zaubentrucker/muele-marlin
1
0
Fork 0
Code Issues Pull requests Actions Packages Projects Releases Wiki Activity
4399 commits 1 branch 0 tags 156 MiB
Commit graph

895 commits

Author SHA1 Message Date
Scott Lahteine f209b755a5 Move the Z probe as far as needed to trigger the switch (PR#2461) 2015-07-16 20:02:44 -05:00
Scott Lahteine 0f1df62389 Fixup comments in code_seen 2015-07-16 16:40:52 -05:00
Scott Lahteine 2945eb6650 Call code_seen only once per parameter 2015-07-16 16:40:52 -05:00
Scott Lahteine db23b9b184 Minor tweak to M204 code (PR#2457) 2015-07-16 16:35:13 -05:00
Scott Lahteine 81d42406b7 Move braces in homeaxis to prevent a hanging else (PR#2451) 2015-07-16 10:25:54 -05:00
AnHardt ed6598adf5 Corrected Bed Height vs. Bed Topology for verbosity > 3 
and cleaned out some tabs.

Everything else is a rebased PR#2017 as proposed by @CptanPanic
 2015-07-15 19:51:40 -05:00
brian 62302ceb9e Add calculation of difference between auto-correct bed level plane, and measured topo map. 2015-07-15 19:51:40 -05:00
AnHardt 49609f6c14 Activate the new servo.move() function 
by replacing the sequences (attach, write, delay, detach), and their conditions with the new function in Marlin.main.cpp
and removing the old configuration in the ABL part of Configuration.h
 2015-07-15 17:39:43 -05:00
Scott Lahteine 87a872e103 Use st_get_position_mm where possible (PR#2411) 2015-07-12 22:15:54 -05:00
Scott Lahteine 2e0da8abdc Allow N to take a negative argument (PR@2402) 2015-07-12 22:14:25 -05:00
Scott Lahteine 447dbd6fa5 Add STEPPER_RESET_PIN support 2015-07-11 16:04:11 -05:00
Scott Lahteine 6b1b8cb2b3 Also nullify spaces before the checksum asterisk (PR#2409) 2015-07-10 09:03:07 -05:00
Scott Lahteine 4e9d658141 Prevent a hanging SERIAL_ECHO_START in M111 2015-07-07 06:59:10 -05:00
Scott Lahteine 6b494c1535 Use disable_all_heaters in M111 2015-07-07 06:59:10 -05:00
Scott Lahteine 15190d40df Add extra EOL after M111 2015-07-07 06:59:10 -05:00
AnHardt d421f5250d Correct the sign of zprobe_zoffset for G29 (PR#@391) 
Sign flipped with #2167.
See also comments
https://github.com/MarlinFirmware/Marlin/issues/2040#issuecomment-118568355
and following.
 2015-07-07 06:55:33 -05:00
Scott Lahteine 52fcc743ab Replace "target" with "destination" in M600 (PR#2374) 
- Also fix a bug in `M600` where `Z_MAX_ENDSTOP_INVERTING` is being
used as the index into the `destination[AxisEnum]` array.
 2015-07-04 05:55:25 -05:00
AnHardt 23c8c5348f Z-height fix V2b (PR#2351) 
here the other two occurences of `Z_PROBE_OFFSET_FROM_EXTRUDER` are
replaced with `zprobe_zoffset`.
 2015-07-02 20:30:40 -05:00
Todd Swindoll a111fbbd0a z-probe offset fix (PR#2361) 
verified via 1.0.2 tag that compiles by multiple people,
credit for the fix goes to paulusjacobus for the initial find and
sniffle for the correction so M851 works.
 2015-07-02 20:28:07 -05:00
Scott Lahteine 9682ed455e Fix comment on M83, add comment to prepare_move 2015-06-28 08:20:19 -05:00
AnHardt 36746143a1 Correct output of M48 (PR#2336) 
n_samples is an uint8_t .
Got printouts like:
50 of 2  ...
 2015-06-27 06:08:40 -05:00
Scott Lahteine f6ca5a8da8 Allow "M110 N123" without a checksum 2015-06-26 18:13:54 -05:00
Scott Lahteine aaad65ff5d Include a comment documenting M110 2015-06-26 18:13:54 -05:00
Scott Lahteine 862c72b030 Put the mandatory test of gcode_N first 2015-06-26 18:13:54 -05:00
Scott Lahteine 30976f9773 Allow M110 to handle a second N argument 2015-06-26 18:13:53 -05:00
Scott Lahteine 5ccb1c9e7d Use millis for M600 audio feedback interval 2015-06-25 20:45:03 -05:00
Scott Lahteine fb16a83b8a Cleanup M600 documentation comments 2015-06-25 20:45:03 -05:00
Scott Lahteine 97ec224d72 Replace target with destination in M600 2015-06-25 20:45:03 -05:00
Scott Lahteine 4ce9ddbb74 Check the temperature before filament change 2015-06-25 20:45:03 -05:00
AnHardt 722829b058 Move buzzing code to buzzr.h & buzzer.cpp (PR#2307) 
at least the lcd independent part from Marlin_main.cpp.
 2015-06-22 22:31:48 -04:00
schlotzz 1e9cf905c7 Enable ZigZag AutoBedLeveling on Deltas (PR#2273) 
ZigZag has been disabled by fault due to do_topography_map
 2015-06-15 20:26:25 -05:00
AnHardt 6ab7b560af Rework buzzing (PR#2296) 
by:
Moving HAS_LCD_BUZZ macro to Coditionals.h
Renaming HAS_LCD_BUZZ to HAS_BUZZER to make clear is has nothing to do with the lcd.
Removing the ULTRALCD condition.

