Florian Heilmann
d08867986e
Add autotemp capabilities to M104
...
This allows M104 to pass the F and B parameters to enable autotemp as well
2016-11-17 11:28:19 -06:00
Scott Lahteine
2330619da0
Merge pull request #5191 from petrzjunior/const
...
Replace const bool with #define for consistency
2016-11-17 03:37:32 -06:00
Petr Zahradník junior
d7ce5d271b
Replace const bool with #define for consistency
2016-11-16 18:55:21 +01:00
Scott Lahteine
5d23e52d75
Merge pull request #5228 from thinkyhead/rc_keep_last_mix
...
Fix DIRECT_MIXING_IN_G1 to preserve the previous mix
2016-11-15 19:12:01 -06:00
Scott Lahteine
99b0c1fe56
Fix DIRECT_MIXING_IN_G1 to preserve the previous mix
2016-11-15 16:12:26 -06:00
Scott Lahteine
410657b050
Fix G30 with limits, print correct probe XY
2016-11-15 14:10:28 -06:00
Scott Lahteine
665b7f3893
Merge pull request #5212 from thinkyhead/rc_mixing_faster
...
Store mix factors as reciprocals and multiply
2016-11-12 18:47:11 -06:00
Scott Lahteine
60cc9342a4
Merge pull request #5188 from thinkyhead/rc_extended_host_support
...
Extended host support: M155 Auto temp report, M115 capabilities
2016-11-12 15:38:06 -06:00
Scott Lahteine
f663220e87
Store Mix factors as reciprocals and multiply
2016-11-12 15:19:18 -06:00
Scott Lahteine
b31a07e261
Stateful M355 with separate P parameter
2016-11-09 03:28:18 -06:00
Scott Lahteine
3c9a838651
Extended capabilities report in M115
2016-11-09 02:32:58 -06:00
Scott Lahteine
68b866b5dd
Add M155 - Auto-report temperature with interval
2016-11-09 02:32:58 -06:00
Scott Lahteine
75bfde9945
M155=>M260, M156=>M261
2016-11-08 17:54:54 -06:00
Scott Lahteine
dcfd7c69e8
Merge pull request #5163 from nzinov/RCBugFix
...
Improve G30 probing command - add optional arguments
2016-11-07 11:37:13 -06:00
Scott Lahteine
e765eebfb0
Patch spacing in bilinear grid report
2016-11-07 04:08:25 -06:00
Nikolay Zinov
dea00bbcf1
improve G30 probing
...
Add optional parameters
X, Y for probe point
S sets stowing on and off
2016-11-05 13:22:45 +03:00
Scott Lahteine
176aeafc19
Don't define bilinear_line_to_destination on kinematic setups
2016-11-03 14:10:07 -05:00
Scott Lahteine
236853df22
Corrections to bilinear_line_to_destination
...
- Allow more than 9x9 probe points
- Account for the probe starting position
2016-11-03 04:43:59 -05:00
Scott Lahteine
0115e495fe
Fix up Dual X switch blocks
2016-11-02 21:38:50 -05:00
Scott Lahteine
2495ab7af2
Make dual_x_carriage_mode an enumeration
2016-11-02 21:38:49 -05:00
Scott Lahteine
d6c36f5bb9
Fix Z raise with DXC_AUTO_PARK_MODE
2016-11-02 21:36:50 -05:00
Scott Lahteine
0c79553fc5
Cast int to AxisEnum for some accessors
2016-11-02 17:42:24 -05:00
Scott Lahteine
adbf1f7dca
Add M355 to the GCodes list.
2016-11-02 16:43:52 -05:00
Scott Lahteine
63efc10599
Merge pull request #5134 from thinkyhead/rc_bilinear_split_lines
...
Split cartesian moves on grid boundaries with bilinear ABL
2016-11-02 16:14:55 -05:00
Scott Lahteine
ee5b8d6dc8
Split moves on grid boundaries with bilinear ABL on cartesian
2016-11-01 08:25:47 -05:00
Scott Lahteine
66744a6076
Merge pull request #5133 from thinkyhead/rc_M355_case_light
...
