110 lines
3.1 KiB
C
110 lines
3.1 KiB
C
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
#pragma once
|
|
|
|
/**
|
|
* Pin assignments for the MKS RUMBA32
|
|
*
|
|
* https://github.com/makerbase-mks/MKS-RUMBA32
|
|
*
|
|
* The MKS and Aus3D versions have the same pinout but the MKS version
|
|
* has some added resistors and LEDs. The resistors needed for the
|
|
* TMC2208/9 UART interface are among the additions. Also added were
|
|
* connectors and resistors dedicated to the TMC2130 sensorless homing
|
|
* interface.
|
|
*/
|
|
|
|
#define BOARD_INFO_NAME "MKS RUMBA32"
|
|
|
|
#define RUMBA32_V1_0
|
|
#define ENABLE_SPI1
|
|
//#define I2C_EEPROM
|
|
|
|
#include "pins_RUMBA32_common.h"
|
|
|
|
//
|
|
// Software SPI pins for TMC2130 stepper drivers
|
|
//
|
|
#if ENABLED(TMC_USE_SW_SPI)
|
|
#ifndef TMC_SW_MOSI
|
|
#define TMC_SW_MOSI PA7
|
|
#endif
|
|
#ifndef TMC_SW_MISO
|
|
#define TMC_SW_MISO PA6
|
|
#endif
|
|
#ifndef TMC_SW_SCK
|
|
#define TMC_SW_SCK PA5
|
|
#endif
|
|
#endif
|
|
|
|
#if HAS_TMC_UART
|
|
/**
|
|
* TMC2208/TMC2209 stepper drivers
|
|
*
|
|
* Hardware serial communication ports.
|
|
* If undefined software serial is used according to the pins below
|
|
*/
|
|
//#define X_HARDWARE_SERIAL Serial
|
|
//#define X2_HARDWARE_SERIAL Serial1
|
|
//#define Y_HARDWARE_SERIAL Serial1
|
|
//#define Y2_HARDWARE_SERIAL Serial1
|
|
//#define Z_HARDWARE_SERIAL Serial1
|
|
//#define Z2_HARDWARE_SERIAL Serial1
|
|
//#define E0_HARDWARE_SERIAL Serial1
|
|
//#define E1_HARDWARE_SERIAL Serial1
|
|
//#define E2_HARDWARE_SERIAL Serial1
|
|
//#define E3_HARDWARE_SERIAL Serial1
|
|
//#define E4_HARDWARE_SERIAL Serial1
|
|
|
|
//
|
|
// Software serial
|
|
//
|
|
#define X_SERIAL_TX_PIN PA3
|
|
#define X_SERIAL_RX_PIN PC14
|
|
|
|
#define Y_SERIAL_TX_PIN PA4
|
|
#define Y_SERIAL_RX_PIN PE4
|
|
|
|
#define Z_SERIAL_TX_PIN PD13
|
|
#define Z_SERIAL_RX_PIN PE0
|
|
|
|
#define E0_SERIAL_TX_PIN PD14
|
|
#define E0_SERIAL_RX_PIN PC13
|
|
|
|
#define E1_SERIAL_TX_PIN PD15
|
|
#define E1_SERIAL_RX_PIN PD5
|
|
|
|
#define E2_SERIAL_TX_PIN PD12
|
|
#define E2_SERIAL_RX_PIN PD1
|
|
#endif
|
|
|
|
//
|
|
// LCD / Controller
|
|
//
|
|
|
|
// Alter timing for graphical display
|
|
#if HAS_GRAPHICAL_LCD
|
|
#define BOARD_ST7920_DELAY_1 DELAY_NS(96)
|
|
#define BOARD_ST7920_DELAY_2 DELAY_NS(48)
|
|
#define BOARD_ST7920_DELAY_3 DELAY_NS(600)
|
|
#endif
|