muele-marlin/Marlin/src/pins/stm32f4/pins_FYSETC_CHEETAH_V20.h
ellensp 79ee2fa20a
EXP headers for RAMPS 1.x (#21054)
Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>
2021-02-15 05:15:08 -06:00

272 lines
8.1 KiB
C

/**
* Marlin 3D Printer Firmware
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <https://www.gnu.org/licenses/>.
*
*/
#pragma once
#if NOT_TARGET(STM32F4)
#error "Oops! Select an STM32F4 board in 'Tools > Board.'"
#endif
#define DEFAULT_MACHINE_NAME "3D Printer"
#define BOARD_INFO_NAME "FYSETC Cheetah V2.0"
#define BOARD_WEBSITE_URL "fysetc.com"
// USB Flash Drive support
//#define HAS_OTG_USB_HOST_SUPPORT
// Ignore temp readings during development.
//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
#if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION)
#define FLASH_EEPROM_EMULATION
#define FLASH_EEPROM_LEVELING
#define FLASH_SECTOR 2
#define FLASH_UNIT_SIZE 0x4000 // 16k
#define FLASH_ADDRESS_START 0x8008000
#endif
//
// Z Probe
//
#if ENABLED(BLTOUCH)
#error "You need to set jumper to 5v for Bltouch, then comment out this line to proceed."
#define SERVO0_PIN PA0
#elif !defined(Z_MIN_PROBE_PIN)
#define Z_MIN_PROBE_PIN PA0
#endif
//
// Limit Switches
//
#define X_STOP_PIN PB4
#define Y_STOP_PIN PB3
#define Z_STOP_PIN PB1
//
// Filament runout
//
#define FIL_RUNOUT_PIN PB5
//
// Steppers
//
#define X_STEP_PIN PC0
#define X_DIR_PIN PC1
#define X_ENABLE_PIN PA8
#define Y_STEP_PIN PC14
#define Y_DIR_PIN PC13
#define Y_ENABLE_PIN PC15
#define Z_STEP_PIN PB9
#define Z_DIR_PIN PB8
#define Z_ENABLE_PIN PC2
#define E0_STEP_PIN PB2
#define E0_DIR_PIN PA15
#define E0_ENABLE_PIN PD2
#if HAS_TMC_UART
#define X_HARDWARE_SERIAL Serial2
#define Y_HARDWARE_SERIAL Serial2
#define Z_HARDWARE_SERIAL Serial2
#define E0_HARDWARE_SERIAL Serial2
// Default TMC slave addresses
#ifndef X_SLAVE_ADDRESS
#define X_SLAVE_ADDRESS 0
#endif
#ifndef Y_SLAVE_ADDRESS
#define Y_SLAVE_ADDRESS 2
#endif
#ifndef Z_SLAVE_ADDRESS
#define Z_SLAVE_ADDRESS 1
#endif
#ifndef E0_SLAVE_ADDRESS
#define E0_SLAVE_ADDRESS 3
#endif
#endif
//
// Heaters / Fans
//
#define HEATER_0_PIN PC6
#define HEATER_BED_PIN PC7
#ifndef FAN_PIN
#define FAN_PIN PA1
#endif
#define FAN1_PIN PC8
//
// Temperature Sensors
//
#define TEMP_BED_PIN PC5 // Analog Input
#define TEMP_0_PIN PC4 // Analog Input
//
// Misc. Functions
//
#define SDSS PA4
#define SD_DETECT_PIN PC3
#ifndef RGB_LED_R_PIN
#define RGB_LED_R_PIN PB0
#endif
#ifndef RGB_LED_G_PIN
#define RGB_LED_G_PIN PB7
#endif
#ifndef RGB_LED_B_PIN
#define RGB_LED_B_PIN PB6
#endif
/**
* _____ _____
* 5V | 1 2 | GND 5V | 1 2 | GND
* RESET | 3 4 | PC3 (SD_DETECT) (LCD_D7) PB7 | 3 4 | PB6 (LCD_D6)
* (SD_MOSI) PA7 5 6 | PC11 (BTN_EN2) (LCD_D5) PB14 5 6 | PB13 (LCD_D4)