Moving declaration of lcd_buzz() out of the ULTRA_LCD block in ultralcd.h
Moving definition of lcd_buzz() out of the ULTIPANEL block in ultralcd.cpp
Renaming lcd_buzz() to buzz() to make clear is has nothing to do with the lcd.

All buzzing code is now only dependent on the existence of a BEEPER-pin or the definition of a LCD_USE_I2C_BUZZER.

To do: Check the conditions for the BEEPER-pin in all pin-files.
 2015-06-15 06:13:26 -05:00
Scott Lahteine 29122db2fa Fix ULTRA_LCD spelling in HAS_LCD_BUZZ 2015-06-15 06:12:34 -05:00
Scott Lahteine e2a4a83586 Don't re-apply Z_RAISE_BETWEEN_PROBINGS in probe_pt (PR #2281) 2015-06-12 22:39:35 -05:00
MagoKimbra eb81982fcd Fix error next command in autotune (PR#2274) 
Now send only temperature for T or B, but not send OK.
Host interprets the line to show the right temperature, but not in
response to M105 then stop and send commands until it ends the autotune.
 2015-06-12 07:10:38 -05:00
AnHardt 55b23c896a Optimise out_of_range_error() (PR#2265) 
by avoiding the strncopy()
 2015-06-12 02:20:40 -05:00
AnHardt 45642b7fe8 Respect DISABLE_AXIS settings (PR#2216) 
when DEFAULT_STEPPER_DEACTIVE_TIME is over
instead of simply turn off all.
 2015-06-11 11:35:05 -05:00
Scott Lahteine 962b107341 Prevent current_command_args from bypassing nul (PR#2270) 2015-06-09 16:07:10 -05:00
Scott Lahteine ff6081be3a Parse N[0-9]+[ ]* differently (PR #2263) 
More general solution to skip N[0-9]+[ ]* in the parser as in #2218
 2015-06-08 17:06:49 -05:00
Scott Lahteine 96a3fba8ac Reverse the sign of zprobe_zoffset 
- When editing on the LCD, minus now means below the nozzle
- Stores the opposite sign in EEPROM, so bumped to “V20”
 2015-06-08 05:09:27 -05:00
paclema 8d295547be * Auto filament change on CHANGEFILAMENT feature. Now you can activate this option that extrude filament until you press the button. 2015-06-06 19:45:45 -05:00
Richard Wackerbarth ad09d6a60f 3 Step Allen Key Probe 2015-06-06 17:48:27 -05:00
AnHardt e400fce271 Merge pull request #2221 from MagoKimbra/Dryrun 
Insert Debug DRYRUN Repetier Host compatible
 2015-06-03 12:30:48 +02:00
AnHardt c3fe6e61ae Merge pull request #2229 from AnHardt/position-out-of-range 
Fix out_of_range_error()
 2015-06-03 09:46:22 +02:00
AnHardt d1f4471000 Merge pull request #2146 from Wackerbarth/Versioning 
Versioning
 2015-06-02 18:31:21 +02:00
AnHardt 17b0ec84ed Fix out_of_range_error() 
For sprintf_P() the first parameter has to be a `char*` not `const char*`.
 2015-06-02 11:50:32 +02:00
AnHardt 35af5ef23e Merge pull request #2225 from Wurstnase/naming 
consistency name for multiplier
 2015-06-02 10:18:22 +02:00
wurstnase e7e964432b consistency name for multiplier 
replace extruder_multiply with extruder_multiplier
like feedrate_multiplier or volumetric_multiplier
 2015-06-01 22:33:22 +02:00
MagoKimbra 76306f9073 Insert Debug DRYRUN Repetier Host compatible 2015-06-01 18:34:45 +02:00
MagoKimbra 881146bc22 Fix problem Width Cura 2015-06-01 17:25:32 +02:00
AnHardt 9d2a980bcf Merge pull request #2170 from thinkyhead/beep_M600_elsewise 
Slight size reduction by adding idle()
 2015-05-30 12:42:32 +02:00
AnHardt 2728dc0606 Merge pull request #2194 from thinkyhead/reduce_strings 
Redo "invalid extruder" to save 304 bytes
 2015-05-30 11:05:08 +02:00
Scott Lahteine be5236e839 Reduce setTargetedHotend by removing the switch 2015-05-29 18:03:58 -07:00
Scott Lahteine 06f401e7e5 Redo "invalid extruder" to save 264 bytes 
- Use `setTargetedHotend` in `M200`, as with other commands that use
`T` for the extruder
- Synthesize the "invalid extruder" message, obviating several long
strings
 2015-05-28 22:25:28 -07:00
Scott Lahteine 1a882bcc2e Merge pull request #2193 from thinkyhead/ignore_unrecognized_commands 
Ignore unknown commands if they start with G, M, or T
 2015-05-28 22:03:48 -07:00
Scott Lahteine a672872717 Merge pull request #2187 from AnHardt/MAX6675M105 
Print active extruder with M105 for MAX6675
 2015-05-28 18:12:48 -07:00
Scott Lahteine 9beed830eb Drop commented code_is_good lines 2015-05-28 17:53:47 -07:00
Scott Lahteine 068d4a1eb2 Ignore unknown commands if they start with G, M, or T 2015-05-28 17:44:09 -07:00
Scott Lahteine c5c9d12630 Merge pull request #2183 from AnHardt/displayinit 
Initialize the display earlier
 2015-05-28 16:29:18 -07:00
Scott Lahteine 0564625757 Update M33 for new gcode parser 2015-05-28 14:17:39 -07:00