M355 Case light
2016-11-01 07:51:27 -05:00
Scott Lahteine
955d14acb0
Patch photo pin code style
2016-11-01 06:30:14 -05:00
Stanley
ab3f966f5f
Case light G-code M355
...
implemented G-Code M355 into Marlin
2016-11-01 06:30:14 -05:00
Sebastianv650
f9bea7968f
BugFix for incorrect E-speed calculation
...
The extrusion speed was wrong due to a not high enough precision of
esteps to XY steps, therefore now the target float values are used to
calculate the ratio between XY movement and extrusion speed.
The e_speed_multiplier8 was replaced by an absolute multiplier called
abs_adv_steps_multiplier8, therefore one multiplication and bitshift can
be saved inside the stepper ISR. Due to this, also extruder_advance_k is
better suited inside the planner and not the stepper files any more.
2016-11-01 08:08:47 +01:00
Scott Lahteine
ff3a8ca0d1
Use NUM_DIGITAL_PINS instead of custom DIO_COUNT
2016-10-31 08:08:03 -05:00
Scott Lahteine
04a1fac029
Some cleanup to M43
2016-10-31 08:08:03 -05:00
Bob-the-Kuhn
c7f1f0dae6
Add endstop monitor & make pins report pretty
2016-10-31 08:08:02 -05:00
Scott Lahteine
396434a445
Fix compiler warning in M145
2016-10-28 20:57:36 -05:00
Scott Lahteine
07bfc45df8
Adjust spacing in gcode_M149
2016-10-28 20:57:36 -05:00
Scott Lahteine
1a2310c494
Make LCD preheat vars an array to reduce code size
2016-10-28 20:57:36 -05:00
Scott Lahteine
50ee749082
Centralize click-handling in the LCD loop
2016-10-28 20:57:21 -05:00
Scott Lahteine
47ad97c35e
Merge pull request #5109 from thinkyhead/rc_eeprom_M218_tool_offset
...
Save hotend_offset array (M218) in EEPROM
2016-10-28 20:08:29 -05:00
Scott Lahteine
67ab54185b
Save hotend_offset array (M218) in EEPROM
2016-10-28 18:45:23 -05:00
MagoKimbra
dfcdbb437b
Fix Command M420
2016-10-28 20:53:48 +02:00
Scott Lahteine
c34dbfb248
Merge pull request #5072 from thinkyhead/rc_preset_auto_fans
...
Add predefined AUTO_FAN_PINs to pins files
2016-10-27 17:12:11 -05:00
Scott Lahteine
c4c53856a4
Merge pull request #5094 from esenapaj/Fix-for-the-PR-#5088
...
Fix for the PR #5088 (Handle M108 in M1 also with ULTIPANEL)
2016-10-26 21:51:18 -05:00
esenapaj
d5a5042d23
Fix for the PR #5088 (Handle M108 in M1 also with ULTIPANEL)
2016-10-27 10:32:20 +09:00
Scott Lahteine
3f94b15cef
Fix bilinear grid constraints
...
Followup to #5090
2016-10-26 18:11:26 -05:00
Scott Lahteine
ada935de87
Allow TEMP_STAT_LEDS with only one LED defined
2016-10-26 17:51:26 -05:00
Scott Lahteine
f0d673561f
Fix for bilinear grid outside bounds
2016-10-26 05:00:03 -05:00
Scott Lahteine
1ba1ec0db9
Handle M108 in M1 also with ULTIPANEL
2016-10-25 23:25:47 -05:00
Greg Cormier
f0aed9dac7
Fix #4995 - M48/G29 on CoreXY maybe others?
2016-10-22 20:45:13 -04:00
Scott Lahteine
3544c3632f
Merge pull request #5062 from thinkyhead/rc_warnings_fix
...
Warnings fixed redux
2016-10-22 12:21:36 -05:00
Josef Pavlik
0bd66807b2
fixed warning: extra ;
2016-10-22 11:12:29 -05:00
Scott Lahteine
5f5a55a0de
Add a ZERO macro to clear arrays
2016-10-22 10:07:18 -05:00
