230 lines
7 KiB
C
230 lines
7 KiB
C
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
|
|
// https://github.com/ktand/Armed
|
|
|
|
#pragma once
|
|
|
|
#if NOT_TARGET(STM32F4)
|
|
#error "Oops! Select an STM32F4 board in 'Tools > Board.'"
|
|
#elif HOTENDS > 2 || E_STEPPERS > 2
|
|
#error "Arm'ed supports up to 2 hotends / E-steppers."
|
|
#endif
|
|
|
|
#ifndef ARMED_V1_0
|
|
#define ARMED_V1_1
|
|
#endif
|
|
|
|
#undef BOARD_INFO_NAME // Defined on the command line by Arduino Core STM32
|
|
#define BOARD_INFO_NAME "Arm'ed"
|
|
#define DEFAULT_MACHINE_NAME BOARD_INFO_NAME
|
|
|
|
#define I2C_EEPROM
|
|
#define MARLIN_EEPROM_SIZE 0x1000 // 4KB
|
|
|
|
//
|
|
// Limit Switches
|
|
//
|
|
#define X_STOP_PIN PE0
|
|
#define Y_STOP_PIN PE1
|
|
#define Z_STOP_PIN PE14
|
|
|
|
//
|
|
// Z Probe (when not Z_MIN_PIN)
|
|
//
|
|
//#ifndef Z_MIN_PROBE_PIN
|
|
// #define Z_MIN_PROBE_PIN PA4
|
|
//#endif
|
|
|
|
//
|
|
// Filament Runout Sensor
|
|
//
|
|
#ifndef FIL_RUNOUT_PIN
|
|
#define FIL_RUNOUT_PIN PA3
|
|
#endif
|
|
|
|
//
|
|
// Steppers
|
|
//
|
|
|
|
#ifdef ARMED_SWAP_X_E1
|
|
#define X_STEP_PIN PE4
|
|
#define X_DIR_PIN PE2
|
|
#define X_ENABLE_PIN PE3
|
|
#define X_CS_PIN PE5
|
|
#else
|
|
#define X_STEP_PIN PD3
|
|
#define X_DIR_PIN PD2
|
|
#define X_ENABLE_PIN PD0
|
|
#define X_CS_PIN PD1
|
|
#endif
|
|
|
|
#define Y_STEP_PIN PE11
|
|
#define Y_DIR_PIN PE10
|
|
#define Y_ENABLE_PIN PE13
|
|
#define Y_CS_PIN PE12
|
|
|
|
#define Z_STEP_PIN PD6
|
|
#define Z_DIR_PIN PD7
|
|
#define Z_ENABLE_PIN PD4
|
|
#define Z_CS_PIN PD5
|
|
|
|
#define E0_STEP_PIN PB5
|
|
#define E0_DIR_PIN PB6
|
|
#ifdef ARMED_V1_1
|
|
#define E0_ENABLE_PIN PC12
|
|
#else
|
|
#define E0_ENABLE_PIN PB3
|
|
#endif
|
|
#define E0_CS_PIN PB4
|
|
|
|
#ifdef ARMED_SWAP_X_E1
|
|
#define E1_STEP_PIN PD3
|
|
#define E1_DIR_PIN PD2
|
|
#define E1_ENABLE_PIN PD0
|
|
#define E1_CS_PIN PD1
|
|
#else
|
|
#define E1_STEP_PIN PE4
|
|
#define E1_DIR_PIN PE2
|
|
#define E1_ENABLE_PIN PE3
|
|
#define E1_CS_PIN PE5
|
|
#endif
|
|
|
|
//
|
|
// Temperature Sensors
|
|
//
|
|
#define TEMP_0_PIN PC0 // Analog Input
|
|
#define TEMP_1_PIN PC1 // Analog Input
|
|
#define TEMP_BED_PIN PC2 // Analog Input
|
|
|
|
#if HOTENDS == 1 && TEMP_SENSOR_PROBE
|
|
#define TEMP_PROBE_PIN PC1
|
|
#endif
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define HEATER_0_PIN PA1 // Hardware PWM
|
|
#define HEATER_1_PIN PA2 // Hardware PWM
|
|
#define HEATER_BED_PIN PA0 // Hardware PWM
