/** * Marlin 3D Printer Firmware * Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ #pragma once #define ALLOW_STM32DUINO #include "env_validate.h" #if HOTENDS > 3 || E_STEPPERS > 5 #error "MKS Monster supports up to 3 hotends and 5 E-steppers." #elif HAS_FSMC_TFT #error "MKS Monster doesn't support FSMC-based TFT displays." #endif #define BOARD_INFO_NAME "MKS Monster8 V1.x" // USB Flash Drive support #define HAS_OTG_USB_HOST_SUPPORT //#define DISABLE_DEBUG // Avoid conflict with TIMER_TONE #define STEP_TIMER 10 // Use one of these or SDCard-based Emulation will be used //#define SRAM_EEPROM_EMULATION // Use BackSRAM-based EEPROM emulation //#define FLASH_EEPROM_EMULATION // Use Flash-based EEPROM emulation #define I2C_EEPROM // Need use jumpers set i2c for EEPROM #define MARLIN_EEPROM_SIZE 0x1000 // 4KB #define I2C_SCL_PIN PB8 // I2C_SCL and CAN_RX #define I2C_SDA_PIN PB9 // I2C_SDA and CAN_TX // // Servos // #define SERVO0_PIN PA8 // Enable BLTOUCH // // Limit Switches for diag signal // #define X_DIAG_PIN PA14 // Driver0 diag signal is connect to X- #define Y_DIAG_PIN PA15 // Driver1 diag signal is connect to Y- #define Z_DIAG_PIN PB13 // Driver2 diag signal is connect to Z- #define E0_DIAG_PIN PA13 // Driver3 diag signal is connect to X+ #define E1_DIAG_PIN PC5 // Driver4 diag signal is connect to Y+ #define E2_DIAG_PIN PB12 // Driver5 diag signal is connect to Z+ #define E3_DIAG_PIN -1 // Driver6 diag signal is not connect #define E4_DIAG_PIN -1 // Driver7 diag signal is not connect // Limit Switches for endstop #define X_MIN_PIN PA14 #define X_MAX_PIN PA13 #define Y_MIN_PIN PA15 #define Y_MAX_PIN PC5 #define Z_MIN_PIN PB13 #define Z_MAX_PIN PB12 // // Steppers // Driver 0 1 2 3 4 5 6 7 // For X Y Z E0 E1 E2 E3 E4(default pin settings) // //Driver0 #define X_ENABLE_PIN PC15 #define X_STEP_PIN PC14 #define X_DIR_PIN PC13 #ifndef X_CS_PIN #define X_CS_PIN PE6 #endif //Driver1 #define Y_ENABLE_PIN PC15 #define Y_STEP_PIN PE5 #define Y_DIR_PIN PE4 #ifndef Y_CS_PIN #define Y_CS_PIN PE3 #endif //Driver2 #define Z_ENABLE_PIN PE2 #define Z_STEP_PIN PE1 #define Z_DIR_PIN PE0 #ifndef Z_CS_PIN #define Z_CS_PIN PB7 #endif //Driver3 #define E0_ENABLE_PIN PB6 #define E0_STEP_PIN PB5 #define E0_DIR_PIN PB4 #ifndef E0_CS_PIN #define E0_CS_PIN PB3 #endif //Driver4 #define E1_ENABLE_PIN PD7 #define E1_STEP_PIN PD6 #define E1_DIR_PIN PD5 #ifndef E1_CS_PIN #define E1_CS_PIN PD4 #endif //Driver5 #define E2_ENABLE_PIN PD3 #define E2_STEP_PIN PD2 #define E2_DIR_PIN PD1 #ifndef E2_CS_PIN #define E2_CS_PIN PD0 #endif //Driver6 #define E3_ENABLE_PIN PC8 #define E3_STEP_PIN