173 lines
4.7 KiB
C
173 lines
4.7 KiB
C
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
#pragma once
|
|
|
|
#ifndef __STM32F1__
|
|
#error "Oops! Select an STM32F1 board in 'Tools > Board.'"
|
|
#endif
|
|
|
|
#define BOARD_INFO_NAME "FLY_MINI"
|
|
#define BOARD_WEBSITE_URL "github.com/FLYmaker"
|
|
#define DISABLE_JTAG
|
|
|
|
//
|
|
// Flash EEPROM Emulation
|
|
//
|
|
#define FLASH_EEPROM_EMULATION
|
|
#define EEPROM_PAGE_SIZE 0x800 // 2KB
|
|
#define EEPROM_START_ADDRESS (0x8000000 + 256 * 1024 - 2 * EEPROM_PAGE_SIZE) // 256K firmware space
|
|
#define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE
|
|
|
|
//
|
|
// Servos
|
|
//
|
|
#define SERVO0_PIN PA8
|
|
|
|
//
|
|
// Limit Switches
|
|
//
|
|
#define X_MIN_PIN PC12
|
|
#define X_MAX_PIN PC11
|
|
#define Y_MIN_PIN PC10
|
|
#define Y_MAX_PIN PA15
|
|
#define Z_MIN_PIN PA14
|
|
#define Z_MAX_PIN PA13
|
|
|
|
//
|
|
// Steppers
|
|
//
|
|
#define X_STEP_PIN PB1
|
|
#define X_DIR_PIN PB2
|
|
#define X_ENABLE_PIN PB10
|
|
#ifndef X_CS_PIN
|
|
#define X_CS_PIN PB0
|
|
#endif
|
|
|
|
#define Y_STEP_PIN PA2
|
|
#define Y_DIR_PIN PC4
|
|
#define Y_ENABLE_PIN PC5
|
|
#ifndef Y_CS_PIN
|
|
#define Y_CS_PIN PA7
|
|
#endif
|
|
|
|
#define Z_STEP_PIN PA3
|
|
#define Z_DIR_PIN PA5
|
|
#define Z_ENABLE_PIN PA6
|
|
#ifndef Z_CS_PIN
|
|
#define Z_CS_PIN PA4
|
|
#endif
|
|
|
|
#define E0_STEP_PIN PA1
|
|
#define E0_DIR_PIN PC3
|
|
#define E0_ENABLE_PIN PA0
|
|
#ifndef E0_CS_PIN
|
|
#define E0_CS_PIN PC2
|
|
#endif
|
|
|
|
#if ENABLED(TMC_USE_SW_SPI)
|
|
#ifndef TMC_SW_MOSI
|
|
#define TMC_SW_MOSI PB15
|
|
#endif
|
|
#ifndef TMC_SW_MISO
|
|
#define TMC_SW_MISO PB14
|
|
#endif
|
|
#ifndef TMC_SW_SCK
|
|
#define TMC_SW_SCK PB13
|
|
#endif
|
|
#endif
|
|
|
|
#if HAS_TMC_UART
|
|
//
|
|
// Software serial
|
|
//
|
|
#define X_SERIAL_TX_PIN PB0
|
|
#define X_SERIAL_RX_PIN PB0
|
|
#define Y_SERIAL_TX_PIN PA7
|
|
#define Y_SERIAL_RX_PIN PA7
|
|
#define Z_SERIAL_TX_PIN PA4
|
|
#define Z_SERIAL_RX_PIN PA4
|
|
#define E0_SERIAL_TX_PIN PC2
|
|
#define E0_SERIAL_RX_PIN PC2
|
|
#endif
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define HEATER_0_PIN PC6
|
|
#define HEATER_BED_PIN PC7
|
|
#ifndef FAN_PIN
|
|
#define FAN_PIN PC8
|
|
#endif
|
|
#define FAN1_PIN PC9
|
|
|
|
//
|
|
// Temperature Sensors
|
|
//
|
|
#define TEMP_BED_PIN PC0 // Analog Input
|
|
#define TEMP_0_PIN PC1 // Analog Input
|
|
|
|
//
|
|
// LCD Pins
|
|
//
|
|
|
|
//
|
|
// LCD / Controller
|
|
//
|
|
#define ENABLE_SPI2
|
|
#define SS_PIN PB12
|
|
#define SCK_PIN PB13
|
|
#define MISO_PIN PB14
|
|
#define MOSI_PIN PB15
|
|
|
|
#define SDSS SS_PIN
|
|
#define SD_DETECT_PIN PB11
|
|
|
|
#define BEEPER_PIN PC14
|
|
|
|
#define LCD_PINS_RS PB8
|
|
#define LCD_PINS_ENABLE PB9
|
|
#define LCD_PINS_D4 PB7
|
|
#define LCD_PINS_D5 PB6
|
|
#define LCD_PINS_D6 PB5
|
|
#define LCD_PINS_D7 PB4
|
|
|
|
#define BTN_EN1 PD2
|
|
#define BTN_EN2 PB3
|
|
#define BTN_ENC PC13
|
|
|
|
//
|
|
// Filament runout
|
|
//
|
|
|
|
//
|
|
// ST7920 Delays
|
|
//
|
|
#ifndef ST7920_DELAY_1
|
|
#define ST7920_DELAY_1 DELAY_NS(96)
|
|
#endif
|
|
#ifndef ST7920_DELAY_2
|
|
#define ST7920_DELAY_2 DELAY_NS(48)
|
|
#endif
|
|
#ifndef ST7920_DELAY_3
|
|
#define ST7920_DELAY_3 DELAY_NS(715)
|
|
#endif
|