muele-marlin

Author	SHA1	Message	Date
Scott Lahteine	ba4a005ceb	Merge pull request #6373 from mtowara/mt_makefile_fix Fix Makefile build	2017-04-17 16:16:37 -05:00
towara	150b15c311	fix compiler errors generated by more stringent flags in Makefile: - use volatile for registers - avoid implicit casts	2017-04-17 11:59:47 +02:00
towara	f6095c9325	fix missing serial.cpp in Makefile	2017-04-17 11:59:03 +02:00
Scott Lahteine	871f92378c	Tweak headings in EEPROM structure	2017-04-16 18:42:33 -05:00
Scott Lahteine	bf2548be4a	Merge pull request #6362 from tcm0116/babystepping Only queue babysteps if axis is in a known position	2017-04-16 17:46:06 -05:00
dot-bob	9c410ddf68	Fixed an issue where a display with a hardware reset pin (LCD_RESET) may not get initialized properly.	2017-04-15 22:45:15 -06:00
Thomas Moore	72a7fac461	Only queue babysteps if axis is in a known position	2017-04-15 23:19:43 -05:00
Roxy-3D	5e9726530f	Setup to find data corruption and general clean up This data corruption problem is very difficult. Just changing the code a little bit changes whether the problem even happens and what is affected. I need these changes in the main branch so I can operate with the extra debug code always available and turned on. Everything is setup such that if M100 is turned off or DEBUG(ECHO) is turned off, the code is not affected. M100 has been made a little bit more inteligent so it can display the serial command buffers in a more meaningful way (because the data corruption seems to often times end up in that area).	2017-04-15 19:26:43 -05:00
Scott Lahteine	e519e95953	Merge pull request #6358 from thinkyhead/rc_doubleclick_fix Show Cancel/Continue screen for ABL "Level Bed"	2017-04-15 17:25:37 -05:00
Scott Lahteine	a81606c680	Show Cancel/Continue screen for ABL "Level Bed"	2017-04-15 16:51:03 -05:00
Scott Lahteine	51021bc7b8	Merge pull request #6353 from thinkyhead/rc_endstop_coolness Clean up endstop triggering code	2017-04-15 16:49:54 -05:00
Scott Lahteine	857dec0990	Merge pull request #6342 from benlye/benlye-fix-softspi Fix softspi variant conditional for 1284p	2017-04-15 16:33:50 -05:00
Scott Lahteine	4e04383d18	Merge pull request #6354 from thinkyhead/rc_doubleclick_fix Fix undefined symbol if DOUBLECLICK_FOR_Z_BABYSTEPPING and HAS_BED_PROBE defined	2017-04-15 16:06:29 -05:00
Thomas Moore	8dd0492e68	Show lcd_babystep_zoffset screen if DOUBLECLICK_FOR_Z_BABYSTEPPING is enabled and HAS_BED_PROBE is defined	2017-04-15 14:44:50 -05:00
benlye	0a2f60fab4	Make spi.h inclusion conditional spi.h is only needed if HEATER_0_USES_MAX6675 is defined, so making its inclusion conditional on HEATER_0_USES_MAX6675 being defined.	2017-04-15 16:22:42 +01:00
Bob-the-Kuhn	60471b7592	minor improvements Configuration_store.cpp - changed a couple of print statements so the values were printed. The old method resulted in the formula being printed. ubl_G29 1) added support for R option to P4. Now probes all points unless R is present and the number is greater than 0. 2) P2 - moved map print statement so it showed the point that was currently being probed, The old location did this only for the first point. 3) P4 - Moved the map print for the same reason. ultralcd.cpp - changed "Mesh Editor :" to "Mesh Editor" because the LCD draw routine puts a ":" in automatically so you end up with an extra ":" using the old message.	2017-04-15 09:31:55 -05:00
Scott Lahteine	25a61e9061	Improve motion-based endstop triggering code	2017-04-15 06:16:50 -05:00
Scott Lahteine	a2356c2825	Fix compiler warning about z-offset callback	2017-04-15 02:50:27 -05:00
Scott Lahteine	037c964d26	Reverse bools on prepare_move sub-functions	2017-04-15 01:08:19 -05:00
Scott Lahteine	d9c4333806	Extra logging of Dual X modes	2017-04-15 01:08:19 -05:00
Scott Lahteine	4067d15c92	Cleanup, extend TMC2130 implementation	2017-04-14 23:00:00 -05:00
Scott Lahteine	d60c02c5b1	Cleanup, extend TMC2130 configuration	2017-04-14 22:43:56 -05:00
Scott Lahteine	0e97b3d6d0	Fix some configuration spacing	2017-04-14 22:36:10 -05:00
Scott Lahteine	cf6f483378	Merge pull request #6187 from thinkyhead/rc_flsun_delta_autocal Delta: DELTA_HEIGHT, G33 Auto-Calibrate, drop M206/M428, add M665 H	2017-04-14 22:32:12 -05:00
Scott Lahteine	24882adfbf	Allow NO_WORKSPACE_OFFSETS with DELTA_AUTO_CALIBRATION - On `DELTA` the `M665 H` option supplants `M206` - On `DELTA` `NO_WORKSPACE_OFFSETS` only reverts `G92` behavior - Spawn 4 conditionals based on `NO_WORKSPACE_OFFSETS` - Optimize coordinate space conversion for `DELTA` workspace - To keep EEPROM version, retain `home_offset[XYZ]`, just ignore XY	2017-04-14 21:56:49 -05:00
Bob-the-Kuhn	1acb84ba02	fix 1 bug, add error messages =============================================== make changes requested by reviewers =============================================== add M43 test to Travis, fix EOL, remove trailing spaces	2017-04-14 20:57:45 -05:00
LVD-AC	8821963873	Implement delta auto-calibration and delta_height	2017-04-14 19:46:31 -05:00
Scott Lahteine	b305699046	Merge pull request #6341 from benlye/benlye-lcd_babystep_zoffset Fix lcd_babystep_zoffset()	2017-04-14 19:11:46 -05:00
LVD-AC	03bda24d19	Add delta auto-calibration and configuration for Flsun AC	2017-04-14 19:08:14 -05:00
Scott Lahteine	1bd25fd2b3	Clean up config spacing, section headings, etc.	2017-04-14 19:06:31 -05:00
Scott Lahteine	153b0ae967	Tweak Delta Printer configuration note	2017-04-14 19:06:06 -05:00
Scott Lahteine	81ffd98dd9	Allow faux leveling	2017-04-14 19:06:06 -05:00
Scott Lahteine	2355d87e11	Merge pull request #6346 from thinkyhead/rc_broken_abl_test Add support for SOLENOID_PROBE	2017-04-14 18:36:32 -05:00
Scott Lahteine	f4685c28b7	Reorder Conditionals_post.h and add comments	2017-04-14 18:18:21 -05:00
Scott Lahteine	0ac2b5c045	Additional 5 extruders support (solenoids, microstepping)	2017-04-14 18:18:20 -05:00
Scott Lahteine	fd2a0784ba	Add support for SOLENOID_PROBE	2017-04-14 17:24:36 -05:00
Scott Lahteine	5803ba43a9	Expose EXT_SOLENOID as an advanced option	2017-04-14 17:24:36 -05:00
Scott Lahteine	ea734f910b	Use direct pin manipulation whenever possible	2017-04-14 16:55:35 -05:00