* (SD_SS) PA4 | 7 8 | PC10 (BTN_EN1) (LCD_RS) PB12 | 7 8 | PB15 (LCD_EN)
* (SD_SCK) PA5 | 9 10| PA6 (SD_MISO) (BTN_ENC) PC12 | 9 10| PC9 (BEEPER)
* ----- -----
* EXP2 EXP1
*/
/**
* _____
* (BEEPER) PC9 | 1 2 | PC12 (BTN_ENC)
* (BTN_EN1) PC10 | 3 4 | PB14 (LCD_D5/MISO)
* (BTN_EN2) PC11 5 6 | PB13 (LCD_D4/SCK)
* (LCD_RS) PB12 | 7 8 | PB15 (LCD_EN/MOSI)
* GND | 9 10| 5V
* -----
* EXP3
*/
#define EXP1_03_PIN PB7
#define EXP1_04_PIN PB6
#define EXP1_05_PIN PB14
#define EXP1_06_PIN PB13
#define EXP1_07_PIN PB12
#define EXP1_08_PIN PB15
#define EXP1_09_PIN PC12
#define EXP1_10_PIN PC9
#define EXP2_03_PIN -1
#define EXP2_04_PIN PC3
#define EXP2_05_PIN PA7
#define EXP2_06_PIN PC11
#define EXP2_07_PIN PA4
#define EXP2_08_PIN PC10
#define EXP2_09_PIN PA5
#define EXP2_10_PIN PA6
#if HAS_WIRED_LCD
#define BEEPER_PIN EXP1_10_PIN
#define BTN_ENC EXP1_09_PIN
#if ENABLED(CR10_STOCKDISPLAY)
#define LCD_PINS_RS EXP1_07_PIN
#define BTN_EN1 EXP2_08_PIN
#define BTN_EN2 EXP2_06_PIN
#define LCD_PINS_ENABLE EXP1_08_PIN
#define LCD_PINS_D4 EXP1_06_PIN
// CR10_STOCKDISPLAY default timing is too fast
#undef BOARD_ST7920_DELAY_1
#undef BOARD_ST7920_DELAY_2
#undef BOARD_ST7920_DELAY_3
#elif ENABLED(MKS_MINI_12864)
#define DOGLCD_A0 EXP1_04_PIN
#define DOGLCD_CS EXP1_05_PIN
#define BTN_EN1 EXP2_08_PIN
#define BTN_EN2 EXP2_06_PIN
#else
#define LCD_PINS_RS EXP1_07_PIN
#define BTN_EN1 EXP2_06_PIN
#define BTN_EN2 EXP2_08_PIN
#define LCD_PINS_ENABLE EXP1_08_PIN
#define LCD_PINS_D4 EXP1_06_PIN
#if ENABLED(FYSETC_MINI_12864)
#define DOGLCD_CS EXP1_08_PIN
#define DOGLCD_A0 EXP1_07_PIN
//#define LCD_BACKLIGHT_PIN -1
#define LCD_RESET_PIN EXP1_06_PIN // Must be high or open for LCD to operate normally.
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
#ifndef RGB_LED_R_PIN
#define RGB_LED_R_PIN EXP1_05_PIN
#endif
#ifndef RGB_LED_G_PIN
#define RGB_LED_G_PIN EXP1_04_PIN
#endif
#ifndef RGB_LED_B_PIN
#define RGB_LED_B_PIN EXP1_03_PIN
#endif
#elif ENABLED(FYSETC_MINI_12864_2_1)
#define NEOPIXEL_PIN EXP1_05_PIN
#endif
#endif // !FYSETC_MINI_12864
#if IS_ULTIPANEL
#define LCD_PINS_D5 EXP1_05_PIN
#define LCD_PINS_D6 EXP1_04_PIN
#define LCD_PINS_D7 EXP1_03_PIN
#if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
#define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder
#endif
#endif
#endif
#endif // HAS_WIRED_LCD
// Alter timing for graphical display
#if HAS_MARLINUI_U8GLIB
#ifndef BOARD_ST7920_DELAY_1
#define BOARD_ST7920_DELAY_1 DELAY_NS(96)
#endif
#ifndef BOARD_ST7920_DELAY_2
#define BOARD_ST7920_DELAY_2 DELAY_NS(48)
#endif
#ifndef BOARD_ST7920_DELAY_3
#define BOARD_ST7920_DELAY_3 DELAY_NS(600)
#endif
#endif
#if ENABLED(TOUCH_UI_FTDI_EVE)
#define BEEPER_PIN EXP1_10_PIN
#define CLCD_MOD_RESET EXP2_08_PIN
#define CLCD_SPI_CS EXP2_06_PIN
#endif