PC7 #define E3_DIR_PIN PC6 #ifndef E3_CS_PIN #define E3_CS_PIN PD15 #endif //Driver7 #define E4_ENABLE_PIN PD14 #define E4_STEP_PIN PD13 #define E4_DIR_PIN PD12 #ifndef E4_CS_PIN #define E4_CS_PIN PD11 #endif // // Software SPI pins for TMC2130 stepper drivers // This board only supports SW SPI for stepper drivers // #if HAS_TMC_SPI #define TMC_USE_SW_SPI #endif #if ENABLED(TMC_USE_SW_SPI) #if !defined(TMC_SW_MOSI) || TMC_SW_MOSI == -1 #define TMC_SW_MOSI PE14 #endif #if !defined(TMC_SW_MISO) || TMC_SW_MISO == -1 #define TMC_SW_MISO PE13 #endif #if !defined(TMC_SW_SCK) || TMC_SW_SCK == -1 #define TMC_SW_SCK PE12 #endif #endif #if HAS_TMC_UART // // Software serial // No Hardware serial for steppers // #define X_SERIAL_TX_PIN PE6 #define X_SERIAL_RX_PIN PE6 #define Y_SERIAL_TX_PIN PE3 #define Y_SERIAL_RX_PIN PE3 #define Z_SERIAL_TX_PIN PB7 #define Z_SERIAL_RX_PIN PB7 #define E0_SERIAL_TX_PIN PB3 #define E0_SERIAL_RX_PIN PB3 #define E1_SERIAL_TX_PIN PD4 #define E1_SERIAL_RX_PIN PD4 #define E2_SERIAL_TX_PIN PD0 #define E2_SERIAL_RX_PIN PD0 #define E3_SERIAL_TX_PIN PD15 #define E3_SERIAL_RX_PIN PD15 #define E4_SERIAL_TX_PIN PD11 #define E4_SERIAL_RX_PIN PD11 // Reduce baud rate to improve software serial reliability #define TMC_BAUD_RATE 19200 #endif // // Temperature Sensors // #define TEMP_0_PIN PC1 // TH0 #define TEMP_1_PIN PC2 // TH1 #define TEMP_2_PIN PC3 // TH2 #define TEMP_BED_PIN PC0 // TB // // Heaters / Fans // #define HEATER_0_PIN PB1 // HE0 #define HEATER_1_PIN PB0 // HE1 #define HEATER_2_PIN PA3 // HE2 #define HEATER_BED_PIN PB10 // H-BED #define FAN_PIN PA2 // FAN0 #define FAN1_PIN PA1 // FAN1 #define FAN2_PIN PA0 // FAN2 // // Misc. Functions // #define PW_DET PC5 // Y+ #define PW_OFF PB12 // Z+ #define MT_DET_1_PIN PW_DET #define MT_DET_2_PIN PW_OFF #ifndef FIL_RUNOUT_PIN #define FIL_RUNOUT_PIN MT_DET_1_PIN #endif #ifndef FIL_RUNOUT2_PIN #define FIL_RUNOUT2_PIN MT_DET_2_PIN #endif // // Power Supply Control // #if ENABLED(MKS_PWC) #define PS_ON_PIN PW_OFF #define KILL_PIN PW_DET #define KILL_PIN_STATE HIGH #endif // Random Info #define USB_SERIAL -1 // USB Serial #ifndef SDCARD_CONNECTION #define SDCARD_CONNECTION ONBOARD #endif // // Onboard SD card // // detect pin doesn't work when ONBOARD and NO_SD_HOST_DRIVE disabled #if SD_CONNECTION_IS(ONBOARD) #define ENABLE_SPI3 #define SD_SS_PIN -1 #define SDSS PC9 #define SD_SCK_PIN PC10 #define SD_MISO_PIN PC11 #define SD_MOSI_PIN PC12 #define SD_DETECT_PIN PC4 // // LCD SD // #elif SD_CONNECTION_IS(LCD) #define ENABLE_SPI1 #define SDSS PA4 #define SD_SCK_PIN PA5 #define SD_MISO_PIN PA6 #define SD_MOSI_PIN