Scott Lahteine	19d0c6a0c0	Patch to init W with RGBW_LED	2017-04-14 16:55:23 -05:00
Scott Lahteine	3e079660b0	Never define SLED_PIN	2017-04-14 16:36:32 -05:00
benlye	1a447d0047	Fix variant conditional for 1284p	2017-04-14 18:46:09 +01:00
benlye	1f9ee42750	Fix lcd_babystep_zoffset() Resolve 'steps_to_mm was not declared in this scope' compilation error after recent changes to merge babystepping with M851	2017-04-14 18:38:35 +01:00
Bob-the-Kuhn	445d39e95a	CORExx endstop detection fixes 1. The CORExx printers were checking more endstop axis than needed. 2. Removed all the CORE_xx_NOT logic. The motor_direction(xx) routine always returns the correct data so it is not needed. It was actually cause the wrong direction to be checked in some cases. 3. Made the logic/defines for X, Y & Z axis all the same. The old logic checked inappropriate configurations for Y and didn't check all the correct configurations on Z. 4. Added a check for zero steps before the X, Y & Z axis. Previously would check the they axis even if there were no movement.	2017-04-13 21:43:37 -05:00
Roxy-3D	28fec61f92	M100 Fixes and Features All the memory accesses need to be unsigned char in order to avoid false errors being detected. Two new features are available for developers to call into the M100 functionality to look for data corruption.	2017-04-13 18:20:53 -05:00
Scott Lahteine	52c3ace102	Add BABYSTEP_ZPROBE_OFFSET as an optional feature	2017-04-13 16:29:43 -05:00
Scott Lahteine	cd4e6abec8	Group BABYSTEPPING options together	2017-04-13 16:26:45 -05:00
Scott Lahteine	60ac41a32c	Add code to handle changes to zprobe_zoffset	2017-04-13 15:46:35 -05:00
Scott Lahteine	8fa4209916	Movement/adjustment should be reverse of probe offset change	2017-04-13 15:46:05 -05:00
Thomas Moore	361655828f	Use babystepping to adjust bed probe z-offset	2017-04-13 15:46:05 -05:00
Scott Lahteine	36e5c7c389	Merge pull request #6330 from thinkyhead/rc_improvements Sanity check per-axis options' array sizes	2017-04-13 13:08:44 -05:00
Scott Lahteine	02fca543bb	Merge pull request #6272 from thinkyhead/rc_adc_variable_rate Make ADC sensor reading frequency adjustable	2017-04-13 12:49:31 -05:00
Scott Lahteine	34308368c0	Sanity check per-axis settings for size	2017-04-13 11:35:20 -05:00
Scott Lahteine	ac96ae89f9	Apply `const` in Stepper::isr	2017-04-13 06:20:36 -05:00
Scott Lahteine	2fa1e882d0	Merge pull request #6325 from thinkyhead/rc_M20_with_size Simplified M20 with size	2017-04-13 05:06:52 -05:00
Bob-the-Kuhn	1b12fea0fa	simplified M20 with size	2017-04-13 04:56:58 -05:00
Scott Lahteine	4022b971db	Merge pull request #6315 from thinkyhead/rc_unify_M421 Unify M421	2017-04-12 19:43:28 -05:00
Scott Lahteine	b236562354	Merge pull request #6306 from thinkyhead/cleanup_after_6302 Adjustments to M100	2017-04-12 19:12:27 -05:00
Scott Lahteine	5e4f4d387f	Swap MBL z_values dimensions to [X][Y]	2017-04-12 17:24:05 -05:00
Scott Lahteine	063f641651	Unify M421	2017-04-11 15:46:13 -05:00
Scott Lahteine	6d5400dc31	Merge pull request #6240 from thinkyhead/rebuild_rgb_led Extend RGB LED with Printer Events	2017-04-11 15:16:57 -05:00
Scott Lahteine	dac21ec680	Add support for an RGBW LED	2017-04-11 12:58:55 -05:00
Scott Lahteine	e7746ffee4	Extend RGB LED support, adding Printer Events	2017-04-11 12:15:41 -05:00
Scott Lahteine	c7063eb55c	theTarget => target_temp	2017-04-11 12:15:41 -05:00
Scott Lahteine	36bda2bade	Add HAS_RESUME_CONTINUE shorthand macro	2017-04-11 12:15:40 -05:00
Scott Lahteine	53e6c33c37	2 is DXC_DUPLICATION_MODE	2017-04-11 12:15:40 -05:00
Scott Lahteine	a2cb0a3d54	Use multiply for delta probe constraint	2017-04-11 12:15:40 -05:00
Scott Lahteine	6487c96a4a	Merge pull request #6313 from Kaibob2/patch-10 Allow 10mm Movements for Z-Axis	2017-04-11 12:04:10 -05:00
Kai	001bc14255	Allow 10mm Movements for Z-Axis I use the movement options via LCD quite often. Especially to get the nozzle out of the way. I see no reason, why the 10mm option is disabled for the Z-Axis, this is why i always delete this line when i compile a new version. If this is unwanted, please just close this PR	2017-04-11 18:39:26 +02:00
Scott Lahteine	6a9b008044	Fix MINIMUM_STEPPER_PULSE maths	2017-04-11 11:11:17 -05:00
Scott Lahteine	68773f4486	Simplify stepper macros by renaming enable/disable macros	2017-04-11 11:10:26 -05:00
Scott Lahteine	e02a5a6371	Add macros for delays by machine cycle	2017-04-11 09:18:32 -05:00
Scott Lahteine	ecc537015a	Have M109 / M190 do nothing with no parameters	2017-04-11 05:06:25 -05:00
Scott Lahteine	03aa9a390e	Apply coding standards to M100, break up into functions	2017-04-10 21:09:43 -05:00
Scott Lahteine	48c16fc6ef	Merge pull request #6307 from thinkyhead/rc_less_no_reentrance Only lcd_synchronize needs no_reentry	2017-04-10 20:58:32 -05:00
Scott Lahteine	4fcfe926d6	Only lcd_synchronize needs no_reentry	2017-04-10 20:13:23 -05:00
Scott Lahteine	67fb7f82ac	Merge pull request #6283 from thinkyhead/rc_eeprom_z_fade Save / restore z_fade_height in EEPROM	2017-04-10 20:05:20 -05:00
Scott Lahteine	eff5af569b	Merge pull request #6300 from MagoKimbra/rc_fix_mesh_report Fix mbl_mesh_report	2017-04-10 19:37:19 -05:00
Scott Lahteine	4a18968c10	Merge pull request #6297 from Kaibob2/patch-9 Fix EPROM -> EEPROM	2017-04-10 19:35:30 -05:00
Roxy-3D	ba85faabc0	Fix M100 Free Memory Checker M100 had numerious changes and quit working. Part of the problem is the overloading of the SERIAL_PROTOCOL functions. Also, some of the address arithmatic was changed to use char *ptr and passing ptr into the SERIAL_PROTOCOL functions caused them to try to print a string instead of a number. M100 is working again. Let's keep it that way! M100 has been expanded to now have a function int free_memory_is_corrupted() that can be called from other code to see if the free space is still contiguous. It may make sense to add a flag to control its verbose nature but right now, the extra chit chat is very helpful to know int free_memory_is_corrupted() is doing the right thing and what it found at various points when it was called. A 'Show & Tell' is coming up with int free_memory_is_corrupted().	2017-04-10 15:33:55 -05:00
