180 lines
6 KiB
Markdown
180 lines
6 KiB
Markdown
# Embassy RP Skeleton
|
|
The **Embassy RP Skeleton** repository is a project template intended as a starting point for developing your own
|
|
firmware for the [`rp2040`][1] based on the [`embassy`][2] asynchronous embedded development framework for [Rust][12].
|
|
|
|
It includes all of the [`knurling-rs`][3] tooling ([`defmt`][4], [`defmt-rtt`][4], [`panic-probe`][4], [`flip-link`][5],
|
|
[`probe-run`][6]) to enhance the embedded development process.
|
|
|
|
The default [`cargo`][7] runner is configured as [`probe-run`][6], so you can build, flash and run your firmware _with_
|
|
output from the device via a CMSIS-DAP compatible debug probe with the command:
|
|
|
|
```shell
|
|
$ cargo run
|
|
```
|
|
|
|
If you want to use a different runner with your debugger (e.g., [`cargo-embed`][8], [`probe-rs-debugger`][9], etc.) or
|
|
if you _aren't_ using a debugger and want the runner to flash the firmware via USB (e.g., [`elf2uf2-rs`][10],
|
|
[`picotool`][11], etc.) then see: [Alternative Runners][17]
|
|
|
|
## Table of Contents
|
|
1. [Requirements](#requirements)
|
|
2. [Setup](#setup)
|
|
1. [System Setup](#system-setup)
|
|
2. [Probe Setup](#probe-setup)
|
|
3. [Hardware Setup](#hardware-setup)
|
|
3. [Usage](#usage)
|
|
6. [Appendix](#appendix)
|
|
|
|
## Requirements
|
|
* Ubuntu
|
|
* Raspberry Pi Pico
|
|
* CMSIS-DAP Debug Probe (*or* another Raspberry Pi Pico)
|
|
* Rust Toolchain ([`cargo`][7], [`rustup`][13])
|
|
|
|
## Setup
|
|
### System Setup
|
|
1. Install [Rust][12] and [`cargo`][7] using [`rustup`][13]
|
|
```shell
|
|
# Install `rustup` for Rust Toolchain
|
|
$ curl --proto '=https' --tlsv1.2 -sSf https://sh.rustup.rs | sh
|
|
```
|
|
|
|
2. Install Cortex-M Target Toolchain Support for [`Rust`][12]
|
|
```shell
|
|
# Install `thumbv6m-none-eabi` Target for `rp2040`
|
|
$ rustup target add thumbv6m-none-eabi
|
|
```
|
|
|
|
3. Install [`probe-run`][6]
|
|
```shell
|
|
# Install Linux Dependencies
|
|
$ sudo apt install -y libusb-1.0-0-dev libudev-dev
|
|
|
|
# Install `probe-run`
|
|
$ cargo install probe-run
|
|
|
|
# (Optional) Install `udev` Rules and Reload
|
|
$ sudo curl https://probe.rs/files/69-probe-rs.rules -o /etc/udev/rules.d/69-probe-rs.rules
|
|
$ sudo udevadm control --reload
|
|
$ sudo udevadm trigger
|
|
|
|
# (Optional) Add User to `plugdev` Group
|
|
$ sudo usermod -aG plugdev $USER
|
|
```
|
|
|
|
4. Install [`flip-link`][5]
|
|
```shell
|
|
# Install `flip-link`
|
|
$ $ cargo install flip-link
|
|
```
|
|
|
|
### Probe Setup
|
|
You can use a Raspberry Pi Pico as a CMSIS-DAP compatible debug probe.
|
|
|
|
1. Download CMSIS-DAP debugger firmware [`DapperMime`][14] for the Raspberry Pi Pico
|
|
2. Boot the Raspberry Pi Pico in "Bootloader Mode" by holding the _BOOTSEL_ button while plugging it in
|
|
3. Open the mounted Raspberry Pi Pico storage device
|
|
4. Copy the `raspberry_pi_pico-DapperMime.uf2` onto the Raspberry Pi Pico
|
|
5. Firmware will be flashed to the Raspberry Pi Pico and it will disconnect
|
|
|
|
Any CMSIS-DAP compatible debug probe can be used with [`probe-run`][6]. For a short list of alternative compatible debug
|
|
probes see: [Alternative Debug Probes][15].
|
|
|
|
### Hardware Setup
|
|
#### Connecting the Raspberry Pi Pico Debug Probe
|
|
The diagram below shows the wiring loom between Raspberry Pi Pico A (left) and Raspberry Pi Pico B (right), configuring
|
|
Raspberry Pi Pico A as a debug probe.