PA7 #define SD_DETECT_PIN PB11 #endif /** * _____ _____ * (BEEPER)PB2 | · · | PE10(BTN_ENC) (SPI1 MISO) PA6 | · · | PA5 (SPI1 SCK) * (LCD_EN)PE11 | · · | PD10(LCD_RS) (BTN_EN1) PE9 | · · | PA4 (SPI1 CS) * (LCD_D4)PD9 | · · PD8(LCD_D5) (BTN_EN2) PE8 | · · PA7 (SPI1 MOSI) * (LCD_D6)PE15 | · · | PE7(LCD_D7) (SPI1_RS) PB11 | · · | RESET * GND | · · | 5V GND | · · | 3.3V * ￣￣￣ ￣￣￣ * EXP1 EXP2 */ #if ANY(TFT_COLOR_UI, TFT_CLASSIC_UI) #ifndef TOUCH_CALIBRATION_X #define TOUCH_CALIBRATION_X -17253 #endif #ifndef TOUCH_CALIBRATION_Y #define TOUCH_CALIBRATION_Y 11579 #endif #ifndef TOUCH_OFFSET_X #define TOUCH_OFFSET_X 514 #endif #ifndef TOUCH_OFFSET_Y #define TOUCH_OFFSET_Y -24 #endif #ifndef TOUCH_ORIENTATION #define TOUCH_ORIENTATION TOUCH_LANDSCAPE #endif #define TFT_CS_PIN PE15 #define TFT_SCK_PIN PA5 #define TFT_MISO_PIN PA6 #define TFT_MOSI_PIN PA7 #define TFT_DC_PIN PE7 #define TFT_RST_PIN PD10 #define TFT_A0_PIN TFT_DC_PIN #define TFT_RESET_PIN PD10 #define TFT_BACKLIGHT_PIN PE11 #define TOUCH_BUTTONS_HW_SPI #define TOUCH_BUTTONS_HW_SPI_DEVICE 1 #define LCD_BACKLIGHT_PIN PE11 #ifndef TFT_WIDTH #define TFT_WIDTH 480 #endif #ifndef TFT_HEIGHT #define TFT_HEIGHT 320 #endif #define TOUCH_CS_PIN PD9 // SPI1_NSS #define TOUCH_SCK_PIN PA5 // SPI1_SCK #define TOUCH_MISO_PIN PA6 // SPI1_MISO #define TOUCH_MOSI_PIN PA7 // SPI1_MOSI #define BTN_EN1 PE9 #define BTN_EN2 PE8 #define BEEPER_PIN PB2 #define BTN_ENC PE10 #define LCD_READ_ID 0xD3 #define LCD_USE_DMA_SPI #define TFT_BUFFER_SIZE 14400 #elif HAS_WIRED_LCD #define BEEPER_PIN PB2 #define BTN_ENC PE10 #define LCD_PINS_ENABLE PE11 #define LCD_PINS_RS PD10 #define BTN_EN1 PE9 #define BTN_EN2 PE8 #define LCD_BACKLIGHT_PIN -1 // MKS MINI12864 and MKS LCD12864B; If using MKS LCD12864A (Need to remove RPK2 resistor) #if ENABLED(MKS_MINI_12864) //#define LCD_BACKLIGHT_PIN -1 //#define LCD_RESET_PIN -1 #define DOGLCD_A0 PD11 #define DOGLCD_CS PE15 //#define DOGLCD_SCK PA5 //#define DOGLCD_MOSI PA7 #elif ENABLED(MKS_MINI_12864_V3) #define DOGLCD_CS PE11 #define DOGLCD_A0 PD10 #define LCD_PINS_DC DOGLCD_A0 #define LCD_BACKLIGHT_PIN -1 #define LCD_RESET_PIN PD9 #define NEOPIXEL_PIN PD8 #define DOGLCD_MOSI PA7 #define DOGLCD_SCK PA5 #if SD_CONNECTION_IS(ONBOARD) #define FORCE_SOFT_SPI #endif //#define LCD_SCREEN_ROT_180 #else #define LCD_PINS_D4 PD9 #if ENABLED(ULTIPANEL) #define LCD_PINS_D5 PD8 #define LCD_PINS_D6 PE15 #define LCD_PINS_D7 PE7 #endif #define BOARD_ST7920_DELAY_1 DELAY_NS(96) #define BOARD_ST7920_DELAY_2 DELAY_NS(48) #define BOARD_ST7920_DELAY_3 DELAY_NS(600) #endif // !MKS_MINI_12864 #endif // HAS_WIRED_LCD