Scott Lahteine
acacee80a2
Add JUNCTION_ACCELERATION_FACTOR to configs
...
Part of #10688
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
2018-05-11 23:13:27 -05:00
Scott Lahteine
4d4bf7897d
Junction Deviation jerk limiting option
2018-05-08 10:08:54 -05:00
Scott Lahteine
840ff60952
Bring some configs up to date
2018-05-06 02:42:27 -05:00
nightdemonx
e911635fb1
Add thermocouple with AD8495 support
2018-05-02 08:43:16 -05:00
Scott Lahteine
05c33833e7
[2.0.x] Add NO_LCD_MENUS option ( #10582 )
2018-04-30 21:16:31 -05:00
Scott Lahteine
11ab017dd0
Creality3D Power-Loss Recovery
2018-04-21 21:56:50 -05:00
Marcio Teixeira
5cc7916e69
Add G29_RETRY_AND_RECOVER feature
...
- Add an option to retry G29, optionally executing a G-code procedure after each failed probe.
2018-04-19 19:45:53 -05:00
Sean
2d9b0a66fe
Add Filament Change accelerations
2018-04-09 23:57:27 -05:00
Lenbok
0e8242180d
Chamber temperature monitoring and auto fan control.
...
This is an initial cut for feedback, updated for 2.0.x.
Chamber temperature is currently reported along with hot end and bed
temperatures to serial. The format is just like that used for hot end
and bed temperatures, but using 'C' prefix. As there is no heater,
target is always 0. Is this appropriate, is there a better way to report
chamber temperatures?
Chamber temperatures are not reported on the LCD in any way.
When auto chamber fan is enabled, it currently just uses the same
temperature threshold as the other auto controlled fans.
As the chamber temperature is not connected to any heater, it doesn't
undergo mintemp/maxtemp monitoring. This would need to change in the
future if chamber heating became a feature.
2018-04-06 23:09:06 -05:00
Sean
2fa0a73c2c
Implement filament change continuous purge
2018-04-04 20:57:51 -05:00
Scott Lahteine
1d22609473
MIN_PROBE_EDGE replaces DELTA_PROBEABLE_RADIUS
2018-03-19 04:11:46 -05:00
Marcio Teixeira
c24dbcbfe1
When STATUS_EXPIRE_SECONDS is 0, hide the position. ( #10081 )
...
Some users may prefer to hide the position updates on the `LIGHTWEIGHT_UI` altogether. This leads to an even less cluttered display (it also saves on SPI traffic and one byte of RAM).
2018-03-14 02:44:30 -05:00
Studiodyne
e7a61de8af
[2.0] FWRetract Reset (Best way) ( #10083 )
2018-03-14 01:35:30 -05:00
Scott Lahteine
e7570f3195
Improve TMC config organization, naming
2018-03-14 00:18:41 -05:00
Bob-the-Kuhn
6b4a928145
2uS default step pulse ( #9989 )
2018-03-07 21:11:01 -06:00
Scott Lahteine
94f5204629
Move AUTO_REPORT_SD_STATUS to SDSUPPORT block
2018-03-07 01:50:30 -06:00
Scott Lahteine
b198b49d15
Followup to AUTO_REPORT_SD_STATUS
...
Followup to #9832
2018-03-07 00:13:42 -06:00
Studiodyne
23a576faf7
[2.0] Fix for FW retract ( #9878 )
2018-03-01 15:15:40 -06:00
Scott Lahteine
b8485528b2
Prettify LCD_PROGRESS_BAR options
2018-02-23 19:19:57 -06:00
Scott Lahteine
e65a853c59
Fix LCD_PROGRESS_BAR
...
Fix #9208
2018-02-23 14:05:10 -06:00
Scott Lahteine
2bd252b501
[2.0.x] LIN_ADVANCE v1.5 ( #9712 )
2018-02-23 00:53:29 -06:00
Marcio Teixeira
532bb3aaa1
Lightweight status screen for ST7920
...
- This status screen uses the ST7920 character generator to greatly
reduce SPI traffic and MCU load when updating the status screen.
- Has been tested with the RepRapDiscount Full Graphics Smart Controller
but should work with any LCD that uses an ST7920 or fully compatible
controller.
