496 lines
15 KiB
C
496 lines
15 KiB
C
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
#pragma once
|
|
|
|
#include "env_validate.h"
|
|
|
|
#define BOARD_INFO_NAME "BTT SKR V2.0"
|
|
|
|
// Use one of these or SDCard-based Emulation will be used
|
|
#if NO_EEPROM_SELECTED
|
|
//#define SRAM_EEPROM_EMULATION // Use BackSRAM-based EEPROM emulation
|
|
#define FLASH_EEPROM_EMULATION // Use Flash-based EEPROM emulation
|
|
#endif
|
|
|
|
#if ENABLED(FLASH_EEPROM_EMULATION)
|
|
// Decrease delays and flash wear by spreading writes across the
|
|
// 128 kB sector allocated for EEPROM emulation.
|
|
#define FLASH_EEPROM_LEVELING
|
|
#endif
|
|
|
|
// USB Flash Drive support
|
|
#define HAS_OTG_USB_HOST_SUPPORT
|
|
|
|
// Avoid conflict with TIMER_TONE
|
|
#define STEP_TIMER 10
|
|
|
|
//
|
|
// Servos
|
|
//
|
|
#define SERVO0_PIN PE5
|
|
|
|
//
|
|
// Trinamic Stallguard pins
|
|
//
|
|
#define X_DIAG_PIN PC1 // X-STOP
|
|
#define Y_DIAG_PIN PC3 // Y-STOP
|
|
#define Z_DIAG_PIN PC0 // Z-STOP
|
|
#define E0_DIAG_PIN PC2 // E0DET
|
|
#define E1_DIAG_PIN PA0 // E1DET
|
|
|
|
//
|
|
// Limit Switches
|
|
//
|
|
#ifdef X_STALL_SENSITIVITY
|
|
#define X_STOP_PIN X_DIAG_PIN
|
|
#if X_HOME_DIR < 0
|
|
#define X_MAX_PIN PC2 // E0DET
|
|
#else
|
|
#define X_MIN_PIN PC2 // E0DET
|
|
#endif
|
|
#elif ENABLED(X_DUAL_ENDSTOPS)
|
|
#ifndef X_MIN_PIN
|
|
#define X_MIN_PIN PC1 // X-STOP
|
|
#endif
|
|
#ifndef X_MAX_PIN
|
|
#define X_MAX_PIN PC2 // E0DET
|
|
#endif
|
|
#else
|
|
#define X_STOP_PIN PC1 // X-STOP
|
|
#endif
|
|
|
|
#ifdef Y_STALL_SENSITIVITY
|
|
#define Y_STOP_PIN Y_DIAG_PIN
|
|
#if Y_HOME_DIR < 0
|
|
#define Y_MAX_PIN PA0 // E1DET
|
|
#else
|
|
#define Y_MIN_PIN PA0 // E1DET
|
|
#endif
|
|
#elif ENABLED(Y_DUAL_ENDSTOPS)
|
|
#ifndef Y_MIN_PIN
|
|
#define Y_MIN_PIN PC3 // Y-STOP
|
|
#endif
|
|
#ifndef Y_MAX_PIN
|
|
#define Y_MAX_PIN PA0 // E1DET
|
|
#endif
|
|
#else
|
|
#define Y_STOP_PIN PC3 // Y-STOP
|
|
#endif
|
|
|
|
#ifdef Z_STALL_SENSITIVITY
|
|
#define Z_STOP_PIN Z_DIAG_PIN
|
|
#if Z_HOME_DIR < 0
|
|
#define Z_MAX_PIN PC15 // PWRDET
|
|
#else
|
|
#define Z_MIN_PIN PC15 // PWRDET
|
|
#endif
|
|
#elif ENABLED(Z_MULTI_ENDSTOPS)
|
|
#ifndef Z_MIN_PIN
|
|
#define Z_MIN_PIN PC0 // Z-STOP
|
|
#endif
|
|
#ifndef Z_MAX_PIN
|
|
#define Z_MAX_PIN PC15 // PWRDET
|
|
#endif
|
|
#else
|
|
#ifndef Z_STOP_PIN
|
|
