131 lines
4.2 KiB
C
131 lines
4.2 KiB
C
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
#pragma once
|
|
|
|
/**
|
|
* ╦╔═╗╔═╗┬ ┬┬─┐┌─┐┬─┐┌─┐╔═╗┌─┐┬─┐┬ ┬┌┬┐ ┌─┐┌─┐┌┬┐
|
|
* ║║ ╦╠═╣│ │├┬┘│ │├┬┘├─┤╠╣ │ │├┬┘│ ││││ │ │ ││││
|
|
* ╚╝╚═╝╩ ╩└─┘┴└─└─┘┴└─┴ ┴╚ └─┘┴└─└─┘┴ ┴o└─┘└─┘┴ ┴
|
|
* Pin assignments for 32-bit JGAurora A5S & A1
|
|
*/
|
|
|
|
#ifndef __STM32F1__
|
|
#error "Oops! Select an STM32F1 board in 'Tools > Board.'"
|
|
#elif HOTENDS > 1 || E_STEPPERS > 1
|
|
#error "JGAurora 32-bit board only supports 1 hotend / E-stepper. Comment out this line to continue."
|
|
#endif
|
|
#define BOARD_INFO_NAME "JGAurora A5S A1 board"
|
|
|
|
#ifndef STM32_XL_DENSITY
|
|
#define STM32_XL_DENSITY
|
|
#endif
|
|
|
|
// #define MCU_STM32F103ZE // not yet required
|
|
// Enable EEPROM Emulation for this board, so that we don't overwrite factory data
|
|
|
|
//#define I2C_EEPROM // AT24C64
|
|
//#define E2END 0x7FFF // 64KB
|
|
//#define FLASH_EEPROM_EMULATION
|
|
//#define E2END 0xFFF // 4KB
|
|
//#define E2END uint32(EEPROM_START_ADDRESS + (EEPROM_PAGE_SIZE * 2) - 1)
|
|
//#define EEPROM_CHITCHAT
|
|
//#define DEBUG_EEPROM_READWRITE
|
|
|
|
//
|
|
// Limit Switches
|
|
//
|
|
#define X_STOP_PIN PC6
|
|
#define Y_STOP_PIN PG8
|
|
#define Z_STOP_PIN PG7
|
|
//#define X_MAX_PIN PC5
|
|
//#define Y_MAX_PIN PC4
|
|
//#define Z_MAX_PIN PB0
|
|
|
|
//
|
|
// Steppers
|
|
//
|
|
#define X_STEP_PIN PD6
|
|
#define X_DIR_PIN PD3
|
|
#define X_ENABLE_PIN PG9
|
|
|
|
#define Y_STEP_PIN PG12
|
|
#define Y_DIR_PIN PG11
|
|
#define Y_ENABLE_PIN PG13
|
|
|
|
#define Z_STEP_PIN PG15
|
|
#define Z_DIR_PIN PG14
|
|
#define Z_ENABLE_PIN PB8
|
|
|
|
#define E0_STEP_PIN PE2
|
|
#define E0_DIR_PIN PB9
|
|
#define E0_ENABLE_PIN PE3
|
|
|
|
#define E1_STEP_PIN PE5
|
|
#define E1_DIR_PIN PE4
|
|
#define E1_ENABLE_PIN PE6
|
|
|
|
//
|
|
// Temperature Sensors
|
|
//
|
|
#define TEMP_0_PIN PC2
|
|
#define TEMP_BED_PIN PC1
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define HEATER_0_PIN PA2
|
|
#define HEATER_BED_PIN PA3
|
|
|
|
#define FAN_PIN PA1
|
|
|
|
#define FIL_RUNOUT_PIN PC7
|
|
|
|
//
|
|
// LCD
|
|
//
|
|
#define LCD_BACKLIGHT_PIN PF11
|
|
#define FSMC_CS_PIN PD7
|
|
#define FSMC_RS_PIN PG0
|
|
|
|
#define LCD_USE_DMA_FSMC // Use DMA transfers to send data to the TFT
|
|
#define FSMC_DMA_DEV DMA2
|
|
#define FSMC_DMA_CHANNEL DMA_CH5
|
|
|
|
//
|
|
// SD Card
|
|
//
|
|
#define SD_DETECT_PIN PF10
|
|
|
|
//
|
|
// Misc.
|
|
//
|
|
#define BEEPER_PIN PC3 // use PB7 to shut up if desired
|
|
#define LED_PIN PC13
|
|
|
|
//
|
|
// Touch support
|
|
//
|
|
#if ENABLED(TOUCH_BUTTONS)
|
|
#define TOUCH_CS_PIN PA4
|
|
#define TOUCH_INT_PIN PC4
|
|
#endif
|