121 lines
3 KiB
C++
121 lines
3 KiB
C++
#ifdef TARGET_LPC1768
|
|
|
|
// ---------------------
|
|
// Userspace entry point
|
|
// ---------------------
|
|
extern void setup();
|
|
extern void loop();
|
|
|
|
extern "C" {
|
|
#include <lpc17xx_gpio.h>
|
|
}
|
|
|
|
#include <usb/usb.h>
|
|
#include <usb/usbcfg.h>
|
|
#include <usb/usbhw.h>
|
|
#include <usb/usbcore.h>
|
|
#include <usb/cdc.h>
|
|
#include <usb/cdcuser.h>
|
|
#include <usb/mscuser.h>
|
|
|
|
extern "C" {
|
|
#include <debug_frmwrk.h>
|
|
#include <chanfs/diskio.h>
|
|
#include <chanfs/ff.h>
|
|
}
|
|
|
|
#include "../../inc/MarlinConfig.h"
|
|
#include "HAL.h"
|
|
#include "fastio.h"
|
|
#include "HAL_timers.h"
|
|
#include <stdio.h>
|
|
#include <stdarg.h>
|
|
#include <Arduino.h>
|
|
#include "serial.h"
|
|
#include "LPC1768_PWM.h"
|
|
|
|
static __INLINE uint32_t SysTick_Config(uint32_t ticks) {
|
|
if (ticks > SysTick_LOAD_RELOAD_Msk) return 1;
|
|
|
|
SysTick->LOAD = (ticks & SysTick_LOAD_RELOAD_Msk) - 1; // Set reload register
|
|
SysTick->VAL = 0; // Load the SysTick Counter Value
|
|
SysTick->CTRL = SysTick_CTRL_CLKSOURCE_Msk |
|
|
SysTick_CTRL_TICKINT_Msk |
|
|
SysTick_CTRL_ENABLE_Msk; // Enable SysTick IRQ and SysTick Timer
|
|
|
|
NVIC_SetPriority(SysTick_IRQn, NVIC_EncodePriority(0, 0, 0)); // Set Priority for Cortex-M3 System Interrupts
|
|
return 0;
|
|
}
|
|
|
|
extern "C" {
|
|
extern int isLPC1769();
|
|
extern void disk_timerproc(void);
|
|
volatile uint32_t _millis;
|
|
|
|
void SysTick_Handler(void) {
|
|
++_millis;
|
|
disk_timerproc();
|
|
}
|
|
|
|
// Runs after clock init and before global static constructors
|
|
void SystemPostInit() {
|
|
_millis = 0; // Initialise the millisecond counter value;
|
|
SysTick_Config(SystemCoreClock / 1000); // Start millisecond global counter
|
|
|
|
// Runs before setup() need to configure LED_PIN and use to indicate succsessful bootloader execution
|
|
#if PIN_EXISTS(LED)
|
|
SET_DIR_OUTPUT(LED_PIN);
|
|
WRITE_PIN_CLR(LED_PIN);
|
|
|
|
//MKS-SBASE has 3 other LEDS the bootloader uses during flashing, clear them
|
|
SET_DIR_OUTPUT(P1_19);
|
|
WRITE_PIN_CLR(P1_19);
|
|
SET_DIR_OUTPUT(P1_20);
|
|
WRITE_PIN_CLR(P1_20);
|
|
SET_DIR_OUTPUT(P1_21);
|
|
WRITE_PIN_CLR(P1_21);
|
|
|
|
for (int i = 0; i < 6; ++i) {
|
|
TOGGLE(LED_PIN);
|
|
delay(100);
|
|
}
|
|
#endif
|
|
}
|
|
}
|
|
|
|
extern uint32_t MSC_SD_Init(uint8_t pdrv);
|
|
|
|
int main(void) {
|
|
|
|
(void)MSC_SD_Init(0);
|
|
|
|
USB_Init(); // USB Initialization
|
|
USB_Connect(TRUE); // USB Connect
|
|
|
|
const uint32_t usb_timeout = millis() + 2000;
|
|
while (!USB_Configuration && PENDING(millis(), usb_timeout)) {
|
|
delay(50);
|
|
#if PIN_EXISTS(LED)
|
|
TOGGLE(LED_PIN); // Flash fast while USB initialisation completes
|
|
#endif
|
|
}
|
|
|
|
#if NUM_SERIAL > 0
|
|
MYSERIAL0.begin(BAUDRATE);
|
|
#if NUM_SERIAL > 1
|
|
MYSERIAL1.begin(BAUDRATE);
|
|
#endif
|
|
SERIAL_PRINTF("\n\necho:%s (%dMhz) Initialised\n", isLPC1769() ? "LPC1769" : "LPC1768", SystemCoreClock / 1000000);
|
|
SERIAL_FLUSHTX();
|
|
#endif
|
|
|
|
HAL_timer_init();
|
|
|
|
LPC1768_PWM_init();
|
|
|
|
setup();
|
|
for (;;) loop();
|
|
}
|
|
|
|
#endif // TARGET_LPC1768
|