#define Z_STOP_PIN PC0 // Z-STOP
|
|
#endif
|
|
#endif
|
|
|
|
//
|
|
// Z Probe (when not Z_MIN_PIN)
|
|
//
|
|
#ifndef Z_MIN_PROBE_PIN
|
|
#define Z_MIN_PROBE_PIN PE4
|
|
#endif
|
|
|
|
//
|
|
// Filament Runout Sensor
|
|
//
|
|
#define FIL_RUNOUT_PIN PC2 // E0DET
|
|
#define FIL_RUNOUT2_PIN PA0 // E1DET
|
|
|
|
//
|
|
// Power Supply Control
|
|
//
|
|
#ifndef PS_ON_PIN
|
|
#define PS_ON_PIN PE8 // PS-ON
|
|
#endif
|
|
|
|
//
|
|
// Power Loss Detection
|
|
//
|
|
#ifndef POWER_LOSS_PIN
|
|
#define POWER_LOSS_PIN PC15 // PWRDET
|
|
#endif
|
|
|
|
//
|
|
// NeoPixel LED
|
|
//
|
|
#ifndef NEOPIXEL_PIN
|
|
#define NEOPIXEL_PIN PE6
|
|
#endif
|
|
|
|
//
|
|
// Control pin of driver/heater/fan power supply
|
|
//
|
|
#define SAFE_POWER_PIN PC13
|
|
|
|
//
|
|
// Steppers
|
|
//
|
|
#define X_STEP_PIN PE2
|
|
#define X_DIR_PIN PE1
|
|
#define X_ENABLE_PIN PE3
|
|
#ifndef X_CS_PIN
|
|
#define X_CS_PIN PE0
|
|
#endif
|
|
|
|
#define Y_STEP_PIN PD5
|
|
#define Y_DIR_PIN PD4
|
|
#define Y_ENABLE_PIN PD6
|
|
#ifndef Y_CS_PIN
|
|
#define Y_CS_PIN PD3
|
|
#endif
|
|
|
|
#define Z_STEP_PIN PA15
|
|
#define Z_DIR_PIN PA8
|
|
#define Z_ENABLE_PIN PD1
|
|
#ifndef Z_CS_PIN
|
|
#define Z_CS_PIN PD0
|
|
#endif
|
|
|
|
#define E0_STEP_PIN PD15
|
|
#define E0_DIR_PIN PD14
|
|
#define E0_ENABLE_PIN PC7
|
|
#ifndef E0_CS_PIN
|
|
#define E0_CS_PIN PC6
|
|
#endif
|
|
|
|
#define E1_STEP_PIN PD11
|
|
#define E1_DIR_PIN PD10
|
|
#define E1_ENABLE_PIN PD13
|
|
#ifndef E1_CS_PIN
|
|
#define E1_CS_PIN PD12
|
|
#endif
|
|
|
|
//
|
|
// Temperature Sensors
|
|
//
|
|
#define TEMP_BED_PIN PA1 // TB
|
|
#define TEMP_0_PIN PA2 // TH0
|
|
#define TEMP_1_PIN PA3 // TH1
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define HEATER_0_PIN PB3 // Heater0
|
|
#define HEATER_1_PIN PB4 // Heater1
|
|
#define HEATER_BED_PIN PD7 // Hotbed
|
|
#define FAN_PIN PB7 // Fan0
|
|
#define FAN1_PIN PB6 // Fan1
|
|
#define FAN2_PIN PB5 // Fan2
|
|
|
|
//
|
|
// Software SPI pins for TMC2130 stepper drivers
|
|
//
|
|
#if ENABLED(TMC_USE_SW_SPI)
|
|
#ifndef TMC_SW_MOSI
|
|
#define TMC_SW_MOSI PE14
|
|
#endif
|
|
#ifndef TMC_SW_MISO
|
|
#define TMC_SW_MISO PA14
|
|
#endif
|
|
#ifndef TMC_SW_SCK
|
|
#define TMC_SW_SCK PE15
|
|
#endif
|
|
#endif
|
|
|
|
#if HAS_TMC_UART
|
|
/**
|
|
* TMC2208/TMC2209 stepper drivers
|
|
*
|
|
* Hardware serial communication ports.
