Roxy-3D
0780913848
IDEX Improvements ( #11848 )
2018-09-17 01:06:22 -05:00
Thomas Moore
c437bb08f1
Overhaul of the planner ( #11578 )
...
- Move FWRETRACT to the planner
- Combine leveling, skew, etc. in a single modifier method
- Have kinematic and non-kinematic moves call one planner method
2018-09-16 21:24:15 -05:00
Holger Müller
1a6f2b29b8
Add support for Triple-Z steppers/endstops
2018-09-16 00:35:58 -05:00
Sam Lane
1b6bc19427
Add external closed loop controller support
2018-09-10 03:17:17 -05:00
Alexander Amelkin
bc1ba998b2
[2.0.x] Fix undefined symbol 'g29_in_progress' ( #11781 )
2018-09-09 22:06:03 -05:00
InsanityAutomation
bad225dc04
Fix mesh leveling compile errors ( #11768 )
2018-09-09 04:19:48 -05:00
Scott Lahteine
d1ceaf5550
[2.0.x] Followup to IDEX changes ( #11707 )
2018-09-03 23:15:31 -05:00
Roxy-3D
7680b64aa6
IDEX clean up ( #11690 )
2018-09-02 10:18:59 -05:00
Colin Gilgenbach
593d5375ea
Fix G28 resetting DUAL_NOZZLE_DUPLICATION_MODE ( #11605 )
...
There's no reason for G28 to reset DUAL_NOZZLE_DUPLICATION_MODE, because it only affects the E stepper, unlike DUAL_X_CARRIAGE which affects the X steppers as well.
2018-08-21 23:42:55 -05:00
Scott Lahteine
0af22549a6
Allow G33 to compile with no LCD
2018-08-11 22:32:09 -05:00
Giuliano
4237c3d9f8
[2.0.x] different bltouch init ( #11135 )
2018-07-26 05:04:09 -05:00
etagle
1367df2875
Replace double with float, optimize calculation
2018-07-04 22:28:56 -05:00
Scott Lahteine
d960d448fa
Optimize calculations with LROUND
2018-07-04 22:22:28 -05:00
Scott Lahteine
e0ab8acf19
Add "Marlin Dev Mode" option
2018-07-02 22:55:21 -05:00
Scott Lahteine
c51e27d11d
Do a hard kill for failed homing moves ( #11161 )
2018-06-30 21:54:07 -05:00
Scott Lahteine
90ba77ea0f
Lose the old HOMEAXIS macro
2018-06-30 18:13:13 -05:00
Scott Lahteine
a431013eb7
Fix G33 compile warning
2018-06-29 23:17:51 -05:00
Giuliano
cce0523a95
[2.0.x] reset bltouch on home ( #11018 )
...
Added reset bltouch instead. This ensure properly stow even when in error.
2018-06-13 14:09:13 -05:00
Karl Andersson
e0276d2f32
Official STMicroelectronics Arduino Core STM32F4 HAL compatibility ( #11006 )
2018-06-12 18:38:00 -05:00
Scott Lahteine
f2c3b0d476
Use bit flags for homed/known
2018-06-11 22:05:16 -05:00
Robert Mendon
86170e6a66
[2.0.x] Add O (optional) flag to G28/G29 ( #10913 )
2018-06-11 21:51:48 -05:00
Giuliano
f1cdfe3dfd
[2.0.x] stow bltouch before start homing ( #10987 )
2018-06-10 16:27:14 -05:00
Eduardo José Tagle
6f330f397e
[2.0.x] Buffer overflow and scroll fix, UTF8 cleanup ( #10844 )
2018-05-25 23:32:37 -05:00
Scott Lahteine
99ecdf59af
Smarter MIN, MAX, ABS macros
...
Use macros that explicitly avoid double-evaluation and can be used for any datatype, replacing `min`, `max`, `abs`, `fabs`, `labs`, and `FABS`.
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
2018-05-13 04:52:56 -05:00
Scott Lahteine
306f0f2135
Move Stepper::synchronize to Planner ( #10713 )
...