AnHardt af7e3f5076 Print active extruder with M105 for MAX6675 
Was omitted when T0 is a MAX6675.
 2015-05-28 19:03:16 +02:00
AnHardt f0523b5816 Initialize the display earlier 
to have it ready to display errors during (temperature)-setup.
 2015-05-28 16:08:17 +02:00
Scott Lahteine 03d5709b09 M110 is a known command 
- The command parser now displays “unknown command” in more cases.
Known commands must be added to the `switch` inside `process_commands`
to suppress the error.
 2015-05-26 20:31:18 -07:00
Scott Lahteine d76a01194d Slight size reduction by adding idle() 2015-05-26 20:08:21 -07:00
Richard Wackerbarth 5ea139fd79 Revised Versioning mechanism 2015-05-25 15:53:14 -05:00
Scott Lahteine 68f6f149d0 Reduce code size with out_of_range_error function 
- Affects code size when automatic bed leveling is enabled
 2015-05-24 20:18:02 -07:00
Scott Lahteine b55f8718c3 Indent G90/G91, G92 2015-05-22 17:34:08 -07:00
Scott Lahteine b0d520b109 Indent G30, G31/G32 2015-05-22 17:33:17 -07:00
Scott Lahteine ffe27a6225 Indent G29 2015-05-22 17:32:46 -07:00
Scott Lahteine 86083badc2 Indent G4, G10/G11, G28 2015-05-22 17:32:27 -07:00
Scott Lahteine 47d7a9cb5e Indent G2/G3 2015-05-22 17:31:38 -07:00
Scott Lahteine 350f239d84 Indent G0/G1 2015-05-22 17:31:24 -07:00
Scott Lahteine 15a2351675 No need for +1 on initial seen_pointer 2015-05-22 15:31:30 -07:00
Scott Lahteine 550dd87b2a Set seen_pointer before calling code_value 2015-05-22 15:11:48 -07:00
Scott Lahteine 04a1622172 Merge pull request #2127 from Wackerbarth/Kossel_Pro 
Kossel Pro
 2015-05-21 18:43:26 -07:00
Scott Lahteine f919a2fed1 Merge pull request #2134 from AnHardt/preheat-all 
Shift call of start_watching_heater() into setTargetHotend()
 2015-05-21 18:36:28 -07:00
AnHardt 0c0ace2a04 Remove start_watching_heater() fom M104 and M109 2015-05-22 01:44:50 +02:00
Scott Lahteine bde9c70d42 Suppress the line mismatch error after M303 2015-05-21 16:27:22 -07:00
Scott Lahteine 50bd7493cc Merge pull request #2108 from thinkyhead/m33_long_filename_host_support 
M33 LONG_FILENAME_HOST_SUPPORT
 2015-05-21 16:22:47 -07:00
Scott Lahteine 4d11b29959 Merge pull request #2113 from thinkyhead/command_sanitizer 
Command sanitizer
 2015-05-21 16:21:58 -07:00
Richard Wackerbarth 735bf2d35f Describe Custom M Code 2015-05-21 08:06:33 -05:00
Scott Lahteine f39658c822 M120 and M121 are reversed 2015-05-21 00:17:44 -07:00
AnHardt 89d2ee6f13 Make output on display dependant of ULTRA_LCD 2015-05-20 22:03:16 +02:00
AnHardt f4a93ed997 Add a string parameter to kill() 
Makes the output on the LCD adjustable.
 2015-05-20 20:53:48 +02:00
Scott Lahteine a0f362c735 Simplify & optimize with current_command_args 2015-05-18 07:08:04 -07:00
Scott Lahteine adc8fcb77f More parser comments, optimize code_seen, save with goto 2015-05-18 07:08:04 -07:00
Scott Lahteine c6d8dd19d9 use fetched value 2015-05-18 07:08:04 -07:00
Scott Lahteine 1116e13f5a Further optimization of command parser 2015-05-18 07:08:03 -07:00
Scott Lahteine 3a4c3ab76e Pre-sanitize the command before handling 
- Use a global pointer for the current sanitized command
- Pre-sanitize the current command to bypass `N` and nullify `*`,
removing the need for handlers to bypass, ignore, or nullify these
parts, and reducing overhead for `code_seen`, etc.
- Pre-skip leading whitespace.
- Only look for G, M, T codes at the start of the command.
- Verify that G, M, T codes are followed by command codes.
 2015-05-18 07:06:51 -07:00
Scott Lahteine 0f2c9bacfd M33 LONG_FILENAME_HOST_SUPPORT 2015-05-17 17:36:32 -07:00
Scott Lahteine 3feaef6526 Have G92 set the nozzle position on Delta and SCARA 2015-05-17 17:08:05 -07:00
Scott Lahteine 6c27eaf864 Merge pull request #2101 from thinkyhead/code_style 
Code style and a dangling "else"
 2015-05-17 03:39:08 -07:00
Scott Lahteine d580a0d186 Use "+=" in plane rotation 2015-05-17 01:51:14 -07:00
Scott Lahteine 2f3a410cb0 Fix a potential hanging "else" bug 2015-05-17 01:50:30 -07:00
Scott Lahteine b83e3f0905 Combine "Bed X: " strings 2015-05-17 01:49:52 -07:00
Scott Lahteine 7dfb8becdb Adjust some names and types in Marlin_main.cpp 2015-05-17 01:48:51 -07:00
Scott Lahteine c966aa26ff Comments in Marlin_main.cpp 2015-05-17 01:47:53 -07:00
Scott Lahteine c54a2ea042 Adjust spacing in Marlin_main.cpp and stepper.* 2015-05-17 01:47:02 -07:00
Scott Lahteine 072625ccad Update headings in Marlin_main.cpp and stepper.cpp 2015-05-17 01:44:53 -07:00