|
|
* If undefined software serial is used according to the pins below
|
|
*/
|
|
//#define X_HARDWARE_SERIAL Serial1
|
|
//#define X2_HARDWARE_SERIAL Serial1
|
|
//#define Y_HARDWARE_SERIAL Serial1
|
|
//#define Y2_HARDWARE_SERIAL Serial1
|
|
//#define Z_HARDWARE_SERIAL Serial1
|
|
//#define Z2_HARDWARE_SERIAL Serial1
|
|
//#define E0_HARDWARE_SERIAL Serial1
|
|
//#define E1_HARDWARE_SERIAL Serial1
|
|
//#define E2_HARDWARE_SERIAL Serial1
|
|
//#define E3_HARDWARE_SERIAL Serial1
|
|
//#define E4_HARDWARE_SERIAL Serial1
|
|
|
|
//
|
|
// Software serial
|
|
//
|
|
#define X_SERIAL_TX_PIN PE0
|
|
#define X_SERIAL_RX_PIN PE0
|
|
|
|
#define Y_SERIAL_TX_PIN PD3
|
|
#define Y_SERIAL_RX_PIN PD3
|
|
|
|
#define Z_SERIAL_TX_PIN PD0
|
|
#define Z_SERIAL_RX_PIN PD0
|
|
|
|
#define E0_SERIAL_TX_PIN PC6
|
|
#define E0_SERIAL_RX_PIN PC6
|
|
|
|
#define E1_SERIAL_TX_PIN PD12
|
|
#define E1_SERIAL_RX_PIN PD12
|
|
|
|
// Reduce baud rate to improve software serial reliability
|
|
#define TMC_BAUD_RATE 19200
|
|
#endif
|
|
|
|
//
|
|
// SD Connection
|
|
//
|
|
#ifndef SDCARD_CONNECTION
|
|
#define SDCARD_CONNECTION LCD
|
|
#endif
|
|
|
|
/**
|
|
* ----- -----
|
|
* NC | 1 2 | GND 5V | 1 2 | GND
|
|
* RESET | 3 4 | PC4 (SD_DETECT) (LCD_D7) PE13 | 3 4 | PE12 (LCD_D6)
|
|
* (MOSI) PA7 | 5 6 PB2 (BTN_EN2) (LCD_D5) PE11 | 5 6 PE10 (LCD_D4)
|
|
* (SD_SS) PA4 | 7 8 | PE7 (BTN_EN1) (LCD_RS) PE9 | 7 8 | PB1 (LCD_EN)
|
|
* (SCK) PA5 | 9 10| PA6 (MISO) (BTN_ENC) PB0 | 9 10| PC5 (BEEPER)
|
|
* ----- -----
|
|
* EXP2 EXP1
|
|
*/
|
|
|
|
#define EXP1_03_PIN PE13
|
|
#define EXP1_04_PIN PE12
|
|
#define EXP1_05_PIN PE11
|
|
#define EXP1_06_PIN PE10
|
|
#define EXP1_07_PIN PE9
|
|
#define EXP1_08_PIN PB1
|
|
#define EXP1_09_PIN PB0
|
|
#define EXP1_10_PIN PC5
|
|
|
|
#define EXP2_03_PIN -1
|
|
#define EXP2_04_PIN PC4
|
|
#define EXP2_05_PIN PA7
|
|
#define EXP2_06_PIN PB2
|
|
#define EXP2_07_PIN PA4
|
|
#define EXP2_08_PIN PE7
|
|
#define EXP2_09_PIN PA5
|
|
#define EXP2_10_PIN PA6
|
|
|
|
//
|
|
// Onboard SD card
|
|
// Must use soft SPI because Marlin's default hardware SPI is tied to LCD's EXP2
|
|
//
|
|
#if SD_CONNECTION_IS(ONBOARD)
|
|
|
|
#define SDIO_SUPPORT // Use SDIO for onboard SD
|
|
#define SDIO_D0_PIN PC8
|
|
#define SDIO_D1_PIN PC9
|
|
#define SDIO_D2_PIN PC10
|
|
#define SDIO_D3_PIN PC11
|
|
#define SDIO_CK_PIN PC12
|
|
#define SDIO_CMD_PIN PD2
|
|
|
|
#elif SD_CONNECTION_IS(LCD)
|
|
|
|
#define CUSTOM_SPI_PINS
|
|
#define SDSS PA4
|
|
#define SD_SS_PIN SDSS
|
|
#define SD_SCK_PIN PA5
|
|
#define SD_MISO_PIN PA6
|
|
#define SD_MOSI_PIN PA7
|
|
#define SD_DETECT_PIN PC4
|
|
|
|
#elif SD_CONNECTION_IS(CUSTOM_CABLE)
|
|
#error "CUSTOM_CABLE is not a supported SDCARD_CONNECTION for this board"
