request #99 from Justblair/master
...
Better pin configuration for rotary encoder in RAMPS boards
2012-03-11 04:34:59 -07:00
Erik van der Zalm
c077316b2b
Added PID autotune. (experimental)
...
M303 Starts autotune. Wait till the Kp Ki and Kd constants are printed.
Put these values in Configuration.h
2012-03-08 21:43:21 +01:00
Blair Thompson
02ee9e3d30
Changed Pin Assignment for the RAMPS motherboard so that LCD and Rotary encoder are all wired to AUX-4
...
This simplifies wiring for those with RAMPS 1.3 and 1.4 boards.
2012-03-04 21:34:20 +00:00
Erik van der Zalm
cb0c84e075
Merge remote-tracking branch 'justblair/master' into Marlin_v1
2012-03-03 20:20:55 +01:00
ErikZalm
1d5809d458
Merge pull request #88 from daid/Marlin_v1
...
Made plan_buffer_line arguments const...
2012-03-03 11:18:14 -08:00
Erik van der Zalm
ed951b1977
Fixed RAMPS 1.2 support (Found and fixed by rrhb)
2012-03-03 20:15:41 +01:00
Blair Thompson
f278e1c00f
This is in my opinion a much better way of dealing with SD cards than my previous fix.
...
Instead of adding a momentary switch to fake the insertion of the card I have modified the ultralcd menu item:
Card Menu -> Refresh
to reinitialise the card providing that the SDCARDDETECT pin has been set to -1 in the pins.h file. This requires one less switch on the front panel and the refresh menu item is in the most relevent place for a user who wishes to inert a card and then print from it.
It also means that the "Card inserted" messages do not bother the users of these card readers (they dont make sense for users without SCCARDDETECT)
2012-03-03 16:30:31 +00:00
Daid
00d33e6b82
Typo fix
2012-02-29 19:01:21 +01:00
Daid
7d124478fa
Only protect the heater pins for the defined extruders.
...
Changed the way the extruder pins are defined so it doesn't create extra -1 entries in the list.
2012-02-29 15:49:02 +01:00
ErikZalm
1ebe7d1ab6
Merge pull request #83 from phord/tempfix
...
Add explicit #define for bogus temp override
2012-02-27 08:36:45 -08:00
Phil Hord
b65ef8d66c
Add support for upcoming Gen7 v1.4
...
V1.4 moves thermistor power to the always-on 5v line.
The BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE is no longer
needed on this board. Add a new motherboard type to
support this feature.
2012-02-26 20:39:49 -05:00
Phil Hord
740f0c7690
Add explicit #define for bogus temp override
...
The code to ignore the "bad thermistor reading failsafe"
suicide function depends on the existing of the PS_ON pin
feature. But in some boards this shouldn't be the case
Fix this by adding an explicit definition to make our
intentions more clear and separable.
2012-02-26 20:26:16 -05:00
Phil Hord
ba8500a236
pins.h: Define Z_MAX_PIN for Gen7 board
...
The Z_MAX_PIN value was defined as no-value, but this causes
the compile to fail. Fix this by setting the Z_MAX_PIN to the
correct value (which happens to be 0 for pin PB0/DIO0/0).
2012-02-26 20:18:39 -05:00
Changwoo Ryu
7b14953c99
Fix build on Sanguino based boards with ATmega1284P
2012-02-27 04:12:55 +09:00
Daid
286d5003fa
Fixed compiler warning for Sanguino compile
2012-02-26 17:35:01 +01:00
Erik van der Zalm
ce714fe306
Fixes in pins.h
2012-02-25 22:55:17 +01:00
Erik van der Zalm
35e57bf149
Added gen6 deluxe.
2012-02-25 17:44:45 +01:00
Erik van der Zalm
84ea2d61e8
Moved gen7 boards to motherboard type 10, 11 and 12.
...
Split ramps1.3 in Sprinter like config and multiextruder config.
2012-02-24 23:34:41 +01:00
Erik van der Zalm
d298dd121f
merged SBUBA82 and Justblair
2012-02-21 20:26:59 +01:00
Blair Thompson
a05a261b72
Added a workaround. Ramps SD card does not have sdcarddetect. My temporary solution is to add a momentary swtich
...
that pulls down the SDCARDDETECT pin and mimicking the pull and reinsert ofa a SD card
2012-02-18 23:56:31 +00:00
Blair Thompson
1b6765ed12
Updated the pin config for RAMPS 1.3 to include ultimaker new style LCD/Rotary Encoder interface
2012-02-18 18:25:04 +00:00