|
|
|
|
![Raspberry Pi Pico Debug Probe Wiring][18]
|
|
|
|
The connections in the diagram above are listed below.
|
|
|
|
```
|
|
Pico A GND -> Pico B GND
|
|
Pico A GP2 -> Pico B SWCLK
|
|
Pico A GP3 -> Pico B SWDIO
|
|
Pico A GP4/UART1 TX -> Pico B GP1/UART0 RX
|
|
Pico A GP5/UART1 RX -> Pico B GP0/UART0 TX
|
|
Pico A VSYS -> Pico B VSYS
|
|
```
|
|
|
|
For more information on the wiring loom, see:
|
|
[Getting Started with Raspberry Pi Pico > Appendix A > Picoprobe Wiring][16]
|
|
|
|
#### Raspberry Pi Pico Dev Board
|
|
Alternatively, a custom printed Raspberry Pi Pico Dev Board can be used to enhance development with:
|
|
|
|
* Debug Probe Host (Raspberry Pi Pico)
|
|
* Detachable Target (Raspberry Pi Pico)
|
|
* Serial Interface
|
|
* Reset Button
|
|
* Breakout Pins
|
|
* Selection of _VSys_ or _VBus_ Power Sources
|
|
|
|
![Raspberry Pi Pico Dev Board Debugging][19]
|
|
|
|
For more information on printing and constructing your own custom Raspberry Pi Pico Dev Board, see:
|
|
[Raspberry Pi Pico Dev Board][20]
|
|
|
|
## Usage
|
|
To run the firmware in debug mode:
|
|
```shell
|
|
$ cargo run
|
|
```
|
|
|
|
To run the firmware in release mode:
|
|
```shell
|
|
$ cargo run --release
|
|
```
|
|
|
|
To change the default [`defmt`][4] log level, see `.cargo/config.toml`:
|
|
```toml
|
|
[env]
|
|
DEFMT_LOG = "trace"
|
|
```
|
|
|
|
You can also set the log level inline:
|
|
```shell
|
|
$ DEFMT_LOG=debug cargo run
|
|
$ DEFMT_LOG=error cargo run --release
|
|
```
|
|
|
|
## Appendix
|
|
**TODO**
|
|
- Links, resources, references and guides
|
|
|
|
<!-- Reference -->
|
|
[1]: https://www.raspberrypi.com/documentation/microcontrollers/rp2040.html
|
|
[2]: https://embassy.dev/dev/index.html
|
|
[3]: https://github.com/knurling-rs/app-template
|
|
[4]: https://github.com/knurling-rs/defmt
|
|
[5]: https://github.com/knurling-rs/flip-link
|
|
[6]: https://github.com/knurling-rs/probe-run
|
|
[7]: https://doc.rust-lang.org/cargo/
|
|
[8]: https://github.com/probe-rs/cargo-embed
|
|
[9]: https://github.com/probe-rs/vscode
|
|
[10]: https://github.com/JoNil/elf2uf2-rs
|
|
[11]: https://github.com/raspberrypi/picotool
|
|
[12]: https://www.rust-lang.org/
|
|
[13]: https://rustup.rs/
|
|
[14]: https://github.com/majbthrd/DapperMime
|
|
[15]: https://github.com/rp-rs/rp2040-project-template/blob/main/debug_probes.md
|
|
[16]: https://datasheets.raspberrypi.com/pico/getting-started-with-pico.pdf#%5B%7B%22num%22%3A64%2C%22gen%22%3A0%7D%2C%7B%22name%22%3A%22XYZ%22%7D%2C115%2C696.992%2Cnull%5D
|
|
[17]: https://github.com/rp-rs/rp2040-project-template#alternative-runners
|
|
[18]: https://user-images.githubusercontent.com/12226419/134785445-5f651d5a-eda9-4e94-8860-d2ef619dc27a.png
|
|
[19]: https://timsavage.github.io/rpi-pico-devboard/assets/images/devboard-debugging.jpg
|
|
[20]: https://timsavage.github.io/rpi-pico-devboard/
|
|
|
|
<!-- Other Stuff -->
|
|
<!--
|
|
https://github.com/rust-embedded/awesome-embedded-rust
|
|
https://github.com/rp-rs/rp2040-project-template
|
|
https://timsavage.github.io/rpi-pico-devboard/
|
|
https://github.com/embassy-rs/embassy
|
|
https://probe.rs/docs/getting-started/probe-setup/
|
|
https://embedded-trainings.ferrous-systems.com/
|
|
https://docs.rust-embedded.org/book/
|
|
https://github.com/ferrous-systems/teaching-material
|
|
https://reltech.substack.com/p/getting-started-with-rust-on-a-raspberry
|
|
-->
|