|
|
|
|
#define FAN_PIN PC6 // Hardware PWM, Part cooling fan
|
|
#define FAN1_PIN PC7 // Hardware PWM, Extruder fan
|
|
#define FAN2_PIN PC8 // Hardware PWM, Controller fan
|
|
|
|
//
|
|
// Misc functions
|
|
//
|
|
#define SDSS PE7
|
|
#define LED_PIN PB7 // Heart beat
|
|
#define PS_ON_PIN PA10
|
|
#define KILL_PIN PA8
|
|
#define PWR_LOSS PA4 // Power loss / nAC_FAULT
|
|
|
|
//
|
|
// LCD / Controller
|
|
//
|
|
#define SD_DETECT_PIN PA15
|
|
#define BEEPER_PIN PC9
|
|
|
|
#if ENABLED(FYSETC_MINI_12864)
|
|
//
|
|
// See https://wiki.fysetc.com/Mini12864_Panel/?fbclid=IwAR1FyjuNdVOOy9_xzky3qqo_WeM5h-4gpRnnWhQr_O1Ef3h0AFnFXmCehK8
|
|
//
|
|
#define DOGLCD_A0 PE9
|
|
#define DOGLCD_CS PE8
|
|
|
|
#define LCD_BACKLIGHT_PIN -1
|
|
|
|
#define LCD_RESET_PIN PB12 // Must be high or open for LCD to operate normally.
|
|
|
|
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
|
|
#ifndef RGB_LED_R_PIN
|
|
#define RGB_LED_R_PIN PB13
|
|
#endif
|
|
#ifndef RGB_LED_G_PIN
|
|
#define RGB_LED_G_PIN PB14
|
|
#endif
|
|
#ifndef RGB_LED_B_PIN
|
|
#define RGB_LED_B_PIN PB15
|
|
#endif
|
|
#elif ENABLED(FYSETC_MINI_12864_2_1)
|
|
#define NEOPIXEL_PIN PB13
|
|
#endif
|
|
#else
|
|
#define LCD_PINS_RS PE9
|
|
#define LCD_PINS_ENABLE PE8
|
|
#define LCD_PINS_D4 PB12
|
|
#define LCD_PINS_D5 PB13
|
|
#define LCD_PINS_D6 PB14
|
|
#define LCD_PINS_D7 PB15
|
|
|
|
#if ENABLED(MKS_MINI_12864)
|
|
#define DOGLCD_CS PB13
|
|
#define DOGLCD_A0 PB14
|
|
#endif
|
|
#endif
|
|
|
|
#define BTN_EN1 PC4
|
|
#define BTN_EN2 PC5
|
|
#define BTN_ENC PC3
|
|
|
|
//
|
|
// Extension pins
|
|
//
|
|
#define EXT0_PIN PB0
|
|
#define EXT1_PIN PB1
|
|
#define EXT2_PIN PB2
|
|
#define EXT3_PIN PD8
|
|
#define EXT4_PIN PD9
|
|
#define EXT5_PIN PD10
|
|
#define EXT6_PIN PD11
|
|
#define EXT7_PIN PD12
|
|
#define EXT8_PIN PB10
|
|
#define EXT9_PIN PB11
|
|
|
|
#if HAS_TMC_UART
|
|
// TMC2208/TMC2209 stepper drivers
|
|
//
|
|
// Software serial
|
|
//
|
|
#define X_SERIAL_TX_PIN EXT0_PIN
|
|
#define X_SERIAL_RX_PIN EXT0_PIN
|
|
|
|
#define Y_SERIAL_TX_PIN EXT1_PIN
|
|
#define Y_SERIAL_RX_PIN EXT1_PIN
|
|
|
|
#define Z_SERIAL_TX_PIN EXT2_PIN
|
|
#define Z_SERIAL_RX_PIN EXT2_PIN
|
|
|
|
#define E0_SERIAL_TX_PIN EXT3_PIN
|
|
#define E0_SERIAL_RX_PIN EXT3_PIN
|
|
|
|
#define E1_SERIAL_RX_PIN EXT4_PIN
|
|
#define E1_SERIAL_TX_PIN EXT4_PIN
|
|
|
|
#define Z2_SERIAL_RX_PIN EXT4_PIN
|
|
#define Z2_SERIAL_TX_PIN EXT4_PIN
|
|
|
|
#define TMC_BAUD_RATE 19200
|
|
#endif
|