Scott Lahteine 16032f149f Rename to codenum as a consistency 2015-05-16 23:17:35 -07:00
Scott Lahteine 273a4a253f Merge pull request #2096 from thinkyhead/cherry_picking3 
Hide M117 with no LCD
 2015-05-16 21:10:28 -07:00
Scott Lahteine 64825a3d1e Merge pull request #2095 from thinkyhead/cherry_picking2 
Add gcode_line_error to reduce code size
 2015-05-16 21:09:15 -07:00
Scott Lahteine ca79282eaf Hide M117 with no LCD 2015-05-16 20:59:04 -07:00
Scott Lahteine ce218cafdb Add gcode_line_error to reduce code size 2015-05-16 20:54:58 -07:00
Scott Lahteine 46d59784ad Rename preocess_command to process_next_command 2015-05-16 20:47:40 -07:00
Scott Lahteine 19166a92e4 Merge pull request #2057 from Wurstnase/serial_wait 
add plan buffer remaining for 'P' and block buffer remaining 'B'
 2015-05-14 04:57:08 -07:00
Scott Lahteine e97fcafd0e Merge pull request #2076 from thinkyhead/mendel_inverting 
Use MSG_OK in M105
 2015-05-14 04:54:11 -07:00
Scott Lahteine 0f6cd3640b Drop extraneous ok_to_send 2015-05-14 04:38:09 -07:00
Scott Lahteine 0ce355d9e7 Use MSG_OK in M105 2015-05-14 03:33:38 -07:00
Scott Lahteine 7b3acfbb6f Merge pull request #2072 from thinkyhead/better_arc_code 
Consolidate arc code, remove motion_control.*
 2015-05-14 00:27:22 -07:00
Scott Lahteine 68ce419147 Note on segment size 2015-05-13 19:11:36 -07:00
Scott Lahteine 8b92249f18 Bring arc_offset into auto scope 2015-05-13 19:00:46 -07:00
Scott Lahteine 80807b2d71 Consolidate arc code, remove motion_control.* 2015-05-13 18:52:41 -07:00
Scott Lahteine f65833931d Formatting tweaks 2015-05-13 02:02:19 -07:00
Scott Lahteine 747fd5801c Merge pull request #2055 from thinkyhead/thermal_unified 
Combine thermal runaway and watch-period
 2015-05-12 08:04:29 -07:00
Scott Lahteine 6e5572228d Merge pull request #2064 from thinkyhead/wait_before_g28 
Split up prepare_move by type
 2015-05-12 07:53:11 -07:00
Scott Lahteine 27ad381e25 Allow fractional seconds in G4 and M0 2015-05-12 07:52:08 -07:00
Scott Lahteine b2bd9aae7c SCARA_SEGMENTS_PER_SECOND 2015-05-12 04:18:15 -07:00
Scott Lahteine bd20bd5444 Merge pull request #2063 from chris-bo/autobed_sled 
improve sled handling
 2015-05-12 03:29:21 -07:00
Scott Lahteine 9e95ceb3fc Split up prepare_move by type 
- For better encapsulation add inlines for each prepare_move type
- Move controllerFan vars inside the function as statics
- Some formatting cleanup
- Rename `ClearToSend` as `ok_to_send`
 2015-05-12 02:08:20 -07:00
Christian Bohn f48599f172 add pin definition to some motherboards 2015-05-12 10:02:23 +02:00
Scott Lahteine b5200e184c Remove extra setup_for_endstop_move 2015-05-12 01:01:53 -07:00
Scott Lahteine 8d814de558 Return void in prevent_dangerous_extrude 2015-05-12 00:55:00 -07:00
Scott Lahteine 367e2eb9f4 Global setup_for_endstop_move 2015-05-12 00:51:22 -07:00
Scott Lahteine fa951f8a0b Always do st_synchronize() before G28 2015-05-12 00:31:51 -07:00
Christian Bohn 27a3b1d895 disable sled pin by default 2015-05-12 08:51:01 +02:00
Christian Bohn fb44b53ae3 sled improvements 
- create sled pin definition
- G28 Works with sled
 2015-05-11 23:22:19 +02:00
Wurstnase 46d1932380 add plan buffer remaining for 'P' and block buffer remaining 'B' 2015-05-11 13:04:00 +02:00
Scott Lahteine 8a0dc4d54a Merge pull request #1922 from Wurstnase/serial_wait 
Serial wait
 2015-05-10 23:10:25 -07:00
Wurstnase 526ad82d20 activate advanced_ok and no_timeout 2015-05-11 08:01:51 +02:00
Scott Lahteine 2445ae3d3a Combine thermal runaway and watch-period 
- Make thermal protection for all hotends and/or bed into simple
switches
- Now enable `WATCH_TEMP_PERIOD` when `THERMAL_PROTECTION_HOTENDS` is
enabled
- Move detailed thermal parameters to `Configuration_adv.h`
- Add sanity checks to warn about old configurations
- Change `WATCH_TEMP_PERIOD` to seconds instead of milliseconds
 2015-05-10 22:52:01 -07:00
Scott Lahteine 4097207c75 Merge pull request #2041 from thinkyhead/watch_temp 
More thermal protection
 2015-05-10 21:39:05 -07:00
Scott Lahteine 9b3d4380d3 Only watch the heater that was set 2015-05-10 20:26:45 -07:00
Scott Lahteine f73f4ce555 Make some z probe and servo code tweaks 2015-05-09 19:11:19 -07:00
Scott Lahteine 54deb9eea3 Enable WATCH_TEMP_PERIOD by default 2015-05-08 22:36:02 -07:00
Wurstnase 0cb87795a3 advanced 'ok' 
ok N(linenumber) P(bufferremaining)
the host can use this to send the data much faster.

