Kevin O'Connor
3d91bd486c
Add "kick fan" feature - briefly run fan at full speed on start.
...
Add a feature to run the cooling fan at full speed for a small period
(default 100ms) when first starting the fan. Some fans wont reliably
start spinning at low power, and many fans have issue with the PWM at
low power. However, once the fan starts spinning it can reliably be
set to a wide range of PWM values.
2013-01-08 18:50:15 -05:00
daid
27843388c6
Merge pull request #360 from njprossi/Marlin_v1
...
Power signal control definitions for other power supplies
2013-01-08 02:58:02 -08:00
daid303
921273baa0
Added optional feature to stop printing when an endstop is hit. Made the Z display on the LCD in 3.2 format instead of 3.1. Added LCD message when and endstop is hit.
2013-01-08 11:53:18 +01:00
Nicolas Rossi
f3c1fc70a9
Power signal control definitions for ATX and others
2013-01-07 14:33:30 +01:00
Johann Rocholl
1f45cb0a51
Fix typo in MANUAL_HOME_POSITION (plural S missing) and improve comments.
2012-12-11 01:54:40 -08:00
daid303
587154c01b
Fix the WATCHPERIOD implementation. It did not work correctly in a multi extruder setup, it did not work after 32 seconds after startup (int16 used as millies timestamp). And it did not work if you gave an M104 or M109 when the target was already around the target setpoint. So on average, it did not work at all. The new implementation should be robust in detecting a failure to heat up.
2012-12-06 10:36:07 +01:00
Erik vd Zalm
f934d0ef5b
Merge remote-tracking branch 'tonokip/Marlin_v1' into Marlin_v1
...
Conflicts:
Marlin/Configuration.h
2012-11-21 20:36:30 +01:00
daid303
f6ff0ab767
signed/unsigned fixes.
2012-11-06 15:33:49 +01:00
daid303
b6ff45254e
Better explain the watchdog "problem" and rename the config define so it explains that the feature belongs to the watchdog.
2012-11-06 13:33:00 +01:00
daid303
7e348fcb5f
By mistake enabled the watchdog by default. This should be off by default.
2012-11-06 13:20:08 +01:00
daid303
06b58a9c4f
First cleanup. Moved all code to cpp files, so there are no dependencies on pde files. And no more odd requirement to cat files together. (Still need to fix the Makefile). Also cleaned up some defines and made defines upper case as by C coding conventions.
2012-11-06 12:06:41 +01:00
ErikZalm
36a746d7d5
Merge pull request #244 from markfinn/pidbed
...
PID for heated bed
2012-10-08 11:15:16 -07:00
Mark Finn
04631d2250
cleanup for pull
2012-09-17 14:17:24 -05:00
ZetaPhoenix
c6caa45ae2
Limit Switch locations based on MIN/MAX limits and homing direction
...
fixes #246
Added statements to set the limit switch positions to the maximum travel if homing in the positive direction as well as bed center at (0,0) if defined.
Relocated code based on feedback.
2012-09-15 15:25:49 -07:00
tonokip
1c1fddc7ac
Added support for the Rambo reprap electronics board. Added Mcodes to set
...
motor current and microstepping pins.
2012-08-30 00:16:57 -07:00
Enchiridion
50cde90324
Added support for dual Z axis stepper drivers
2012-08-04 00:32:26 -06:00
daid
12de8fff81
Support step motor controllers with active low step pins.
2012-06-29 16:27:47 +02:00
Bernhard
0c123950e9
__ header file replace
2012-06-02 20:44:17 +02:00
Bernhard
bf077125b9
added firmware retract. disabled by default
2012-06-02 20:32:28 +02:00
Erik van der Zalm
67cf105bc6
Fixed AUTOTEMP (M109 S215 B260 F1 starts autotemp)
...
Changed SLOWDOWN. IF this does not work ok OLD_SLOWDOWN is the old algo.
2012-04-15 19:17:33 +02:00
Erik van der Zalm
4ca2f336f0
Changed default MINIMUM_PLANNER_SPEED -> 0.05
...
Fixed small bug in arcs
M105 prints now actual_temp/target_temp
2012-04-01 16:23:40 +02:00
Bernhard
1532200435
found error in filenames.
...
One array was too short. This had nothing to do with long filenames, other than if they were 12 characters exactly, which could only happen if the extension and the text before were filled completely
2012-03-19 20:06:58 +01:00
Erik van der Zalm
87ff2f8867
Added CONTROLLERFAN. (Controlling a fan to cool down the steppper drivers)
2012-03-11 10:44:10 +01:00
Erik van der Zalm
c6f2ec3c82
remove stop_heating_wait
2012-02-27 18:45:45 +01:00
Erik van der Zalm
018c567abf
Moved SLOWDOWN function. (jetty840)
...
Included AD595 calibration options. (daid)
2012-02-26 16:23:47 +01:00
Blair Thompson
d9f2f509d5
Added new menu items under the prepare submenu.
...
Instead of a single pre-heat, now there is pre-heat ABS and PLA options
Added defines to the configuration file to adjust preheat temperatures for both
2012-02-22 22:51:04 +00:00
Erik van der Zalm
8816ef1c64
Small fixes after merge
2012-02-21 20:36:43 +01:00
Erik van der Zalm
13e185d330
removed unused HEATING_EARLY_FINISH_DEG_OFFSET
...
Simplified stepper inactive time
2012-02-11 23:22:16 +01:00
Erik van der Zalm
5113513cb2
RC 1
2012-02-08 18:28:54 +01:00
Erik van der Zalm
d8a0c6450f
Split the configuration file in two parts.
...
One for common settings.
One for advanced settings.
2012-02-07 20:23:43 +01:00
