183 lines
5.3 KiB
C
183 lines
5.3 KiB
C
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
#pragma once
|
|
|
|
/**
|
|
* TH3D EZBoard pin assignments
|
|
*/
|
|
|
|
#if NOT_TARGET(MCU_LPC1769)
|
|
#error "Oops! Make sure you have the LPC1769 environment selected in your IDE."
|
|
#endif
|
|
|
|
#define BOARD_INFO_NAME "TH3D EZBoard"
|
|
#define BOARD_WEBSITE_URL "th3dstudio.com"
|
|
|
|
//
|
|
// Servos
|
|
//
|
|
#define SERVO0_PIN P2_04
|
|
|
|
//
|
|
// Limit Switches
|
|
//
|
|
#define X_STOP_PIN P1_24
|
|
#define Y_STOP_PIN P1_25
|
|
#define Z_STOP_PIN P1_26
|
|
|
|
//
|
|
// Filament Runout Sensor
|
|
//
|
|
#ifndef FIL_RUNOUT_PIN
|
|
#define FIL_RUNOUT_PIN P1_27
|
|
#endif
|
|
|
|
//
|
|
// Steppers
|
|
//
|
|
#define X_STEP_PIN P2_00
|
|
#define X_DIR_PIN P1_16
|
|
#define X_ENABLE_PIN P1_17
|
|
|
|
#define Y_STEP_PIN P2_01
|
|
#define Y_DIR_PIN P1_10
|
|
#define Y_ENABLE_PIN P1_09
|
|
|
|
#define Z_STEP_PIN P2_02
|
|
#define Z_DIR_PIN P1_15
|
|
#define Z_ENABLE_PIN P1_14
|
|
|
|
#define E0_STEP_PIN P2_03
|
|
#define E0_DIR_PIN P1_04
|
|
#define E0_ENABLE_PIN P1_08
|
|
|
|
#define E1_STEP_PIN P2_08
|
|
#define E1_DIR_PIN P2_13
|
|
#define E1_ENABLE_PIN P4_29
|
|
|
|
#if HAS_TMC_UART
|
|
//
|
|
// TMC220x stepper drivers
|
|
// Software serial
|
|
//
|
|
#define X_SERIAL_TX_PIN P0_04
|
|
#define X_SERIAL_RX_PIN P0_05
|
|
#define Y_SERIAL_TX_PIN P0_10
|
|
#define Y_SERIAL_RX_PIN P0_11
|
|
#define Z_SERIAL_TX_PIN P0_19
|
|
#define Z_SERIAL_RX_PIN P0_20
|
|
#define E0_SERIAL_TX_PIN P0_22
|
|
#define E0_SERIAL_RX_PIN P0_21
|
|
|
|
// Reduce baud rate to improve software serial reliability
|
|
#define TMC_BAUD_RATE 19200
|
|
#endif
|
|
|
|
//
|
|
// Temp Sensors
|
|
// 3.3V max when defined as an Analog Input!
|
|
//
|
|
#if TEMP_SENSOR_0 == 20 // PT100 Adapter
|
|
#define TEMP_0_PIN P0_02_A7 // Analog Input
|
|
#else
|
|
#define TEMP_0_PIN P0_23_A0 // Analog Input P0_23
|
|
#endif
|
|
|
|
#define TEMP_BED_PIN P0_24_A1 // Analog Input P0_24
|
|
#define TEMP_1_PIN P0_25_A2 // Analog Input P0_25
|
|
|
|
#if ENABLED(FILAMENT_WIDTH_SENSOR)
|
|
#define FILWIDTH_PIN P0_26_A3 // Analog Input P0_26
|
|
#else
|
|
#define TEMP_2_PIN P0_26_A3 // Analog Input P0_26
|
|
#endif
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define HEATER_BED_PIN P2_05
|
|
#define HEATER_0_PIN P2_07
|
|
#ifndef FAN_PIN
|
|
#define FAN_PIN P2_06
|
|
#endif
|
|
#define FAN1_PIN P1_22
|
|
|
|
//
|
|
// Auto fans
|
|
//
|
|
#define AUTO_FAN_PIN P1_22 // FET 3
|
|
#ifndef E0_AUTO_FAN_PIN
|
|
#define E0_AUTO_FAN_PIN AUTO_FAN_PIN
|
|
#endif
|
|
#ifndef E1_AUTO_FAN_PIN
|
|
#define E1_AUTO_FAN_PIN AUTO_FAN_PIN
|
|
#endif
|
|
#ifndef E2_AUTO_FAN_PIN
|
|
#define E2_AUTO_FAN_PIN AUTO_FAN_PIN
|
|
#endif
|
|
|
|
//
|
|
// SD Card
|
|
//
|
|
|
|
#define SDCARD_CONNECTION ONBOARD
|
|
|
|
#define SCK_PIN P0_07
|
|
#define MISO_PIN P0_08
|
|
#define MOSI_PIN P0_09
|
|
#define ONBOARD_SD_CS_PIN P0_06
|
|
#define SS_PIN ONBOARD_SD_CS_PIN
|
|
|
|
//
|
|
// LCD / Controller
|
|
//
|
|
|
|
/**
|
|
* _____
|
|
* 5V | · · | GND
|
|
* (LCD_EN) P0_18 | · · | P0_16 (LCD_RS)
|
|
* (LCD_D4) P0_15 | · · | P3_25 (BTN_EN2)
|
|
* (RESET) P2_11 | · · | P3_26 (BTN_EN1)
|
|
* (BTN_ENC) P1_30 | · · | P1_31 (BEEPER)
|
|
* -----
|
|
* EXP1
|
|
*
|
|
* LCD_PINS_D5, D6, and D7 are not present in the EXP1 connector, and will need to be
|
|
* defined to use the REPRAP_DISCOUNT_SMART_CONTROLLER.
|
|
*
|
|
* A remote SD card is currently not supported because the pins routed to the EXP2
|
|
* connector are shared with the onboard SD card.
|
|
*/
|
|
|
|
#if ENABLED(CR10_STOCKDISPLAY)
|
|
#define BEEPER_PIN P1_31
|
|
#define BTN_EN1 P3_26
|
|
#define BTN_EN2 P3_25
|
|
#define BTN_ENC P1_30
|
|
#define LCD_PINS_RS P0_16
|
|
#define LCD_PINS_ENABLE P0_18
|
|
#define LCD_PINS_D4 P0_15
|
|
#define KILL_PIN P2_11
|
|
#elif HAS_WIRED_LCD
|
|
#error "Only the CR10_STOCKDISPLAY is supported with TH3D EZBoard."
|
|
#endif
|