Some pseudo code:
If (bufferremaining > 0)  send command
## as long there is free buffer send command

Also
if (linenumber > lastsend - bufferremaining) send command
## as long last linenumber received is bigger than lastsend (host) - last bufferremaining received
 2015-05-08 22:28:51 +02:00
Wurstnase 182e0d99c9 Merge remote-tracking branch 'Marlin8bit/Development' into serial_wait 2015-05-08 21:27:18 +02:00
Scott Lahteine 7f3252eea9 Merge pull request #1999 from paclema/Filrunout_configurable_script 
Added configurable script for filrunout from configuration.h
 2015-05-08 04:39:59 -07:00
Scott Lahteine 79633a74ab Fix MBL compile error 2015-05-06 14:25:13 -07:00
Scott Lahteine 777f2d3820 Merge pull request #2018 from fmalpartida/bugFixing 
Bug corrected: persistent HOMING message when HOME button pressed for homing.
 2015-05-05 00:12:32 -07:00
Scott Lahteine ecb46de349 Merge pull request #2013 from bq/Fix_lowercase 
Fixed lowercase change missing on commit a22a228b.
 2015-05-04 23:50:56 -07:00
fmalpartida 150a35eff8 Bug corrected: 
Persistent homing message.
Message was declared as an alert, therefore it was persistent.
Updated to message.
 2015-05-04 19:48:49 +02:00
Gina Häußge ab246ab032 Reverting changes to error messages on serial console 
This reverts the changes done to the error message for line number mismatches done in commit d43cc2dd5f
 2015-05-04 15:03:00 +02:00
Ivan Galvez Junquera 59529b755d Fixed lowercase change missing on commit a22a228b. 
Servo.cpp and Servo.h were changed to lowercase in Makefile but not their actual filenames.
 2015-05-04 09:44:34 +02:00
Scott Lahteine 1f039cde61 Merge pull request #1992 from thinkyhead/too_many_probes 
Stow Z probe on M402 without extra raise
 2015-05-03 20:40:26 -07:00
Scott Lahteine ca8cec8e8a Merge pull request #1998 from paclema/Filament_runout_fix 
Fixed sintaxis error of filament runout
 2015-04-29 19:53:25 -07:00
Scott Lahteine d4c74b8f8c Don't apply M428 if an error occurs 
- Also move audio feedback into the command
- Added shorthand for `lcd_buzz` availability
 2015-04-29 19:05:48 -07:00
Scott Lahteine d065d37822 Add M428 to set home_offset logically 2015-04-29 18:26:16 -07:00
paclema 013a09dbe6 Added configurable script for filrunout form configuration.h 2015-04-29 21:38:40 +02:00
paclema 4dcc0fd55a Fixed sintaxis error of filament runout 2015-04-29 21:32:27 +02:00
Scott Lahteine ce3caf447b Tweak how homeaxis deploys and stows 2015-04-28 19:17:48 -07:00
Scott Lahteine a235dca79c Stow z on M402 without extra raise 2015-04-28 19:10:07 -07:00
Scott Lahteine 3688256f86 Merge pull request #1974 from thinkyhead/eeprom_in_gcode 
Make EEPROM reproducible in GCode
 2015-04-27 22:35:41 -07:00
Scott Lahteine 31516e2a3b Merge pull request #1985 from Arengorn/Development 
Update of servo.h
 2015-04-27 22:10:02 -07:00
Scott Lahteine 0f687b5dda Merge branch 'Development' into eeprom_in_gcode 
Latest upstream commits
 2015-04-27 21:47:47 -07:00
Scott Lahteine 28aef684b4 Merge pull request #1957 from Voxel8/sjk/home_y_before_x 
Allow Y to home before X with option in Configuration_adv.h.
 2015-04-27 21:41:14 -07:00
Scott Lahteine 71a0b1a5bb Disable endstops between homing bumps 2015-04-27 21:14:30 -07:00
Scott Lahteine c36226c4dc Fix homing Z position 
Add `sync_plan_position()` after `axis_is_at_home(axis)` to keep the
planner position in sync when homing.
 2015-04-27 20:55:19 -07:00
Scott Lahteine ff178d8cf7 Change M421 to take coordinates 
This makes `M421` more amenable for irregular matrices
 2015-04-27 19:48:34 -07:00
Bernardo ff67ee73fc Update Marlin_main.cpp 
Corrected "servo.h" to "Servo.h" because of the updated filename.
 2015-04-27 23:29:16 -03:00
Steve Kelly 98ca46006c Allow Y to home before X with option in Configuration_adv.h. 
This addresses comments in #1956 and #1079. In particular, this is useful
when both endstops are stationary on a CoreXY system, and the Y axis needs
to be homed before the X so the flags are aligned.
 2015-04-27 16:17:30 -04:00
Scott Lahteine 0fca084ea6 Make EEPROM reproducible in GCode 
With these changes the output of `M503 S0` is all you need to restore
the EEPROM. Building on this it is straightforward to save and restore
the EEPROM state using the SD card or external GCode file.

