145 lines
3.3 KiB
C
145 lines
3.3 KiB
C
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
|
|
/**
|
|
* GT2560 V3.0 pin assignment
|
|
*/
|
|
|
|
#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
|
|
#error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"
|
|
#endif
|
|
|
|
#ifndef BOARD_NAME
|
|
#define BOARD_NAME "GT2560 V3.0"
|
|
#endif
|
|
|
|
//
|
|
// Servos
|
|
//
|
|
#define SERVO0_PIN 11 //13 untested 3Dtouch
|
|
|
|
//
|
|
// Limit Switches
|
|
//
|
|
#define X_MIN_PIN 24
|
|
#define X_MAX_PIN 22
|
|
#define Y_MIN_PIN 28
|
|
#define Y_MAX_PIN 26
|
|
#define Z_MIN_PIN 30
|
|
#define Z_MAX_PIN 32
|
|
|
|
//
|
|
// Z Probe (when not Z_MIN_PIN)
|
|
//
|
|
#ifndef Z_MIN_PROBE_PIN
|
|
#define Z_MIN_PROBE_PIN 32
|
|
#endif
|
|
|
|
//
|
|
// Runout Sensor
|
|
//
|
|
#ifndef FIL_RUNOUT_PIN
|
|
#define FIL_RUNOUT_PIN 66
|
|
#endif
|
|
#ifndef FIL_RUNOUT2_PIN
|
|
#define FIL_RUNOUT2_PIN 67
|
|
#endif
|
|
|
|
//
|
|
// Power Recovery
|
|
//
|
|
#define POWER_LOSS_PIN 69 // Pin to detect power loss
|
|
#define POWER_LOSS_STATE LOW
|
|
|
|
//
|
|
// Steppers
|
|
//
|
|
#define X_STEP_PIN 37
|
|
#define X_DIR_PIN 39
|
|
#define X_ENABLE_PIN 35
|
|
|
|
#define Y_STEP_PIN 31
|
|
#define Y_DIR_PIN 33
|
|
#define Y_ENABLE_PIN 29
|
|
|
|
#define Z_STEP_PIN 25
|
|
#define Z_DIR_PIN 23
|
|
#define Z_ENABLE_PIN 27
|
|
|
|
#define E0_STEP_PIN 46
|
|
#define E0_DIR_PIN 44
|
|
#define E0_ENABLE_PIN 12
|
|
|
|
#define E1_STEP_PIN 49
|
|
#define E1_DIR_PIN 47
|
|
#define E1_ENABLE_PIN 48
|
|
|
|
//
|
|
// Temperature Sensors
|
|
//
|
|
#define TEMP_0_PIN 11 // Analog Input
|
|
#define TEMP_1_PIN 9 // Analog Input
|
|
#define TEMP_2_PIN 1 // Analog Input
|
|
#define TEMP_BED_PIN 10 // Analog Input
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define HEATER_0_PIN 10
|
|
#define HEATER_1_PIN 3
|
|
#define HEATER_2_PIN 1
|
|
#define HEATER_BED_PIN 4
|
|
#define FAN_PIN 9
|
|
//#define FAN1_PIN 8
|
|
//#define FAN2_PIN 7
|
|
|
|
//
|
|
// Misc. Functions
|
|
//
|
|
#define SD_DETECT_PIN 38
|
|
#define SDSS 53
|
|
#define LED_PIN 6
|
|
#define PS_ON_PIN 12
|
|
#define SUICIDE_PIN 54 // This pin must be enabled at boot to keep power flowing
|
|
|
|
#ifndef CASE_LIGHT_PIN
|
|
#define CASE_LIGHT_PIN 6 // 21
|
|
#endif
|
|
|
|
//
|
|
// LCD Controller
|
|
//
|
|
#define BEEPER_PIN 18
|
|
|
|
#define LCD_PINS_RS 20
|
|
#define LCD_PINS_ENABLE 17
|
|
#define LCD_PINS_D4 16
|
|
#define LCD_PINS_D5 21
|
|
#define LCD_PINS_D6 5
|
|
#define LCD_PINS_D7 36
|
|
|
|
#if ENABLED(NEWPANEL)
|
|
#define BTN_EN1 42
|
|
#define BTN_EN2 40
|
|
#define BTN_ENC 19
|
|
#endif
|