Kai	3b82db5fe9	Missing semicolon in ultralcd.cpp When PARK_HEAD_ON_PAUSE is defined Marlin won't compile because of two missing semicolon.	2017-04-10 14:45:51 -05:00
MagoKimbra	7d2e637867	Fix mbl_mesh_report	2017-04-10 20:50:19 +02:00
Kai	afeb0452ef	Fix EPROM -> EEPROM These fixes are neede because before it showed the englisch text even if language = de was selected	2017-04-10 18:37:00 +02:00
Scott Lahteine	7f950a80c0	Make ADC sensor reading frequency adjustable	2017-04-09 22:18:21 -05:00
Scott Lahteine	786af73e24	Convert config code to a static class	2017-04-09 22:06:41 -05:00
james94jeans2	5b9476fe78	Added z_fade_height to EEPROM-Settings Firmware was forgetting the z_fade_height in Planner, set by M420 Z<f>, after each reset or loading settings from EEPROM. Added the float z_fade_height to EEPROM-Storage, now remembers the value.	2017-04-09 21:16:58 -05:00
Scott Lahteine	9343f6a95f	Put TOSHIBA with other stepper driver options	2017-04-09 20:52:49 -05:00
Scott Lahteine	7a704af5e6	Merge pull request #6284 from thinkyhead/rc_wt150_rebase wt150 (Mightyboard Rev E) & RRD Full Graphic Smart Controller	2017-04-09 20:27:44 -05:00
Max Matveev	2031fb913b	Fixed comparison of float values to NaN	2017-04-09 20:28:46 +02:00
Scott Lahteine	e48a52a530	Patch a display issue with LCD_DECIMAL_SMALL_XY The `ftostr4sign` function got munged by the `WITHIN` patch	2017-04-09 10:25:35 -05:00
Scott Lahteine	1a3cd6a090	Merge pull request #6213 from thinkyhead/rc_gitattributes Init bed_level_virt_interpolate on EEPROM load	2017-04-09 08:13:11 -05:00
Scott Lahteine	314a02e2d5	Toggle with XOR	2017-04-09 07:58:47 -05:00
Scott Lahteine	8bc0d90b00	Init bed_level_virt_interpolate on EEPROM load	2017-04-09 07:04:20 -05:00
MD	20dd5376b8	Cheaptronic V2 Add support for new electronics www.reprapobchod.cz	2017-04-09 06:57:43 -05:00
Scott Lahteine	4cdda5615b	Bring other configs up to date with wt150 changes	2017-04-09 06:45:42 -05:00
Paweł Stawicki	9b0885f4f6	Allow boards without a thermistor	2017-04-09 06:45:41 -05:00
Paweł Stawicki	64cfcebe66	Update SlowSoftI2CMaster link. MightyBoard digipots I2C bus has no resistors.	2017-04-09 06:45:03 -05:00
Paweł Stawicki	0eb16d9ff7	Add example config for the wt150 printer with RepRapDiscount Full Graphic Smart Controller	2017-04-09 06:44:54 -05:00
Paweł Stawicki	652bedfa18	Add RepRapDiscount Full Graphic Smart Controller support to MIGHTYBOARD REVE	2017-04-09 06:44:53 -05:00
Paweł Stawicki	44cdebb8f1	Add software spi support for max6675	2017-04-09 06:44:53 -05:00
Paweł Stawicki	191fec009f	Add digipot i2c control for MCP4018	2017-04-09 06:44:53 -05:00
Scott Lahteine	e5b16081cb	Update TinyBoy2 configurations	2017-04-09 06:44:53 -05:00
Scott Lahteine	1855534f20	Config files cleanup	2017-04-09 06:44:52 -05:00
Scott Lahteine	c26a315d0b	Additional missed patches	2017-04-09 04:24:23 -05:00
Scott Lahteine	39617e10b8	Patch configs comment formatting	2017-04-09 03:49:16 -05:00
Scott Lahteine	c54f6cf23d	Updates to support 5 extruders	2017-04-09 03:49:16 -05:00
Scott Lahteine	2b88ccd0aa	Apply UBL mesh bounds to remaining configs	2017-04-09 03:49:15 -05:00
Scott Lahteine	60be3d264b	Macros to print floats, hiding imprecision	2017-04-09 03:48:40 -05:00
Scott Lahteine	b356d73239	Merge pull request #6278 from thinkyhead/pr_delta_angles Followup to additional delta trim options	2017-04-08 22:25:57 -05:00
Jimmy Envall	f78d44e91a	Added support for delta tower angle corrections.	2017-04-08 21:13:44 -05:00
Scott Lahteine	d3b4d84586	Merge pull request #6277 from thinkyhead/pr_roxy3d_rcbugfix Unify UBL Command Parsing	2017-04-08 20:17:46 -05:00
Scott Lahteine	d4ce839351	Cleanup following Pins Debug update	2017-04-08 18:59:57 -05:00
Scott Lahteine	c7a8f7970b	Formatting / cleanup	2017-04-08 18:59:57 -05:00
Scott Lahteine	29d4ec8257	Support 5 extruder auto fans	2017-04-08 18:59:57 -05:00
Scott Lahteine	824f3c1c0d	Fix up configuration comments	2017-04-08 18:59:56 -05:00
Scott Lahteine	995ed90248	Clean up Filament Width Sensor comments	2017-04-08 18:59:56 -05:00
Scott Lahteine	5a7b810fdd	General comment cleanup	2017-04-08 18:58:33 -05:00
Scott Lahteine	0027c22839	Drop extraneous calls to lcd_update	2017-04-08 18:58:33 -05:00
Scott Lahteine	d6db7a9b03	patch "step_remaining"	2017-04-08 18:13:20 -05:00
Scott Lahteine	cbc2331187	Use LCD_MESSAGEPGM over lcd_setstatuspgm	2017-04-08 18:04:39 -05:00
Scott Lahteine	3729510b1e	Set and check main parameter values, report all errors	2017-04-08 17:15:55 -05:00
Roxy-3D	34d3ed9ab1	These items were removed from the UBL Command Parsing Having these items randomly (and errorniously) disappear cost me several hours of work yesterday.	2017-04-08 15:30:20 -05:00
Scott Lahteine	15edb41cee	Patches to UBL	2017-04-08 14:59:14 -05:00
Roxy-3D	14cf527bb8	Getting setup for debugging	2017-04-08 14:59:14 -05:00
Scott Lahteine	f8408036f2	Merge pull request #6264 from thinkyhead/rc_five_extruders Support up to 5 extruders in Marlin	2017-04-07 12:48:56 -05:00
Bob-the-Kuhn	f7fc49c3a3	Finish name change DAC_STEPPER_DFLT wasn't changed to DAC_MOTOR_CURRENT_DEFAULT in all places on PR #6124	2017-04-07 11:05:24 -05:00
Scott Lahteine	832064e4f2	Implementation changes to support 5 extruders	2017-04-07 10:46:37 -05:00
Scott Lahteine	04050237f0	Header and pins changes to support 5 extruders	2017-04-07 10:46:36 -05:00
Scott Lahteine	2a84122edd	Configuration changes to support 5 extruders	2017-04-07 10:46:35 -05:00
Scott Lahteine	edf18977c1	Patch pins files hotends/e-steppers sanity check	2017-04-07 10:46:33 -05:00
Scott Lahteine	dc84678fc1	Fix HOTEND_STATUS_ITEM for graphical display	2017-04-06 23:07:30 -05:00
Scott Lahteine	a0de5d94e2	Merge pull request #6258 from benlye/benlye-bilinearfix2 Better fix for bilinear Z offset and G29 Z (update to #6251)	2017-04-06 20:51:57 -05:00
Scott Lahteine	b23aef5b8d	Merge pull request #6190 from Bob-the-Kuhn/Stop-and-Kill-prints---round-2 Message for every KILL and STOP (also need delays)	2017-04-06 20:40:12 -05:00
Roxy-3D	945303c0d5	eleminate bootscreen.h	2017-04-06 19:55:41 -05:00
Roxy-3D	ef3da3971e	Update ubl.h	2017-04-06 19:55:41 -05:00
Roxy-3D	8644dc170b	get synchronized to current file names	2017-04-06 19:55:41 -05:00
