forked from pub-solar/os
109 lines
3.4 KiB
Markdown
109 lines
3.4 KiB
Markdown
# ISO
|
|
|
|
Making and writing an installable iso for `hosts/NixOS.nix` is as simple as:
|
|
```sh
|
|
flk iso NixOS
|
|
|
|
dd bs=4M if=result/iso/*.iso of=/dev/$your_installation_device \
|
|
status=progress oflag=sync
|
|
```
|
|
|
|
This works for any file matching `hosts/*.nix` excluding `default.nix`.
|
|
|
|
## Remote access to the live installer
|
|
|
|
The iso live installer comes preconfigured with a network configuration
|
|
which announces it's hostname via [MulticastDNS][mDNS] as `hostname.local`,
|
|
that is `NixOS.local` in the above example.
|
|
|
|
In the rare case that [MulticastDNS][mDNS] is not availabe or turned off
|
|
in your network, there is a static link-local IPv6 address configured to
|
|
`fe80::47`(mnemonic from the letter's position in the english alphabet:
|
|
`n=14 i=9 x=24; 47 = n+i+x`).
|
|
|
|
Provided that you have added your public key to the authorized keys of the
|
|
`nixos` user:
|
|
|
|
```nix
|
|
{ ... }:
|
|
{
|
|
users.users.nixos.openssh.authorizedKeys.keyFiles = [
|
|
../secrets/path/to/key.pub
|
|
];
|
|
}
|
|
```
|
|
|
|
You can then ssh into the live installer through one of the
|
|
following options:
|
|
|
|
```console
|
|
ssh nixos@NixOS.local
|
|
|
|
ssh nixos@fe80::47%eno1 # where eno1 is your network interface on which you are linked to the target
|
|
```
|
|
|
|
_Note: the [static link-local IPv6 address][staticLLA] and [MulticastDNS][mDNS] is only
|
|
configured on the live installer. If you wish to enable [MulticastDNS][mDNS]
|
|
for your environment, you ought to configure that in a regular [profile](../../profiles)._
|
|
|
|
## EUI-64 LLA & Host Identity
|
|
|
|
The iso's IPv6 Link Local Address (LLA) is configured with a static 64-bit Extended
|
|
Unique Identifiers (EUI-64) that is derived from the host interface's Message
|
|
Authentication Code (MAC) address.
|
|
|
|
After a little while (a few seconds), you can remotely disvover this unique and host
|
|
specific address over [NDP][NDP] for example with:
|
|
|
|
```console
|
|
ip -6 neigh show # also shows fe80::47
|
|
```
|
|
|
|
***This LLA is stable for the host, unless you need to swap that particular network card.***
|
|
Under this reservation, though, you may use this EUI-64 to wire up a specific
|
|
(cryptographic) host identity.
|
|
|
|
## Bootstrap Target Machine
|
|
|
|
_Note: nothing prevents you from remotely exceuting the boostrapping process._
|
|
|
|
Once your target host has booted into the live iso, you need to partion
|
|
and format your disk according to the [official manual][manual].
|
|
|
|
### Mount partitions
|
|
|
|
Then properly mount the formatted partitions at `/mnt`, so that you can
|
|
install your system to those new partitions.
|
|
|
|
Mount `nixos` partition to `/mnt` and — for UEFI — `boot`
|
|
partition to `/mnt/boot`:
|
|
|
|
```console
|
|
$ mount /dev/disk/by-label/nixos /mnt
|
|
$ mkdir -p /mnt/boot && mount /dev/disk/by-label/boot /mnt/boot # UEFI only
|
|
$ swapon /dev/$your_swap_partition
|
|
```
|
|
|
|
### Install
|
|
|
|
Install using the `flk` wrapper baked into the iso off of a copy of devos
|
|
from the time the iso was built:
|
|
|
|
```console
|
|
$ cd /iso/devos
|
|
$ nix develop
|
|
$ flk install NixOS --impure # use same host as above
|
|
```
|
|
|
|
<!-- TODO: find out why --impure is necesary / PRs welcome! -->
|
|
|
|
_Note: You _could_ install another machine than the one your iso was built for,
|
|
but the iso doesn't carry all the necesary build artifacts so the target would
|
|
start to build the missing parts on demand instead of substituting them from
|
|
the iso itself._
|
|
|
|
[manual]: https://nixos.org/manual/nixos/stable/index.html#sec-installation-partitioning
|
|
[mDNS]: https://en.wikipedia.org/wiki/Multicast_DNS
|
|
[NDP]: https://en.wikipedia.org/wiki/Neighbor_Discovery_Protocol
|
|
[staticLLA]: https://tools.ietf.org/html/rfc7404
|