c6caa45ae2
fixes #246 Added statements to set the limit switch positions to the maximum travel if homing in the positive direction as well as bed center at (0,0) if defined. Relocated code based on feedback.
299 lines
12 KiB
C
299 lines
12 KiB
C
#ifndef CONFIGURATION_H
|
|
#define CONFIGURATION_H
|
|
|
|
// This configurtion file contains the basic settings.
|
|
// Advanced settings can be found in Configuration_adv.h
|
|
// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
|
|
|
|
//User specified version info of THIS file to display in [Pronterface, etc] terminal window during startup.
|
|
//Implementation of an idea by Prof Braino to inform user that any changes made
|
|
//to THIS file by the user have been successfully uploaded into firmware.
|
|
#define STRING_VERSION_CONFIG_H "2012-05-02" //Personal revision number for changes to THIS file.
|
|
#define STRING_CONFIG_H_AUTHOR "erik" //Who made the changes.
|
|
|
|
// This determines the communication speed of the printer
|
|
#define BAUDRATE 250000
|
|
//#define BAUDRATE 115200
|
|
|
|
//// The following define selects which electronics board you have. Please choose the one that matches your setup
|
|
// Gen7 custom (Alfons3 Version) = 10 "https://github.com/Alfons3/Generation_7_Electronics"
|
|
// Gen7 v1.1, v1.2 = 11
|
|
// Gen7 v1.3 = 12
|
|
// Gen7 v1.4 = 13
|
|
// MEGA/RAMPS up to 1.2 = 3
|
|
// RAMPS 1.3 = 33 (Power outputs: Extruder, Bed, Fan)
|
|
// RAMPS 1.3 = 34 (Power outputs: Extruder0, Extruder1, Bed)
|
|
// Gen6 = 5
|
|
// Gen6 deluxe = 51
|
|
// Sanguinololu 1.2 and above = 62
|
|
// Melzi = 63
|
|
// Ultimaker = 7
|
|
// Teensylu = 8
|
|
// Gen3+ =9
|
|
|
|
#ifndef MOTHERBOARD
|
|
#define MOTHERBOARD 7
|
|
#endif
|
|
|
|
|
|
|
|
//===========================================================================
|
|
//=============================Thermal Settings ============================
|
|
//===========================================================================
|
|
//
|
|
//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
|
|
//
|
|
//// Temperature sensor settings:
|
|
// -2 is thermocouple with MAX6675 (only for sensor 0)
|
|
// -1 is thermocouple with AD595
|
|
// 0 is not used
|
|
// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
|
|
// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
|
|
// 3 is mendel-parts thermistor (4.7k pullup)
|
|
// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
|
|
// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan) (4.7k pullup)
|
|
// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
|
|
// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
|
|
//
|
|
// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
|
|
// (but gives greater accuracy and more stable PID)
|
|
// 51 is 100k thermistor - EPCOS (1k pullup)
|
|
// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
|
|
// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan) (1k pullup)
|
|
|
|
#define TEMP_SENSOR_0 -1
|
|
#define TEMP_SENSOR_1 0
|
|
#define TEMP_SENSOR_2 0
|
|
#define TEMP_SENSOR_BED 0
|
|
|
|
// Actual temperature must be close to target for this long before M109 returns success
|
|
#define TEMP_RESIDENCY_TIME 10 // (seconds)
|
|
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
|
|
#define TEMP_WINDOW 1 // (degC) Window around target to start the recidency timer x degC early.
|
|
|
|
// The minimal temperature defines the temperature below which the heater will not be enabled It is used
|
|
// to check that the wiring to the thermistor is not broken.
|
|
// Otherwise this would lead to the heater being powered on all the time.
|
|
#define HEATER_0_MINTEMP 5
|
|
#define HEATER_1_MINTEMP 5
|
|
#define HEATER_2_MINTEMP 5
|
|
#define BED_MINTEMP 5
|
|
|
|
// When temperature exceeds max temp, your heater will be switched off.
|
|
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
|
|
// You should use MINTEMP for thermistor short/failure protection.
|
|
#define HEATER_0_MAXTEMP 275
|
|
#define HEATER_1_MAXTEMP 275
|
|
#define HEATER_2_MAXTEMP 275
|
|
#define BED_MAXTEMP 150
|
|
|
|
// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the
|
|
// average current. The value should be an integer and the heat bed will be turned on for 1 interval of
|
|
// HEATER_BED_DUTY_CYCLE_DIVIDER intervals.