Roxy-3D	1451b7eacf	UBL's Grid Based Leveling code Pretty much... The code is in place. Still more work to do. But it has a lot of hooks and variables in other code, so commit and merge before I pick up a million 'Conflicts'.	2017-04-06 19:55:41 -05:00
Bob-the-Kuhn	549055f20c	Merge pull request #6124 from Bob-the-Kuhn/MCP4728-consistency MCP4728 consistency & fix ultralcd.cpp (PRINTRBOARD Rev F and RIGIDBOARD V2)	2017-04-06 16:35:50 -05:00
Bob-the-Kuhn	a77875c9d2	Merge pull request #6114 from Bob-the-Kuhn/try2-add-BLTouch-retry Another BLTouch retry place (replaces PR #6108)	2017-04-06 16:25:55 -05:00
Bob-the-Kuhn	3b9ff2cb12	Merge pull request #5676 from Bob-the-Kuhn/configuration.h Configuration.h - reword Z PROBE section	2017-04-06 16:18:34 -05:00
Bob-the-Kuhn	6643d553f6	# This is a combination of 2 commits. # This is the 1st commit message: MCP4728 consistency & fix ultralcd.cpp The MCP4728 DAC controls the stepper motor current strenth on the PRINTRBOARD Rev F and RIGIDBOARD V2 boards. PR #5792 on 9 FEB 2017 implemented default drive percentages but only on the RIGIDBOARD V2. This change moves the default settings to Configuration_adv.h. Also, ultralcd.cpp won't compile because of a type def conflict. Changed it to match the one in stepper_dac.cpp =========================================================== reword stepper curent section for clarity =========================================================== change name & improve comments =========================================================== changed name from A4JP to SCOOVO_X9H per PR #6139 # This is the commit message #2: fix typo	2017-04-06 16:16:27 -05:00
Bob-the-Kuhn	a44b3432c1	add BLTouch retry to a second place & add/update delays ================================================= implement requested changes ================================================= remove delays (they're in another PR) & move return	2017-04-06 16:13:07 -05:00
Bob-the-Kuhn	a5abc61fb9	Merge pull request #6219 from Bob-the-Kuhn/Servo-probe-and-toggle-pins M43 - add Toggle utility and Z servo utility (replaces PR #5864)	2017-04-06 16:10:50 -05:00
Bob-the-Kuhn	3b8926bd09	improved wording, consolidation of info, BLTouch warning ============================================== clarified BLTouch calculation & changed comment delimitters/flags I found it hard to pickout the various sections in this area so I changed most comments from // style to /** ... */ Made the BLTouch calculation simpler and clarified the units of measure for the result. ============================================ add changes to example configurations ============================================ add TinyBoy2 to this PR & add BLTouch Delay	2017-04-06 16:06:01 -05:00
Scott Lahteine	55d296aaf0	pinsDebug with more features, uses less RAM I've just uploaded a major change to pinsDebug. The big change was creating an array in FLASH that contained every active pin definition. That reduced the RAM memory usage considerably but increased the FLASH usage. Creating the array requires going through the pin list twice. Rather than having two copies of it in the code I moved the list out to another file (pinsDebug_list.h) and then just did two #includes. From the user’s view they’ll see the following changes: 1. Now reports all the names assigned to a pin 2. The port is now reported in addition to the pin number. 3. When PWM0A & PWM1C share a pin, both PWMs are reported 4. More PWM/Timer info is reported One new item that may cause some concern is the usage of the LINE predefined preprocessor macro. It may not be available if the Arduino IDE goes to a different compiler. Includes support for 1284 & 1286 families. Memory usage changes when enabling PINS_DEBUGGING: ATmega2560 FLASH . without 52576 . with new 64592 . with old 62826 . new-out 12016 . old-out 10250 . new-old 1766 . RAM . without 2807 . with new 2875 . with old 3545 . new-out 68 . old-out 738 . new-old -670 ================================================================== minor changes - mostly formatting 1) added newline to end of teensyduino file 2) changed flag name from TEENSYDUINO to TEENSYDUINO_IDE. Got warnings about redefining TEENSYDUINO 3) removed some trailing spaces reduce PROGMEM size & update pin list Reduced PROGMEM usage by 1) converting often used macro to a function 2) moved as much as possible into the function This required creating two arrays of address pointers for the PWM registers. ================================================================== update with new M3, M4, M5 pin names ================================================================== report I/O status for unused/unknown pins	2017-04-06 16:06:01 -05:00
Scott Lahteine	e116723b8b	Adjust indentation in ubl.h	2017-04-06 16:06:00 -05:00
Scott Lahteine	1b3a26f2f5	Rename all UBL files with a ubl_ prefix	2017-04-06 16:06:00 -05:00
Scott Lahteine	d13991ae18	Use same config name for all mesh dimensions	2017-04-06 16:05:59 -05:00
Bob-the-Kuhn	f9686a108c	add Z servo test and toggle pins to M43	2017-04-06 15:59:38 -05:00
Scott Lahteine	62cbaa302e	Z_DUAL_ENDSTOP - make offset a configuration item The offset for Z_DUAL_ENDSTOP (z_endstop_adj) is already in Marlin. This PR just makes it a configuration item. z_endstop_adj is initialized in two places so both had to be modified.	2017-04-06 15:57:10 -05:00