- Added `M145` to set “heatup states” for the LCD menu
- Added `M420` to toggle Mesh Bed Leveling
- Added `M421` to set a single Mesh coordinate
- Extended `Config_PrintSettings` with added M codes
- Cleaned up some comments here and there
 2015-04-26 20:56:33 -07:00
Scott Lahteine d43cc2dd5f M111 - Debug Level 
- Add `M111` as a standard option to set the debug level
- Implement `DEBUG_ECHO` in `process_commands`
- Other debug levels (e.g., `DEBUG_DRYRUN`) need more work
 2015-04-26 20:08:45 -07:00
Scott Lahteine a22a228bcc Rename files to move them in the IDE 2015-04-25 21:04:54 -07:00
Scott Lahteine 0438f0d835 Merge pull request #1924 from thinkyhead/raise_z_for_m401_m402 
Raise Z for M401 and M402
 2015-04-24 22:41:12 -07:00
Scott Lahteine b275946a52 Merge pull request #1966 from thinkyhead/g4_dwell_message 
G4 shows status message only if no message is set already
 2015-04-24 22:02:37 -07:00
Scott Lahteine 182f2cda35 Minor cleanup of M48 2015-04-24 21:26:36 -07:00
Scott Lahteine 3a6fd912cd Latest upstream commits, merged 2015-04-24 21:14:13 -07:00
Scott Lahteine 3c9e94e035 Merge pull request #1964 from AnHardt/Max6675again 
Add variant for MAX6675 in M104
 2015-04-24 20:44:45 -07:00
Scott Lahteine 56ff46eb8b Improve code_has_value test 2015-04-24 20:43:16 -07:00
Scott Lahteine ce142afdda G4 shows status message only if no message is set already 
- Address issue raised in #1961
 2015-04-24 20:13:01 -07:00
Scott Lahteine 35e79d56a5 Remove set-coordinate extension of G28 2015-04-24 19:23:12 -07:00
Scott Lahteine 3a74bb5039 Merge pull request #1945 from Wurstnase/max_endstopp 
Max endstopp
 2015-04-24 19:17:38 -07:00
AnHardt 0fed46360c Add variant for MAX6675 in M104 
Else will throw error:
@:0 B@:0
Error:No thermistors - no temperature
[ERROR] Error:No thermistors - no temperature

when no bed is defined
 2015-04-24 16:43:19 +02:00
Scott Lahteine 588ed70d4a Latest upstream commits, merged 2015-04-23 21:18:48 -07:00
Scott Lahteine 0165560333 Apply zprobe_zoffset in axis_is_at_home 
Ensure the probe offset will always be included when homing Z.
 2015-04-23 21:12:38 -07:00
Scott Lahteine 075386e7fe Merge pull request #1959 from thinkyhead/lcd_move_rate 
Include axis parameter to ultralcd's line_to_current
 2015-04-23 21:06:57 -07:00
Scott Lahteine 2558c10c6c Use the slower feedrate for XY axes 2015-04-23 20:06:17 -07:00
Scott Lahteine 64268f3312 Fixup axis_is_at_home a little 2015-04-23 18:16:44 -07:00
Scott Lahteine 996d0a9185 Squish the code down a little 2015-04-23 18:06:36 -07:00
Scott Lahteine 8534bc376c Fix homing of YZ with DUAL_X_CARRIAGE 2015-04-23 17:56:37 -07:00
Scott Lahteine 3b97a7d446 Merge pull request #1944 from AnHardt/beep2 
More Beeper clean up
 2015-04-23 17:50:02 -07:00
Wurstnase be9e4ceddc fix typo 
c'n'p ftw :/
 2015-04-23 10:35:14 +02:00
unknown c26d816839 filter any 0 2015-04-22 12:09:57 +02:00
Wurstnase 61ae43f35e v <-> code_value 2015-04-20 23:31:10 +02:00
Wurstnase da0d91a79b max endstopp 
no user will home to 0 with a max endstopp
 2015-04-20 23:28:46 +02:00
AnHardt 064f2b37d0 More Beeper clean up. 
Centralised beep code to lcd_buzz().
From gcode_M300() and lcd_quick_feedback().