|
|
//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4
|
|
|
|
// PID settings:
|
|
// Comment the following line to disable PID and enable bang-bang.
|
|
#define PIDTEMP
|
|
#define PID_MAX 255 // limits current to nozzle; 255=full current
|
|
#ifdef PIDTEMP
|
|
//#define PID_DEBUG // Sends debug data to the serial port.
|
|
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104 sets the output power in %
|
|
#define PID_INTEGRAL_DRIVE_MAX 255 //limit for the integral term
|
|
#define K1 0.95 //smoothing factor withing the PID
|
|
#define PID_dT ((16.0 * 8.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the
|
|
|
|
// If you are using a preconfigured hotend then you can use one of the value sets by uncommenting it
|
|
// Ultimaker
|
|
#define DEFAULT_Kp 22.2
|
|
#define DEFAULT_Ki 1.08
|
|
#define DEFAULT_Kd 114
|
|
|
|
// Makergear
|
|
// #define DEFAULT_Kp 7.0
|
|
// #define DEFAULT_Ki 0.1
|
|
// #define DEFAULT_Kd 12
|
|
|
|
// Mendel Parts V9 on 12V
|
|
// #define DEFAULT_Kp 63.0
|
|
// #define DEFAULT_Ki 2.25
|
|
// #define DEFAULT_Kd 440
|
|
#endif // PIDTEMP
|
|
|
|
//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
|
|
//can be software-disabled for whatever purposes by
|
|
#define PREVENT_DANGEROUS_EXTRUDE
|
|
//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
|
|
#define PREVENT_LENGTHY_EXTRUDE
|
|
|
|
#define EXTRUDE_MINTEMP 170
|
|
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
|
|
|
|
//===========================================================================
|
|
//=============================Mechanical Settings===========================
|
|
//===========================================================================
|
|
|
|
// Uncomment the following line to enable CoreXY kinematics
|
|
// #define COREXY
|
|
|
|
// corse Endstop Settings
|
|
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
|
|
|
#ifndef ENDSTOPPULLUPS
|
|
// fine Enstop settings: Individual Pullups. will be ignord if ENDSTOPPULLUPS is defined
|
|
#define ENDSTOPPULLUP_XMAX
|
|
#define ENDSTOPPULLUP_YMAX
|
|
#define ENDSTOPPULLUP_ZMAX
|
|
#define ENDSTOPPULLUP_XMIN
|
|
#define ENDSTOPPULLUP_YMIN
|
|
//#define ENDSTOPPULLUP_ZMIN
|
|
#endif
|
|
|
|
#ifdef ENDSTOPPULLUPS
|
|
#define ENDSTOPPULLUP_XMAX
|
|
#define ENDSTOPPULLUP_YMAX
|
|
#define ENDSTOPPULLUP_ZMAX
|
|
#define ENDSTOPPULLUP_XMIN
|
|
#define ENDSTOPPULLUP_YMIN
|
|
#define ENDSTOPPULLUP_ZMIN
|
|
#endif
|
|
|
|
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
|
|
const bool X_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
|
|
const bool Y_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
|
|
const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
|
|
//#define DISABLE_MAX_ENDSTOPS
|
|
|
|
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
|
#define X_ENABLE_ON 0
|
|
#define Y_ENABLE_ON 0
|
|
#define Z_ENABLE_ON 0
|
|
#define E_ENABLE_ON 0 // For all extruders
|
|
|
|
// Disables axis when it's not being used.
|
|
#define DISABLE_X false
|
|
#define DISABLE_Y false
|
|
#define DISABLE_Z false
|
|
#define DISABLE_E false // For all extruders
|
|
|
|
#define INVERT_X_DIR true // for Mendel set to false, for Orca set to true
|
|
#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false
|
|
#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true
|
|
#define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
|
#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
|
#define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
|
|
|
// ENDSTOP SETTINGS:
|
|
// Sets direction of endstops when homing; 1=MAX, -1=MIN
|
|
#define X_HOME_DIR -1
|
|
#define Y_HOME_DIR -1
|
|
#define Z_HOME_DIR -1
|
|
|
|
#define min_software_endstops true //If true, axis won't move to coordinates less than HOME_POS.