Scott Lahteine	c9e35004e7	pinsDebug with more features, uses less RAM I've just uploaded a major change to pinsDebug. The big change was creating an array in FLASH that contained every active pin definition. That reduced the RAM memory usage considerably but increased the FLASH usage. Creating the array requires going through the pin list twice. Rather than having two copies of it in the code I moved the list out to another file (pinsDebug_list.h) and then just did two #includes. From the user’s view they’ll see the following changes: 1. Now reports all the names assigned to a pin 2. The port is now reported in addition to the pin number. 3. When PWM0A & PWM1C share a pin, both PWMs are reported 4. More PWM/Timer info is reported One new item that may cause some concern is the usage of the LINE predefined preprocessor macro. It may not be available if the Arduino IDE goes to a different compiler. Includes support for 1284 & 1286 families. Memory usage changes when enabling PINS_DEBUGGING: ATmega2560 FLASH . without 52576 . with new 64592 . with old 62826 . new-out 12016 . old-out 10250 . new-old 1766 . RAM . without 2807 . with new 2875 . with old 3545 . new-out 68 . old-out 738 . new-old -670 ================================================================== minor changes - mostly formatting 1) added newline to end of teensyduino file 2) changed flag name from TEENSYDUINO to TEENSYDUINO_IDE. Got warnings about redefining TEENSYDUINO 3) removed some trailing spaces reduce PROGMEM size & update pin list Reduced PROGMEM usage by 1) converting often used macro to a function 2) moved as much as possible into the function This required creating two arrays of address pointers for the PWM registers. ================================================================== update with new M3, M4, M5 pin names ================================================================== report I/O status for unused/unknown pins	2017-04-06 14:46:28 -05:00
Scott Lahteine	4abd53f65a	Adjust indentation in ubl.h	2017-04-06 05:36:16 -05:00
Scott Lahteine	f5c5c1f771	Rename all UBL files with a ubl_ prefix	2017-04-06 05:33:27 -05:00
benlye	f1d50ac1dc	Fixing bilinear Z offset and G29 Z The fix in #6251 for bilinear Z offset was flawed and broke the Z parameter of G29 for bilinear levelling. This is reverted and a different fix is used for the double-addition of the Z-probe offset to the bilinear correction grid.	2017-04-06 07:41:46 +01:00
Scott Lahteine	eb1e6aa29b	Use same config name for all mesh dimensions	2017-04-06 00:42:52 -05:00
Scott Lahteine	c961dd084d	Add hidden option to output Bilinear grids in JSON	2017-04-05 23:43:17 -05:00
Scott Lahteine	df7b4252fd	Reduce M420 code for UBL slightly	2017-04-05 22:30:29 -05:00
Scott Lahteine	8866158d03	Add LEVELING_DATA as a capability	2017-04-05 22:30:28 -05:00
benlye	0a2b4f3486	Fix bilinear levelling z offset Since run_probe was altered to return the probe Z position rather than the nozzle Z position bilinear levelling has been broken because the Z-offset has been applied twice - once in the run_probe function, and then again in the G29 code for bilinear levelling.	2017-04-05 22:01:40 -05:00
Scott Lahteine	44a849bdce	Fix broken M206/M428/G92 offsets	2017-04-05 22:01:37 -05:00
Roxy-3D	52978e5ba5	Fix spelling mistake when UBL's mesh is Inactive	2017-04-02 20:07:09 -05:00
Roxy-3D	0423e93c42	Fix M421 AUTO_BED_LEVELING_BILINEAR and AUTO_BED_LEVELING_UBL M421 was not connected up for AUTO_BED_LEVELING_BILINEAR. M421 needed to migrate mesh data to new UBL EEPROM layout.	2017-04-02 16:46:37 -05:00
Scott Lahteine	3412950abc	Merge pull request #6209 from thinkyhead/rc_psu_zero Power Supply 0 as "General"	2017-04-02 16:44:42 -05:00
Roxy-3D	3e9e94801f	Fix problem described in issue # 6175 As it turns out... an unsigned int can not go to less than 0, so the loop never terminates.	2017-04-02 13:00:27 -05:00
Scott Lahteine	289e3d6844	Merge pull request #6215 from thinkyhead/rc_bed_false_alarm Fix thermal runaway when nonexistent bed temp is set	2017-04-02 11:59:58 -05:00
Scott Lahteine	948728e63b	Fix line-endings in UBL_G29	2017-04-02 11:48:26 -05:00
Scott Lahteine	699310d1d2	Fix: Thermal runaway if nonexistent bed's temp is set	2017-04-02 11:48:10 -05:00
Scott Lahteine	c56eec29f0	Configurable delay for BLTouch servo emulation	2017-04-02 11:14:53 -05:00
Scott Lahteine	deaad78df9	Merge pull request #5678 from Bob-the-Kuhn/G38-optional-double-tap G38 bug fix, made double touch optional & reverted to Z_MIN_PROBE	2017-04-02 10:32:04 -05:00
Scott Lahteine	5bce731962	Fix LCD preheat menus	2017-04-02 09:32:22 -05:00
Scott Lahteine	4c72167af3	Prevent a warning on echo_command	2017-04-02 08:36:58 -05:00
Scott Lahteine	9b5fd9522e	Fix formatting, order for a UBL change	2017-04-02 07:15:40 -05:00
Tannoo	54173c80ad	Power Supply 0 as "General"	2017-04-02 06:21:34 -05:00
Scott Lahteine	a2775d0c70	can wstring be removed?	2017-04-02 04:43:33 -05:00
Scott Lahteine	de4e19f17e	Patch MarlinSerial to match up with 32-bit version	2017-04-02 04:39:18 -05:00
Scott Lahteine	2cbc7b4b73	Relocate serial macros and functions	2017-04-02 01:05:25 -05:00
Scott Lahteine	eaa66f3c46	Indent MarlinSerial code	2017-04-02 01:05:25 -05:00
Scott Lahteine	7a7a80e6c5	status_printf => lcd_status_printf_P	2017-04-02 01:05:25 -05:00
Scott Lahteine	0e6ec34228	Use PSTR versions of lcd_status... to save SRAM	2017-04-02 00:45:39 -05:00
Scott Lahteine	34e2420b9b	Apply const args, clean up find_closest_circle_to_print	2017-04-01 23:15:41 -05:00
Scott Lahteine	e19fbd27ce	Minor spelling patch	2017-04-01 23:08:00 -05:00
Scott Lahteine	790a3e9a8c	Remove extraneous check of UBL_G26_MESH_EDITING	2017-04-01 23:03:40 -05:00
Scott Lahteine	7310110ec0	Fix logic of UBL::fade_scaling_factor_for_z	2017-04-01 22:52:48 -05:00
Scott Lahteine	1a775cecac	Revert behavior of enqueue_and_echo_commands_P	2017-04-01 21:53:46 -05:00
Scott Lahteine	79d42d87c1	Syntax cleanup	2017-04-01 21:53:46 -05:00
Scott Lahteine	b47fd31c37	Revert some changes to UBL	2017-04-01 21:53:45 -05:00
Bob-the-Kuhn	185337e787	add delays to allow stop & kill messages to get out	2017-04-01 00:23:14 -05:00
Scott Lahteine	63abb65146	Update description of PINS_DEBUGGING	2017-03-31 18:57:48 -05:00
Scott Lahteine	73e193da1d	Implement LCD_BED_LEVELING for PROBE_MANUALLY	2017-03-31 11:50:18 -05:00
Scott Lahteine	fcadc7bb1a	Implement the "manual" option for ABL	2017-03-31 11:50:18 -05:00
Scott Lahteine	9e22184936	Add a "manual" option for ABL	2017-03-31 11:50:18 -05:00
Scott Lahteine	541165e878	Merge pull request #6181 from thinkyhead/rc_ubl_further_fixes Further adjustments to UBL code	2017-03-31 11:35:02 -05:00
Scott Lahteine	b19a15fa7f	Within applied to UBL	2017-03-31 11:12:57 -05:00
Scott Lahteine	342ee458ae	Additional UBL fixes, optimizations	2017-03-31 11:12:57 -05:00
Scott Lahteine	a5e085cbea	Have run_probe() return probe Z, not nozzle Z	2017-03-31 09:27:49 -05:00