Enforced max. duration for M300 to 5 seconds.

Corrected description in 'Configuration.h'

LCD_FEEDBACK_FREQUENCY_HZ 0 gives now a silent delay of
LCD_FEEDBACK_FREQUENCY_DURATION_MS.
 2015-04-20 11:11:13 +02:00
Wurstnase 92575cecca new timout/add adv_ok 2015-04-20 00:22:40 +02:00
AnHardt 671aaf2dc9 Minor fix for M300 
Corrected wrong order of parameters.
 2015-04-19 13:25:20 +02:00
Scott Lahteine d931220a65 Tweak comments 2015-04-18 23:12:29 -07:00
Scott Lahteine 47847765e2 Add M410 QuickStop command 2015-04-18 23:07:48 -07:00
Wurstnase b09a957fce make 'wait' optional and mark as workaround 2015-04-16 21:42:54 +02:00
Scott Lahteine 63b98b8280 Raise Z for M401 and M402 2015-04-16 07:24:33 -07:00
wurstnase d69da22f7c last_command_time inside get_command() 2015-04-16 16:20:23 +02:00
wurstnase 574e2d856e remove config 2015-04-16 13:07:20 +02:00
paclema cde5eee2a5 Removed unnecessary comments 2015-04-15 19:01:09 +02:00
paclema e1b69db6d1 Fixed M48 mismatch between n and P parameter on documentation 2015-04-15 18:17:58 +02:00
Scott Lahteine e0e68c5cbc Rename servos[] array in Marlin to servo[] 2015-04-14 03:13:25 -07:00
Scott Lahteine 642f6a92bc fix type of code_has_value 2015-04-13 18:02:17 -07:00
Scott Lahteine 17ad80c1e1 Spacing in XYZ_CONSTS 2015-04-13 17:58:47 -07:00
Scott Lahteine 09d60e0128 Naming and code comments 2015-04-13 17:17:36 -07:00
Mehmet Sutas 5a9e45cc4a Fix Syntax Error Filament Runout Statement 2015-04-13 22:37:18 +03:00
Scott Lahteine ccddc280be Apply three more commits 2015-04-12 22:47:44 -07:00
Scott Lahteine ac2b23f574 Homing fixes 
- Prevent `Z_SAFE_HOMING` from homing Z twice in some cases
- Allow `G28` with XYZ values of 0 to explicitly set the position
- Don’t add `home_offset` when setting XYZ explicitly in `G28`
- Add `code_has_value` function to check for the presence of a numeric
value (could just test for space or nul to allow other types of values)
 2015-04-11 20:06:48 -07:00
Scott Lahteine 5fe382949b Some G-Codes comment cleanup 2015-04-10 16:16:13 -07:00
Scott Lahteine 8b16ebe705 Break out prevent_dangerous_extrude feature 
- It’s inline here, but could be a macro and duplicated for
`planner.cpp`
 2015-04-09 22:40:37 -07:00
Scott Lahteine 9189cc66ab Fix moves for DELTA for MANUAL_BED_LEVELING 
- Use `line_to_current` in place of `plan_buffer_line`
 2015-04-09 04:32:14 -07:00
Scott Lahteine 2ca099d1e7 Merge pull request #1876 from thinkyhead/cold_extrude 
Catch dangerous extrude before trying several
 2015-04-09 03:21:19 -07:00
Scott Lahteine a00ebf03d4 Merge pull request #1868 from AnHardt/LCD_STR 
Moved the definitions of the LCD_STR_* to Conditionals.h
 2015-04-09 01:56:23 -07:00
Scott Lahteine 1269c445ab Catch dangerous extrude before trying several 2015-04-09 01:40:48 -07:00
AnHardt 540dbb35e2 And an other MSG_BED in Marlin_main.cpp 2015-04-09 01:16:06 +02:00
AnHardt 14d4419e16 Replaced SERIAL_PROTOCOLPGM(MSG_BED) with SERIAL_PROTOCOLPGM("Bed") 
Resolved some warnings in Marlin_main.cpp regarding compares of signed and unsigned integers by replacing 'int' or 'uint16_t' with 'uint8_t'.
 2015-04-08 23:59:01 +02:00
AnHardt 6a514f3dc9 Aplied HAS_LCD_CONTRAST also to Marlin_main.cpp 
and cleaned typo.
 2015-04-08 13:26:29 +02:00
Scott Lahteine 3162971cd6 current_position not static 2015-04-08 01:05:39 -07:00
Scott Lahteine 27cb90da8b IsStopped / IsRunning inline 2015-04-08 00:56:19 -07:00
Scott Lahteine e03da4805b Merge pull request #1774 from epatel/Development 
Mesh bed leveling: Added G29 S3 + finer display steps during manual input + bug fix
 2015-04-07 19:24:46 -07:00
Scott Lahteine f7c4e7e19f Fix G29 not deploying in some instances 2015-04-07 15:38:29 -07:00
Edward Patel 002340f32c Merge branch 'Development-Marlin' into Development 2015-04-07 22:49:12 +02:00
Scott Lahteine c379f17117 Encapsulate setting of homing_bump_feedrate 2015-04-06 23:21:33 -07:00