|
|
#define max_software_endstops true //If true, axis won't move to coordinates greater than the defined lengths below.
|
|
// Travel limits after homing
|
|
#define X_MAX_POS 205
|
|
#define X_MIN_POS 0
|
|
#define Y_MAX_POS 205
|
|
#define Y_MIN_POS 0
|
|
#define Z_MAX_POS 200
|
|
#define Z_MIN_POS 0
|
|
|
|
#define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
|
|
#define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
|
|
#define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
|
|
|
|
// The position of the homing switches
|
|
//#define MANUAL_HOME_POSITIONS // If defined, manualy programed locations will be used
|
|
//#define BED_CENTER_AT_0_0 // If defined the center of the bed is defined as (0,0)
|
|
|
|
//Manual homing switch locations:
|
|
#define MANUAL_X_HOME_POS 0
|
|
#define MANUAL_Y_HOME_POS 0
|
|
#define MANUAL_Z_HOME_POS 0
|
|
|
|
//// MOVEMENT SETTINGS
|
|
#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
|
|
#define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0} // set the homing speeds (mm/min)
|
|
|
|
// default settings
|
|
|
|
#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200*8/3,760*1.1} // default steps per unit for ultimaker
|
|
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 45} // (mm/sec)
|
|
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
|
|
|
|
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
|
#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts
|
|
|
|
//
|
|
#define DEFAULT_XYJERK 20.0 // (mm/sec)
|
|
#define DEFAULT_ZJERK 0.4 // (mm/sec)
|
|
#define DEFAULT_EJERK 5.0 // (mm/sec)
|
|
|
|
//===========================================================================
|
|
//=============================Additional Features===========================
|
|
//===========================================================================
|
|
|
|
// EEPROM
|
|
// the microcontroller can store settings in the EEPROM, e.g. max velocity...
|
|
// M500 - stores paramters in EEPROM
|
|
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
|
|
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
|
|
//define this to enable eeprom support
|
|
//#define EEPROM_SETTINGS
|
|
//to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
|
|
// please keep turned on if you can.
|
|
//#define EEPROM_CHITCHAT
|
|
|
|
//LCD and SD support
|
|
//#define ULTRA_LCD //general lcd support, also 16x2
|
|
//#define SDSUPPORT // Enable SD Card Support in Hardware Console
|
|
|
|
//#define ULTIMAKERCONTROLLER //as available from the ultimaker online store.
|
|
//#define ULTIPANEL //the ultipanel as on thingiverse
|
|
|
|
|
|
#ifdef ULTIMAKERCONTROLLER //automatic expansion
|
|
#define ULTIPANEL
|
|
#define NEWPANEL
|
|
#endif
|
|
|
|
|
|
#ifdef ULTIPANEL
|
|
// #define NEWPANEL //enable this if you have a click-encoder panel
|
|
#define SDSUPPORT
|
|
#define ULTRA_LCD
|
|
#define LCD_WIDTH 20
|
|
#define LCD_HEIGHT 4
|
|
|
|
// Preheat Constants
|
|
#define PLA_PREHEAT_HOTEND_TEMP 180
|
|
#define PLA_PREHEAT_HPB_TEMP 70
|
|
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
|
|
|
|
#define ABS_PREHEAT_HOTEND_TEMP 240
|
|
#define ABS_PREHEAT_HPB_TEMP 100
|
|
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
|
|
|
|
#else //no panel but just lcd
|
|
#ifdef ULTRA_LCD
|
|
#define LCD_WIDTH 16
|
|
#define LCD_HEIGHT 2
|
|
#endif
|
|
#endif
|
|
|
|
// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino
|
|
//#define FAST_PWM_FAN
|
|
|
|
// M240 Triggers a camera by emulating a Canon RC-1 Remote
|
|
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
|
|
// #define PHOTOGRAPH_PIN 23
|
|
|
|
// SF send wrong arc g-codes when using Arc Point as fillet procedure
|
|
//#define SF_ARC_FIX
|
|
|
|
#include "Configuration_adv.h"
|
|
#include "thermistortables.h"
|
|
|
|
#endif //__CONFIGURATION_H
|