Scott Lahteine	4487d22d56	Apply FIXFLOAT macro	2017-03-31 09:27:48 -05:00
Scott Lahteine	6cac0f43eb	MBL fiddle	2017-03-31 09:27:48 -05:00
Scott Lahteine	25a6bfa7ed	Add and apply WITHIN macro	2017-03-31 09:27:48 -05:00
Scott Lahteine	81136c1e82	Merge pull request #6177 from thinkyhead/rc_tinyboy Support for TinyBoy 2 3D printer (and its OLED display)	2017-03-31 04:31:47 -05:00
Scott Lahteine	93aad54dc1	Clean up code, remove _now command function	2017-03-31 04:17:31 -05:00
Stefan Brüns	6ba6c92a81	Add example configuration for TinyBoy L10/L16 The TB2 is a Indiegogo funded 3d printer. It uses a MKS SMELZI V1.0 main board (based on MELZI, i.e. Sanguinololu). I comes as a complete kit, including display and panel. Two variants exists, L10 and L16, with a height of 100 and 160 mm. The heating function of the provided bed can enabled by soldering a thermistor and some wires to it. Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>	2017-03-31 04:05:35 -05:00
Stefan Brüns	0fe57ad4f5	Add Support TinyBoy2 OLED/Encoder panel The OLED is driven by an SSD1306, connected to the board via I2C, the rotary encoder is connected to 3 GPIO pins. Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>	2017-03-31 04:05:34 -05:00
Scott Lahteine	65ca6472ba	Make G26 compatible with G92 and M206	2017-03-31 02:20:20 -05:00
Scott Lahteine	4902fd4e95	More data in UBL class, make it a static class - Make all `unified_bed_leveling` data/methods static - Move some UBL-related variables into the class - Replace `map_[xy]_index_to_bed_location` with `mesh_index_to_[xy]pos`	2017-03-31 02:20:20 -05:00
Scott Lahteine	edbc024d76	Disable UBL_G26_MESH_EDITING by default	2017-03-31 02:20:20 -05:00
Scott Lahteine	9e4bd6b3b5	Further repairs to UBL, comments, spacing	2017-03-31 02:20:20 -05:00
Bob-the-Kuhn	f3618c3337	Reduce UBL RAM usage by making G26/G29 optional	2017-03-31 02:20:19 -05:00
Scott Lahteine	c9eb1d6ab7	Make MBL a static class, use lookup for index-to-point conversion	2017-03-31 01:28:07 -05:00
Scott Lahteine	de9d2cddc3	Merge pull request #6152 from thinkyhead/rc_cleanup_6150_etc UBL cleanup, optimization	2017-03-30 17:40:29 -05:00
Scott Lahteine	9217e4b8ec	Various UBL cleanups and bug fixes	2017-03-30 17:09:49 -05:00
Scott Lahteine	9924199802	Merge pull request #5908 from thinkyhead/rc_fix_slowdown General minor cleanup	2017-03-29 21:43:33 -05:00
Scott Lahteine	0e71e7b2fb	Cleanup to planner.cpp	2017-03-29 06:48:07 -05:00
Scott Lahteine	f105cad43c	Marlin: Slight cleanup to Marlin_main.cpp	2017-03-29 06:40:29 -05:00
Scott Lahteine	499f9e04e1	Marlin: Temperature soft-PWM cleanup	2017-03-29 06:37:27 -05:00
Scott Lahteine	7ddd94dc61	Merge pull request #5994 from StefanBruens/fix_Makefile_errors Fix makefile errors, cleanup	2017-03-29 06:32:08 -05:00
Scott Lahteine	af09095f03	Merge pull request #6154 from thinkyhead/rc_fil_sensor_vs_sd Show Filament Width on LCD when SD is disabled	2017-03-29 05:24:48 -05:00
Remo Kallio	d38b1bc4b1	Show filament width sensor values in LCD constantly if SD card support is not enabled.	2017-03-29 04:03:08 -05:00
Scott Lahteine	e3459ec178	Merge pull request #5989 from MagoKimbra/rc_fix_delta_angles Fix delta_angles	2017-03-29 03:35:18 -05:00
Scott Lahteine	f49aec057f	Tweak "can not" => "can't" in RUMBA pins	2017-03-29 01:04:50 -05:00
Scott Lahteine	0a23a1bb3b	Dynamic feedrate on SCARA, converting target mm/s to deg/s	2017-03-28 17:21:07 -05:00
Roxy-3D	d8724bb546	Get G29's P1 (Automated Probing) working again. Incorrect optimizations of data types and ternary operators caused some issues.	2017-03-28 17:11:02 -05:00
Scott Lahteine	c7f6ee9c93	Board A4JP should be SCOOVO_X9H	2017-03-27 22:22:13 -05:00
Scott Lahteine	a9fc30ae2e	Use safe_delay to ensure watchdog reset	2017-03-26 23:49:56 -05:00
Roxy-3D	171904b6c7	Make G29 What command print reliably and fix G29 P1 bug Waldo found	2017-03-26 17:05:58 -05:00
Roxy-3D	9d3ac66f73	Map clean up of UBL UBL's maps are cleaner. And with a 1 value, G29 O 1 will generate a map suitable to be Cut & Pasted into Excel so a Suface Map can be generated.	2017-03-25 18:55:05 -05:00
Roxy-3D	9a1949a91e	Cleaned up G26 ready to replace existing one at MarlinFirmware/Marlin	2017-03-25 10:15:40 -05:00
Roxy-3D	aec85ad45a	Start of process to get UBL running again. The wait_for_user change totally broke UBL. But there is stuff wrong now in the thermal code and/or LCD Panel code.	2017-03-24 18:38:27 -05:00
Scott Lahteine	b47eaf14ae	Merge pull request #6109 from thinkyhead/rc_soft_pwm_dither PWM dithering followup	2017-03-24 18:21:07 -05:00
Scott Lahteine	34d1c41b5f	Merge pull request #6111 from benlye/benlye-patch-echo_command Fix type conversion issue with echo_command	2017-03-24 17:57:28 -05:00
benlye	6a601aca35	Fix type conversion issue with echo_command With the the current definition of echo_command I cannot compile RCBugFix (Arduino IDE 1.8.1) with the error "invalid conversion from 'const char' to 'char'". This change resolves that.	2017-03-24 17:23:02 +00:00
Scott Lahteine	009a6ddd39	Adjust bilinear grid in M851	2017-03-24 06:28:59 -05:00
Scott Lahteine	eab7854a73	Merge pull request #6074 from thinkyhead/rc_immediate_shove Immediate commands take precedence	2017-03-24 05:52:27 -05:00
Stefan BrÃ¼ns	5699e2b881	Add SOFT_PWM_DITHER to other configurations	2017-03-24 05:02:24 -05:00
Scott Lahteine	5a2abeca78	Merge pull request #6100 from thinkyhead/rc_soft_pwm_dither Enhancement of PWM, with dithering	2017-03-24 04:57:40 -05:00
Scott Lahteine	043be2856b	Use "& 0x3F" instead of "% 64"	2017-03-24 04:13:50 -05:00
Stefan Brüns	6a040a6967	SOFT_PWM: Do not switch off heaters twice on pwm_count wraparound After wraparound, pwm_count <= pwm_mask holds, thus soft_pwm_X <= pwm_count guarantees soft_pwm_X < pwm_mask is true, and the heater will be switched off in the first branch. Do not evaluate the pwm conditions a second time, this reduces the instruction count (4 instructions per PWM) and text size (6 byte). Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>	2017-03-24 04:13:50 -05:00