|
|
#endif
|
|
|
|
#if ENABLED(BTT_MOTOR_EXPANSION)
|
|
/**
|
|
* _____ _____
|
|
* NC | · · | GND NC | · · | GND
|
|
* NC | · · | PF12 (M1EN) (M2EN) PG7 | · · | PG6 (M3EN)
|
|
* (M1STP) PB15 | · · PF11 (M1DIR) (M1RX) PG3 | · · PG2 (M1DIAG)
|
|
* (M2DIR) PB12 | · · | PG10 (M2STP) (M2RX) PD10 | · · | PD11 (M2DIAG)
|
|
* (M3DIR) PB13 | · · | PB14 (M3STP) (M3RX) PA8 | · · | PG4 (M3DIAG)
|
|
* ----- -----
|
|
* EXP2 EXP1
|
|
*/
|
|
|
|
// M1 on Driver Expansion Module
|
|
#define E3_STEP_PIN EXP2_05_PIN
|
|
#define E3_DIR_PIN EXP2_06_PIN
|
|
#define E3_ENABLE_PIN EXP2_04_PIN
|
|
#define E3_DIAG_PIN EXP1_06_PIN
|
|
#define E3_CS_PIN EXP1_05_PIN
|
|
#if HAS_TMC_UART
|
|
#define E3_SERIAL_TX_PIN EXP1_05_PIN
|
|
#define E3_SERIAL_RX_PIN EXP1_05_PIN
|
|
#endif
|
|
|
|
// M2 on Driver Expansion Module
|
|
#define E4_STEP_PIN EXP2_08_PIN
|
|
#define E4_DIR_PIN EXP2_07_PIN
|
|
#define E4_ENABLE_PIN EXP1_03_PIN
|
|
#define E4_DIAG_PIN EXP1_08_PIN
|
|
#define E4_CS_PIN EXP1_07_PIN
|
|
#if HAS_TMC_UART
|
|
#define E4_SERIAL_TX_PIN EXP1_07_PIN
|
|
#define E4_SERIAL_RX_PIN EXP1_07_PIN
|
|
#endif
|
|
|
|
// M3 on Driver Expansion Module
|
|
#define E5_STEP_PIN EXP2_10_PIN
|
|
#define E5_DIR_PIN EXP2_09_PIN
|
|
#define E5_ENABLE_PIN EXP1_04_PIN
|
|
#define E5_DIAG_PIN EXP1_10_PIN
|
|
#define E5_CS_PIN EXP1_09_PIN
|
|
#if HAS_TMC_UART
|
|
#define E5_SERIAL_TX_PIN EXP1_09_PIN
|
|
#define E5_SERIAL_RX_PIN EXP1_09_PIN
|
|
#endif
|
|
|
|
#endif // BTT_MOTOR_EXPANSION
|
|
|
|
//
|
|
// LCDs and Controllers
|
|
//
|
|
#if IS_TFTGLCD_PANEL
|
|
|
|
#if ENABLED(TFTGLCD_PANEL_SPI)
|
|
#define TFTGLCD_CS EXP2_08_PIN
|
|
#endif
|
|
|
|
#elif HAS_WIRED_LCD
|
|
|
|
#define BEEPER_PIN EXP1_10_PIN
|
|
#define BTN_ENC EXP1_09_PIN
|
|
|
|
#if ENABLED(CR10_STOCKDISPLAY)
|
|
|
|
#define LCD_PINS_RS EXP1_04_PIN
|
|
|
|
#define BTN_EN1 EXP1_08_PIN
|
|
#define BTN_EN2 EXP1_06_PIN
|
|
|
|
#define LCD_PINS_ENABLE EXP1_03_PIN
|
|
#define LCD_PINS_D4 EXP1_05_PIN
|
|
|
|
// CR10_STOCKDISPLAY default timing is too fast
|
|
#undef BOARD_ST7920_DELAY_1
|
|
#undef BOARD_ST7920_DELAY_2
|
|
#undef BOARD_ST7920_DELAY_3
|
|
|
|
#elif ENABLED(MKS_MINI_12864)
|
|
|
|
#define DOGLCD_A0 EXP1_04_PIN
|
|
#define DOGLCD_CS EXP1_05_PIN
|
|
#define BTN_EN1 EXP2_08_PIN
|
|
#define BTN_EN2 EXP2_06_PIN
|
|
|
|
#else
|
|
|
|
#define LCD_PINS_RS EXP1_07_PIN
|
|
|
|
#define BTN_EN1 EXP2_08_PIN
|
|
#define BTN_EN2 EXP2_06_PIN
|
|
|
|
#define LCD_PINS_ENABLE EXP1_08_PIN
|
|
#define LCD_PINS_D4 EXP1_06_PIN
|
|
|
|
#if ENABLED(FYSETC_MINI_12864)
|
|
#define DOGLCD_CS EXP1_08_PIN
|
|
#define DOGLCD_A0 EXP1_07_PIN
|
|
//#define LCD_BACKLIGHT_PIN -1
|
|
#define LCD_RESET_PIN EXP1_06_PIN // Must be high or open for LCD to operate normally.