2018-02-22 00:10:43 -06:00
Scott Lahteine
59c98d6fd5
Hephestos2 heated bed kit for all ( #9757 )
2018-02-21 22:27:09 -06:00
Kevin
9019ea0fce
Option to force X or Y to home first when homing the other axis
2018-02-18 01:11:41 -06:00
blye
330437ad7c
Update LCD_SET_PROGRESS_MANUALLY in configs
2018-02-17 08:12:10 -06:00
Bob-the-Kuhn
349dafa728
config update (set to -1)
2018-02-15 21:42:54 -06:00
Scott Lahteine
5b70d3da1c
Update DIGIPOT_I2C_MOTOR_CURRENTS comments
2018-02-13 22:54:12 -06:00
Scott Lahteine
694d2ebec0
TMC SW SPI pins in Configuration_adv.h
...
Counterpart to #9632
2018-02-08 18:49:38 -06:00
Thomas Moore
1541224a81
Enable Z axis and delta sensorless homing ( #9516 )
2018-02-08 04:20:44 -06:00
Scott Lahteine
b2f8b4ada5
I2C position encoders update ( #9533 )
...
Updating I2C position encoders to enable babystepping and Babystep XY when using the ecm microstep correction method. Also changed default method to ECM microstep.
2018-02-08 03:57:11 -06:00
Manuel Valentino
374f2a5e16
[2.0.x] Fixed wrong information about TMC2208 wiring ( #9335 )
2018-02-02 04:45:55 -06:00
teemuatlut
5c69d45f5b
[2.0.x] TMC2130 support for LPC platform ( #9114 )
2018-02-01 21:49:40 -06:00
Scott Lahteine
8190fdb260
[2.0.x] Option to use Neopixel as case light ( #9270 )
...
* Add option to use Neopixel as case light
* Apply CASE_LIGHT_USE_NEOPIXEL to example configs
2018-01-20 16:58:41 -06:00
Scott Lahteine
02ff12d491
More up front option to show SD percentage
2018-01-14 23:32:39 -06:00
Scott Lahteine
5c076a6d93
Improved M915 description
2018-01-09 18:56:27 -06:00
teemuatlut
cdc61ebf53
Add M915 configuration option
2018-01-09 18:28:48 +02:00
Scott Lahteine
7541316bb4
Add M701/M702 Filament Load/Unload, M603
2018-01-04 15:07:37 -06:00
Scott Lahteine
2929c9e56f
A specific option to SLIM_LCD_MENUS
2017-12-31 00:11:22 -06:00
Scott Lahteine
f704f405af
Add pause/resume actions on M600, M125
2017-12-25 01:39:18 -06:00
Thomas Moore
f0a8a1a853
[2.0.x] Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE ( #8866 )
...
* Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE
2017-12-25 01:38:06 -06:00
Scott Lahteine
fdc5e72720
A single setting to validate filament width
2017-12-19 21:33:25 -06:00
Scott Lahteine
933f76fda3
Option to disable all volumetric extrusion
2017-12-19 19:51:25 -06:00
robpower
5595098063
V2 Extended NanoDLP_Z_Move_Sync to G4 & G28,Added all axis option.
2017-12-15 16:22:55 -06:00
teemuatlut
0cd1e91056
[2.0.x] TMC driver update ( #8769 )
2017-12-15 15:03:14 -06:00
Scott Lahteine
ae663a4198
PROBE_DOUBLE_TOUCH => MULTIPLE_PROBING
2017-12-07 16:44:13 -06:00
Scott Lahteine
8f90642eea
LED_CONTROL_MENU config changes
2017-11-29 21:02:56 -06:00
Tannoo
cf0f78336b
New Feature: LED_CONTROL_MENU
2017-11-29 21:02:55 -06:00
Scott Lahteine
a67cf78c6b
Clean up whitespace, spacing
2017-11-26 20:18:52 -06:00
Scott Lahteine
7be4857ab9
Tweak BLOCK_BUFFER_SIZE description
2017-11-26 17:36:40 -06:00
Scott Lahteine
5926c9c97b
Followup for MESH_EDIT_GFX_OVERLAY
2017-11-24 15:53:25 -06:00