Stefan Brüns	0a74774af1	soft_pwm: avoid useless refetches of pwm_count The compiler is not able to reuse the value of pwm_count, but reloads it on every evaluation, if is stored in a static variable, as it cannot prove it will be unchanged. A variable with local scope may not be modified from the outside, so its value can be reused. Doing so reduces text size and instruction count. Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>	2017-03-24 04:13:50 -05:00
Stefan BrÃ¼ns	35a55d5757	SOFT_PWM: Implement dithering if SOFT_PWM_SCALE is 1 or more If dithering is enabled, the remainder of the soft_pwm_X duty value at turnoff time is added to the next cycle. If e.g. the duty is set to 9 and SCALE is set to 2, the PWM will be active for 8 counts for 3 cycles and 12 counts on each fourth cycle, i.e. the average is 9 cycles. This compensates the resolution loss at higher scales and allows running fans with SOFT_PWM with significantly reduced noise. Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>	2017-03-24 04:13:36 -05:00
Stefan Brüns	2aed66a955	temperature: Fix SOFT_PWM off by one A 128 step PWM has 127 intervals (0/127 ... 127/127 duty). Currently, a PWM setting of 1/127 is active for 2/128, i.e. double the expected time, or, in general n+1/128 instead of n/127. Fixes issue#6003. Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>	2017-03-24 04:13:36 -05:00
Scott Lahteine	b5711a99a2	Patches to bring UBL closer to compliance	2017-03-24 01:37:52 -05:00
Scott Lahteine	d076c1b604	Apply some general cleanup to code	2017-03-24 01:37:51 -05:00
Scott Lahteine	d1e6b0e21a	Reduce STEP_PULSE_CYCLES code slightly	2017-03-24 00:50:05 -05:00
Scott Lahteine	783338a0b8	Add UBL_MESH_EDIT_ENABLED to configs	2017-03-24 00:44:55 -05:00
Scott Lahteine	8d54ffbf05	Adjust vector_3 code with const, some optimization	2017-03-23 19:41:42 -05:00
Roxy-3D	8ee2612ebb	The hex nibble routine can print again! The code to print a hex nibble got broke. SERIAL_ECHO( (char) ) isn't suitable for its use.	2017-03-23 16:08:37 -05:00
Roxy-3D	b8e4a6970b	Get UBL up and running again All the changes to get the code into compliance with Marlin coding standards made UBL sick. This pretty much gets UBL back up and running.	2017-03-23 16:08:37 -05:00
Roxy-3D	5de1da2b3c	Make UBL honor the #define ENABLE_LEVELING_FADE_HEIGHT option	2017-03-23 16:08:37 -05:00
Scott Lahteine	8f9face956	Merge pull request #6088 from rafaljot/patch-3 Update Marlin_main.cpp	2017-03-23 01:51:51 -05:00
Scott Lahteine	782634b6c9	Merge pull request #6081 from Sebastianv650/MIN_STEPPER_PULSE_for_Babystepping Add MINIMUM_STEPPER_PULSE ability to babystepping	2017-03-22 21:57:36 -05:00
Scott Lahteine	af2ea23e9c	EXTRUDER_RUNOUT_PREVENT uses buffer_line_kinematic	2017-03-22 20:51:12 -05:00
Scott Lahteine	cd882b88db	#if defined => #ifdef / PIN_EXISTS	2017-03-22 20:51:11 -05:00
Scott Lahteine	e244399766	Additional cleanup of UBL code	2017-03-22 20:51:10 -05:00
Bob-the-Kuhn	0934563b97	G38 optional double touch Made the double touch portion a conditional compile based on the PROBE_DOUBLE_TOUCH flag. ============================================== Bugfix The current G38 only stopped a move if it involved the Z axis. Moved all the G38 code to it's own section and put it where it would always be executed no matter what axis was moving or if the endstop was enabled. Also added a comment to configuration_adv to alert the user the double tap had to be turned on. ============================================== Change G38 back to using Z_MIN_PROBE There's no Z_MIN endstop if Z_DUAL_ENDSTOPS is enabled and you have them set to the top of the gantry. G38 started out as using the Z_MIN_PROBE pin. I don't remember why we changed it to the Z_MIN endstop.	2017-03-22 15:08:49 -05:00
Scott Lahteine	cc3204509c	UBL patch from Bob-the-Kuhn	2017-03-22 07:54:20 -05:00
Scott Lahteine	b904b5ae8d	Audible feedback for settings store/load/reset	2017-03-22 02:15:21 -05:00
Sebastianv650	bf57eb2447	Protect Babystepping against other ISRs Especialy against stepper ISR. This is even more important when a minimum pulse width is set, increasing the runtime of a babystep.	2017-03-21 18:05:44 +01:00
Sebastianv650	80830919dc	Add MINIMUM_STEPPER_PULSE ability to babystepping	2017-03-21 17:50:38 +01:00
rafaljot	6da949bbf0	Update Marlin_main.cpp Sometimes after killing heaters are still on.	2017-03-21 15:06:01 +01:00
Roxy-3D	72f7b14e66	Make G29's Interactive Mesh Editor Work	2017-03-20 12:52:51 -05:00
Roxy-3D	3fd74b121f	Get G29's Interactive Mesh Editor running G29 P4 R O should work now.	2017-03-20 12:52:51 -05:00
Roxy-3D	1d58558bec	Spelling fix	2017-03-20 12:52:51 -05:00
Scott Lahteine	2573f4dd05	Merge pull request #6052 from thinkyhead/rc_lift_on_pause Add PARK_HEAD_ON_PAUSE feature / M125	2017-03-20 03:36:31 -05:00
Scott Lahteine	48c6284c91	Immediate commands take precedence	2017-03-19 21:50:48 -05:00
Roxy-3D	76c270fdf2	Allow FWRETRACT with UBL Enabled The retraction flag in UBL's G26 was conflicting with the FWRETRACT option. All fixed!	2017-03-19 15:43:12 -06:00
Roxy-3D	c377c59d47	Allow G29 P1 R to generate the mesh Fix the logic change that happened when UBL got merged.	2017-03-19 15:13:33 -06:00
Scott Lahteine	ff0dd162b7	PARK_HEAD_ON_PAUSE implementation	2017-03-19 07:27:35 -05:00
Scott Lahteine	26473cab6d	Add PARK_HEAD_ON_PAUSE feature	2017-03-19 05:06:55 -05:00
Scott Lahteine	4cf51157b3	Use XYZE rather than NUM_AXIS	2017-03-19 01:14:39 -05:00
Scott Lahteine	4c7f14752a	Add disable_e_steppers function	2017-03-19 01:14:39 -05:00
Scott Lahteine	8eb29f91e6	Patch filament change options and beep code	2017-03-19 01:14:39 -05:00
Scott Lahteine	56c9dfc83b	Merge pull request #6066 from thinkyhead/rc_felix_fix Update Felix config for UBL	2017-03-19 01:11:02 -05:00
Scott Lahteine	9b2b53f63a	Merge pull request #6042 from thinkyhead/rc_fix_toolchange_z Move Z last in tool-change for SWITCHING_EXTRUDER	2017-03-19 00:34:41 -05:00
Scott Lahteine	f98fb6b38e	Update Felix config for UBL	2017-03-19 00:28:48 -05:00
Scott Lahteine	7cabe81373	Merge pull request #6057 from thinkyhead/rc_followup_6054 Followup 6054 with some cleanup	2017-03-18 13:49:20 -05:00
Scott Lahteine	4bca27ab89	Fix Kelvin conversion Thanks to @ospalh -- #6056	2017-03-18 13:23:08 -05:00
