jmz52
813a4ea107
Add support for Mks Robin TFT display ( #12706 )
...
* Add support for MKS Robin TFT display
- Add support for MKS Robin TFT display and encoder for MKS Robin board.
- Generic 128x64 UI with x2 upscale is used (for now).
- Tested on MKS Robin TFT V2.0 with ST7789V controller.
2019-01-03 10:38:39 -06:00
jmz52
c4237b529f
Fix MKS Mini and SD card conflct over SPI mode ( #12783 )
2019-01-03 10:27:53 -06:00
Phr3d13
01f75591c6
Fix GTM32_PRO_VB Serial and HAL via watchdog ( #12753 )
...
Move `watchdog_reset` from `.h` to `.cpp` to eliminate the need to include `MarlinConfig.h` in a HAL-related file.
2019-01-03 09:46:49 -06:00
Scott Lahteine
288340cb6c
Followup to VORON
2019-01-03 09:14:14 -06:00
Scott Lahteine
2aaa681dea
Remove unused Cheaptronic pins
2019-01-03 08:58:55 -06:00
Marcio Teixeira
81e753064a
Fix ExtUI compile warnings and error ( #12799 )
2019-01-03 08:36:43 -06:00
Ludy
74c47803f7
Add VORON printer ( #12705 )
2019-01-03 06:27:03 -06:00
kAdonis
637fb20c75
Allow 4 fan animation frames ( #12772 )
2019-01-03 06:03:06 -06:00
petieken
d9cf5e4883
Update pins_BIQU_SKR_V1.1.h ( #12758 )
2019-01-02 13:50:05 -06:00
TheLongAndOnly
cb643d87df
Adding missing code for triple Z-stepper auto-align ( #12786 )
2019-01-01 18:22:04 -06:00
Ludy
14a7faf087
Fix compile warning comparison uint and int ( #12788 )
2019-01-01 18:20:12 -06:00
Marcio Teixeira
60cb36bef3
Misc. improvements ( #12747 )
...
* Make ExtUI respect MAXTEMP limits
- Temperatures are now clamped by MAXTEMP limits rather than arbitrary values.
* Speed up USB init, add status
- Speed up USB initialization
- Show status message if init failed
* Enable status messages for EXTENSIBLE_UI
* Adjust max limit to MAX_TEMP - 15
* Misc. tweaks to formatting, const, etc.
2019-01-01 15:17:48 -06:00
InsanityAutomation
4f2473053c
Fix M106 with SINGLENOZZLE
2018-12-31 20:10:18 -06:00
Reece Kibble
7557f8d68c
Rename all Stm32f1 to STM32F1 ( #12639 )
2018-12-31 16:36:49 -06:00
Scott Lahteine
371d9a1acf
Fix line-endings, formatting, whitespace
...
Followup to #12770
2018-12-30 15:38:20 -06:00
Ludy
135c74017c
Fix compile DEBUG_EEPROM_READWRITE error ( #12746 )
2018-12-30 11:37:20 -06:00
Giuliano Zaro
54ba44ee37
Fix bad sanitycheck ( #12748 )
2018-12-30 10:44:15 -06:00
swilkens
b01a630bd0
[2.0.x] Correct Ender 3 bed size ( #12769 )
2018-12-30 10:42:47 -06:00
Alain Martel
44ed34475b
Add MKS BASE 1.4 pins ( #12770 )
2018-12-30 10:40:22 -06:00
Roxy-3D
3a16cb6d7f
Slightly Slower Max X Axis speed
...
On some T-Rex 2+ machines the previous max step rate could lose steps....
2018-12-28 09:14:48 -06:00
Ludy
814d93c7cf
Fix G33 sprintf output warning ( #12738 )
2018-12-27 18:05:42 -06:00
Ludy
3877bf9704
Fix compile error with delta and sensorless homing ( #12740 )
2018-12-27 17:51:22 -06:00
Ludy
cfc5e96b4b
Move JD to Config.h (and fix jerk->eeprom bug) ( #12720 )
2018-12-27 15:29:39 -06:00
Roman Moravčík
594898aea7
Limit hotend / bed temperature to maxtemp-15 ( #12713 )
2018-12-27 11:46:05 -06:00
InsanityAutomation
530ef5846f
Make nomove=false for toolchange on filament swap ( #12739 )
2018-12-27 11:38:35 -06:00
InsanityAutomation
14ddda285c
Confirmation on Abort SD print ( #12717 )
2018-12-27 11:36:39 -06:00
Msq001
f8c5d31864
Bugfix 2.0.x add motherboard pins define ( #12689 )
...