Scott Lahteine d20f42c883 Don't stow the probe until the last grid point! 
- Address Issue #1682 at hash #issuecomment-89756858
 2015-04-06 20:58:09 -07:00
Scott Lahteine 6d084c017f Fix typo in FWRETRACT handler 
Should be `retracting` and not `retract`
 2015-04-06 17:04:22 -07:00
Edward Patel 2f0081bbb5 Compile error fix! Fix for merge artifacts. 2015-04-05 04:16:16 +02:00
Edward Patel ea10601406 Merge branch 'Development-Marlin' into Development 
Conflicts:
	Marlin/Configuration.h
	Marlin/Marlin_main.cpp
 2015-04-05 04:06:02 +02:00
Scott Lahteine 61f8394361 Compare indices instead of floats for probe actions 2015-04-04 05:01:16 -07:00
Scott Lahteine 0935084141 Fix manage_inactivity 
- Document `manage_inactivity` function
- Allow `EXTRUDER_RUNOUT_PREVENT` to work with all extruders
- Use faster `memcpy` for copying coordinates
 2015-04-03 23:42:50 -07:00
Scott Lahteine c065da52ec Spacing and spelling 2015-04-03 22:54:48 -07:00
Scott Lahteine 8680b515b0 Fix missing tmp_extruder -> target_extruder 2015-04-03 22:12:49 -07:00
Scott Lahteine c185912c19 Latest upstream commits, mostly 2015-04-03 21:58:48 -07:00
Scott Lahteine 1e5c18bb14 Add code_value_short and SERIAL_CHAR 2015-04-03 21:43:30 -07:00
Scott Lahteine 84e4edaea7 Add M48 comment for #1794 2015-04-03 19:52:00 -07:00
Scott Lahteine b98ebd517e disable / enable_all_steppers functions 2015-04-03 19:25:22 -07:00
Scott Lahteine 713953d8c1 Upstream commits, allow no extruder in M105 2015-04-03 19:16:38 -07:00
Scott Lahteine 8f893eb8df Merge pull request #1798 from thinkyhead/fixup_probing 
Fix probe height at G28 start
 2015-04-03 19:03:00 -07:00
Scott Lahteine dde7e11f8e Merge branch 'Development' into fixup_tr 
Latest upstream commits
 2015-04-03 18:56:52 -07:00
Scott Lahteine abd7fc36b6 Fix probe height at G28 start 2015-04-03 18:54:55 -07:00
Scott Lahteine 610c8c5471 Merge pull request #1795 from thinkyhead/fixup_probing 
Finish pin tests
 2015-04-03 18:44:44 -07:00
Scott Lahteine e4934164e4 Merge pull request #1790 from Wurstnase/fix_home_z 
fix feedrate for homing z
 2015-04-03 18:35:09 -07:00
Scott Lahteine a469d796e1 Add cleanups needed for #1772 2015-04-03 18:14:57 -07:00
Scott Lahteine c0ca26cd50 Merge branch 'Development' into fixup_probing 
Latest upstream commits
 2015-04-03 18:05:17 -07:00
Scott Lahteine 5c1f08a35f Merge pull request #1772 from croadfeldt/Merge_cleanup 
Z_PROBE_ENDSTOP
 2015-04-03 18:04:31 -07:00
Scott Lahteine 92119d0f7d Static delta[] for SCARA 2015-04-03 16:46:56 -07:00
Scott Lahteine 6b919e14c1 Group all universal variables 2015-04-03 15:45:41 -07:00
Scott Lahteine 21cd2e4fae Merge branch 'Development' into fixup_probing 
Latest upstream commits
 2015-04-03 15:32:15 -07:00
Scott Lahteine 0e8182bbf2 Additional pin tests, cleanup 2015-04-03 15:31:35 -07:00
Wurstnase 45565b680d second wrong feedrate 2015-04-03 18:01:28 +02:00
Wurstnase 581b2aae04 fix feedrate for homing z 
max_feedrate is in mm/s. line_to_destination needs a feedrate in mm/min because there is feedrate/60.
 2015-04-03 16:11:32 +02:00
AnHardt 23cd54755f Fix typo in Marlin_main.cpp 
related to current_position[Z_AXIS] and retract_zlift.

'+ =' -> '+='

Fix for #1786
 2015-04-02 14:50:31 +02:00
Scott Lahteine e96df67630 Clarify thermal_runaway_protection 
- Add comments documenting `thermal_runaway_protection`
- Add an enum for the thermal runaway states
- Add macros for temperature helper functions
- Fix a glitch with the z probe sled in homeaxis
 2015-04-02 05:10:14 -07:00
Edward Patel 6b91b7b411 Mesh bed leveling: Added G29 S3 + finer steps in manual probing. 
* Use "G29 S3 Xn Yn Zn.nn" to modify bad probed point manually
* Changed manual Z steps from 0.05 to 0.025 and made brought it to Configuration.h
 2015-04-01 21:18:51 +02:00
Chris Roadfeldt 26dc80bf2d Typo fixed... 2015-04-01 13:47:17 -05:00