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
2018-05-12 01:38:02 -05:00
Scott Lahteine
59fda986ea
Allow Z_AFTER_PROBING to be 0
2018-04-30 03:25:47 -05:00
Scott Lahteine
f423e54f77
Strip trailing spaces
2018-04-23 18:00:43 -05:00
Scott Lahteine
1c3d49afe0
Fix G28 with Z_AFTER_PROBING
...
Fix #10476
2018-04-22 01:23:26 -05:00
Scott Lahteine
023385ca59
Merge pull request #10479 from thinkyhead/bf2_creality_power_loss_resume
...
[2.0.x] Creality3D Power-Loss Recovery
2018-04-22 00:17:44 -05:00
Scott Lahteine
3396671011
[2.0.x] Reset LCD status to fallbacks ( #10470 )
...
* Remove obsolete strings
* Tweak some static consts
* Reset LCD status to fallbacks
2018-04-22 00:16:30 -05:00
Scott Lahteine
11ab017dd0
Creality3D Power-Loss Recovery
2018-04-21 21:56:50 -05:00
Scott Lahteine
7dcd0a1cff
Add R parameter to G28 to specify pre-raise
2018-04-21 19:07:48 -05:00
Luc Van Daele
646aa20b43
Overhaul of G33 Delta Calibration ( #8822 )
2018-04-11 21:14:48 -05:00
Luc Van Daele
ac2e0afb62
Low Point for delta calibration ( #10363 )
2018-04-11 18:59:46 -05:00
Scott Lahteine
8b8ad14178
Add Z_PROBE_LOW_POINT to prevent damage
2018-04-09 17:23:03 -05:00
Scott Lahteine
1a75165f35
For set_z_fade_height use set_bed_leveling_enabled
2018-03-31 22:43:05 -05:00
AnHardt
c1f58a238d
No delay in sensorless quick homing ( #10254 )
2018-03-29 16:10:20 -05:00
Scott Lahteine
bc45fb6b13
Tweak use of move_z_after_probing
2018-03-21 01:25:08 -05:00
Scott Lahteine
c352954882
Allow no raise after run_z_probe in probe_pt
2018-03-21 01:24:51 -05:00
Scott Lahteine
8922b56b58
Fix some spelingz
2018-03-16 01:25:41 -05:00
Scott Lahteine
a6feb58837
Delta support for multiple hotends with offsets ( #10118 )
2018-03-16 00:46:42 -05:00
Scott Lahteine
14c03cb6f4
[2.0.x] Make MIN_PROBE_EDGE a general option (for electronic probes) ( #10069 )
...
Some probes don't work near the edges of the bed. This change promotes MIN_PROBE_EDGE to a general setting that applies to all probing functions.
2018-03-13 01:15:22 -05:00
Scott Lahteine
28f1276286
[2.0.x] Add Z_AFTER_PROBING option ( #10058 )
...
Some "fix-mounted" probes need manual stowing. And after probing some may prefer to raise or lower the nozzle. This restores an old option but tailors it to allow raise or lower as preferred.
2018-03-11 13:07:55 -05:00
Scott Lahteine
751785fc97
Followup to recent patches
...
- `M666` is static, not inline
- Disambiguate some stepper macros
2018-03-10 21:41:17 -06:00
Scott Lahteine
f003173752
Fixup M666
...
Followup to d6df032
2018-03-10 19:52:30 -06:00
Scott Lahteine
d6df0322c2
Update M666 for XYZ dual endstops
2018-03-10 06:57:31 -06:00
Scott Lahteine
419d12ca1b
Add UNKNOWN_Z_NO_RAISE option
...
With this option enabled, Z won't ever be raised until after `G28` has been completed, and it won't raise if Z becomes unknown. This is good for machines whose beds fall when Z is powered off.
2018-03-10 00:17:34 -06:00
Scott Lahteine
2057177184
Make enums into implicit char
2018-03-06 23:39:56 -06:00
Scott Lahteine
a446433c87
Fix SENSORLESS_HOMING for Core Kinematics ( #9868 )
2018-03-01 01:37:31 -06:00
Scott Lahteine
b2cf253a13
Add RESTORE_LEVELING_AFTER_G28 option
2018-02-23 13:38:54 -06:00