|
|
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
|
|
#ifndef RGB_LED_R_PIN
|
|
#define RGB_LED_R_PIN EXP1_05_PIN
|
|
#endif
|
|
#ifndef RGB_LED_G_PIN
|
|
#define RGB_LED_G_PIN EXP1_04_PIN
|
|
#endif
|
|
#ifndef RGB_LED_B_PIN
|
|
#define RGB_LED_B_PIN EXP1_03_PIN
|
|
#endif
|
|
#elif ENABLED(FYSETC_MINI_12864_2_1)
|
|
#define NEOPIXEL_PIN EXP1_05_PIN
|
|
#endif
|
|
#endif // !FYSETC_MINI_12864
|
|
|
|
#if IS_ULTIPANEL
|
|
#define LCD_PINS_D5 EXP1_05_PIN
|
|
#define LCD_PINS_D6 EXP1_04_PIN
|
|
#define LCD_PINS_D7 EXP1_03_PIN
|
|
|
|
#if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
|
|
#define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder
|
|
#endif
|
|
|
|
#endif
|
|
|
|
#endif
|
|
|
|
#endif // HAS_WIRED_LCD
|
|
|
|
// Alter timing for graphical display
|
|
#if HAS_MARLINUI_U8GLIB
|
|
#ifndef BOARD_ST7920_DELAY_1
|
|
#define BOARD_ST7920_DELAY_1 DELAY_NS(96)
|
|
#endif
|
|
#ifndef BOARD_ST7920_DELAY_2
|
|
#define BOARD_ST7920_DELAY_2 DELAY_NS(48)
|
|
#endif
|
|
#ifndef BOARD_ST7920_DELAY_3
|
|
#define BOARD_ST7920_DELAY_3 DELAY_NS(600)
|
|
#endif
|
|
#endif
|
|
|
|
//
|
|
// WIFI
|
|
//
|
|
|
|
/**
|
|
* -------
|
|
* GND | 9 | | 8 | 3.3V
|
|
* (ESP-CS) PB12 | 10 | | 7 | PB15 (ESP-MOSI)
|
|
* 3.3V | 11 | | 6 | PB14 (ESP-MISO)
|
|
* (ESP-IO0) PB10 | 12 | | 5 | PB13 (ESP-CLK)
|
|
* (ESP-IO4) PB11 | 13 | | 4 | NC
|
|
* NC | 14 | | 3 | 3.3V (ESP-EN)
|
|
* (ESP-RX) PD8 | 15 | | 2 | NC
|
|
* (ESP-TX) PD9 | 16 | | 1 | PC14 (ESP-RST)
|
|
* -------
|
|
* WIFI
|
|
*/
|
|
#define ESP_WIFI_MODULE_COM 3 // Must also set either SERIAL_PORT or SERIAL_PORT_2 to this
|
|
#define ESP_WIFI_MODULE_BAUDRATE BAUDRATE // Must use same BAUDRATE as SERIAL_PORT & SERIAL_PORT_2
|
|
#define ESP_WIFI_MODULE_RESET_PIN PC14
|
|
#define ESP_WIFI_MODULE_GPIO0_PIN PB10
|
|
#define ESP_WIFI_MODULE_GPIO4_PIN PB11
|