- `pins_BIQU_B300_V1.0.h` defines pins for B300, as found in the BIQU Thunder 3D printer.
- `pins_BIQU_SKR_V1.1.h` defines pins for bigtree/BIQU SKR V1.1 motherboard.
2018-12-27 10:52:35 -06:00
InsanityAutomation
b7a8dcc35d
Update Formbot T-Rex 3 pins ( #12662 )
2018-12-20 17:32:39 -06:00
Ludy
f7127c44f8
Wanhao Duplicator i3 Plus pins create ( #12701 )
2018-12-20 17:30:36 -06:00
jmz52
33abb86b7e
Add support for MKS Robin board ( #12650 )
...
Implement initial support for MKS Robin (STM32F103ZET6) board.
Custom build script is used to generate encrypted firmware compatible with original MSK Robin bootloader (i.e. safe firmware update from SD card and possibility to go back to original close-source firmware).
2018-12-20 17:23:27 -06:00
InsanityAutomation
367a9f65aa
Add Formbot 350c Thermistor ( #12661 )
2018-12-20 17:04:17 -06:00
Ludy
33f3c75213
GTM32 Pro VB FAN-PIN correction ( #12666 )
2018-12-20 16:42:15 -06:00
Scott Lahteine
9d59a9c840
Followup to #12691 (typo)
2018-12-20 16:38:32 -06:00
Ludy
3829d6ccf8
FYSETC F6 13 - E2_SERIAL_TX_PIN correction ( #12667 )
2018-12-20 16:11:33 -06:00
Kadah
d35dcafa3d
Added MKS MINI 12864 support to FYSETC F6 V1.3 ( #12656 )
2018-12-20 16:10:49 -06:00
Roman Moravčík
98cf546771
Limit set hotend temperature to maxtemp. ( #12690 )
2018-12-20 15:56:37 -06:00
Roman Moravčík
4dad489a50
[2.0.x] Limit PID autotune target to maxtemp-15 ( #12691 )
2018-12-20 15:55:30 -06:00
Marcio Teixeira
8dcc28c9ae
Squelch warning mentioned in #11061 ( #12676 )
2018-12-20 15:34:24 -06:00
Ondřej Nový
4c8a6eee7b
[2.0.x] Update Czech translation ( #12683 )
2018-12-20 15:28:46 -06:00
Ondřej Nový
fcaed685b2
[2.0.x] Set DEFAULT_NOMINAL_FILAMENT_DIA to 1.75 in Anet A6 config ( #12664 )
2018-12-18 13:35:59 -06:00
Ondřej Nový
0572be9439
[2.0.x] Enable PIDTEMPBED in Anet A8 example config ( #12655 )
2018-12-18 13:34:46 -06:00
Luc Van Daele
c6e09c2689
[2.0.x] G33 clean up ( #12648 )
...
Remove obsolete workarounds in G33 for the now fixed zprobe_zoffset bug
2018-12-18 12:43:38 -06:00
teemuatlut
7a5e637a37
Add spreadCycle parameter sets ( #12645 )
2018-12-18 12:42:14 -06:00
Marcio Teixeira
902d5b0f8b
Allow ExtUI to use LCD_SET_PROGRESS_MANUALLY ( #12628 )
2018-12-12 17:21:37 -06:00
Dave Johnson
9a4a463ec4
Sanity-check LIGHTWEIGHT_UI, move comment up ( #12630 )
2018-12-12 16:59:20 -06:00
teemuatlut
55144284c2
TMC connection test, spreadCycle parameters, improved debugging ( #12616 )
2018-12-09 20:54:48 -06:00
Ludy
97de9d54a5
Fix broken pins file include ( #12617 )
2018-12-09 19:06:03 -06:00
Ludy
a7b3a61424
Improve some config comments readability ( #12615 )
2018-12-09 19:02:42 -06:00
Scott Lahteine
daf07e4200
Align classic bed icon consistently
2018-12-09 12:00:10 -06:00
MasterPIC
3bb8b3529a
Center ABL grid on bed with H parameter. ( #12610 )
2018-12-09 11:24:48 -06:00