Scott Lahteine	143ab8f329	Remove Roxy's personal configurations	2017-03-18 12:35:02 -05:00
Scott Lahteine	2512871a36	Patch configs UBL followup	2017-03-18 12:32:03 -05:00
Scott Lahteine	27b5666e15	Move Allen Key probe definition to the top	2017-03-18 12:27:37 -05:00
Scott Lahteine	77cf648ed3	Move menu selection past static items in 1 screen	2017-03-18 12:26:21 -05:00
Scott Lahteine	2c630a1b5c	Merge pull request #6054 from thinkyhead/rc_ubl_renewal UBL for RCBugFix — cleanup, rebase, patch	2017-03-18 12:07:57 -05:00
Scott Lahteine	0492a3a8f1	Merge pull request #6027 from Bob-the-Kuhn/add_kill_info Message for every KILL and STOP	2017-03-18 11:49:35 -05:00
Scott Lahteine	6618346148	Patches to work around "register spill" compiler bug	2017-03-18 11:35:21 -05:00
Scott Lahteine	be7dd90382	Add Thermistor 75: MGB18 silicon pad	2017-03-18 11:35:20 -05:00
Scott Lahteine	b0a9c82c31	Fix single-char echo and pinMode usage	2017-03-18 11:35:20 -05:00
Scott Lahteine	fb60aa3736	UBL implementation	2017-03-18 11:35:20 -05:00
Scott Lahteine	238b8fd2a3	UBL core and support files	2017-03-18 11:35:19 -05:00
Scott Lahteine	cf94688925	Univeral Bed Leveling - configuration	2017-03-18 11:35:19 -05:00
Scott Lahteine	03aa424ccb	Merge pull request #6053 from thinkyhead/rc_clean Remove extraneous whitespace	2017-03-18 03:26:45 -05:00
Scott Lahteine	af644871bf	Merge pull request #6045 from thinkyhead/rc_remove_raw_kinematics Remove delta optimization concepts… for now	2017-03-18 03:26:24 -05:00
Scott Lahteine	77491dd924	Remove extraneous whitespace	2017-03-18 03:17:39 -05:00
Scott Lahteine	b865b21d32	Can't use Z fade height with DELTA	2017-03-17 08:34:47 -05:00
Scott Lahteine	1e57b0c269	Remove delta interpolation concept	2017-03-17 06:32:11 -05:00
Scott Lahteine	e46898f8e5	Remove kinematic optimizations	2017-03-17 06:30:22 -05:00
Scott Lahteine	11f1fdfab4	_lcd_level_bed_position => manual_probe_index	2017-03-17 06:05:17 -05:00
Scott Lahteine	0e410c9dfd	Software endstop options as simple switches	2017-03-17 06:05:17 -05:00
Scott Lahteine	d01b915085	Implement soft_endstops_enabled for clamping	2017-03-17 06:05:17 -05:00
Scott Lahteine	e4649c9044	Add HAS_SOFTWARE_ENDSTOPS macro	2017-03-17 06:05:17 -05:00
Scott Lahteine	3e927ff204	Replace MBL Z hacking	2017-03-17 06:05:17 -05:00
Scott Lahteine	4e53124681	Merge pull request #6039 from Bob-the-Kuhn/M114-sync-with-stepper M114 - wait for move completion before reporting position	2017-03-17 05:22:46 -05:00
Scott Lahteine	734f9ea133	Merge pull request #6040 from thinkyhead/rc_sanity_use_assert Simplify some sanity checks with static_assert	2017-03-17 05:22:17 -05:00
Scott Lahteine	f02af83d42	Remove some extraneous spaces	2017-03-16 23:59:11 -05:00
Scott Lahteine	672e45652e	Improved solution to tool-change bug	2017-03-16 23:59:10 -05:00
Scott Lahteine	23f1cfb46f	Fix stuck CHDK pin as suggested in #6041	2017-03-16 21:49:39 -05:00
Scott Lahteine	0b22069e82	Merge pull request #6021 from Bob-the-Kuhn/BUG-FIX--Switching-extruder-tool-change-Z-height Bug Fix: Switching extruder tool change leaves Z in wrong position	2017-03-16 21:15:20 -05:00
Scott Lahteine	e7e4500629	Simplify some sanity checks with static_assert	2017-03-16 16:31:34 -05:00
Bob-the-Kuhn	34ff0c3439	M114 - wait for move completion before reporting position	2017-03-16 15:10:45 -05:00
Bob-the-Kuhn	b31604a492	Message for every KILL and STOP No more mystery halts & resets Moved messages to language.h Added current command to inactive timeout message	2017-03-15 21:05:11 -05:00
Kai	13b44d019b	Update language_de.h Addition of missing strings to match language_en.h	2017-03-15 16:06:52 +01:00
Bob-the-Kuhn	685ed5393a	Bug Fix: Switching extruder tool change leaves Z in wrong position The tool_change function saves the current_position to the destination array soon after starting. Later in the switching extruder section, the destination array is modified when moving the Z axis up & down. A later section of tool_change moves the head back to the “original location” using the destination array. This later section assumes that the destination array hasn’t been modified. The fix is to save the destination Z position and then restore it after the Z movements have completed. Going back to using the current_position array for the switching extruder Z axis moves (and leaving the destination array untouched) doesn’t fix the problem. This bug was introduced by the “Make tool_change kinematic compatible” commit # `847429eff4` which was merged on 10 Oct 2016 as part of PR 4982. This bug was discovered in Issue 5966.	2017-03-14 02:36:24 -05:00
Scott Lahteine	51353f8fea	Merge pull request #6000 from trivalik/NoWorkspaceWarning prevent warning with define of NO_WORKSPACE_OFFSETS	2017-03-12 00:00:51 -06:00
MagoKimbra	a4a9bd8bc9	Fix BUG set_position_mm Set postion must have axis and not E_AXIS + active_extruder.	2017-03-11 14:13:39 +01:00
Trivalik	71ac6f9d42	prevent warning with define of NO_WORKSPACE_OFFSETS	2017-03-09 23:49:57 +01:00
Stefan Brüns	9ba6c051a1	Makefile: add nozzle.cpp too CXXSRC list The file is required by the optional NOZZLE_PARK_FEATURE. Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>	2017-03-09 03:08:49 +01:00
Stefan Brüns	9cc8d495b8	Makefile: remove no longer existing search paths ArduinoAddons has been removed from Marlin, remove any references to it. Replace HARDWARE_SRC and HARDWARE_DIR with its expanded equivalents. Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>	2017-03-09 01:46:47 +01:00
Stefan Brüns	bf563e62c1	Makefile: add printcounter.cpp too CXXSRC list The file is required by the optional PRINTCOUNTER feature. Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>	2017-03-09 01:45:54 +01:00
Stefan Brüns	ddecc1441d	Makefile: Fix linker error Instantiation of the static singleton instance thermalManager in general requires locking, but we know its safe to do without. Add -fno-threadsafe-statics to avoid using locking primitives, which result in linking errors: undefined reference to `__cxa_guard_acquire' undefined reference to `__cxa_guard_release' Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>	2017-03-09 01:45:38 +01:00
MagoKimbra	37a26dfc09	Fix delta_angles	2017-03-08 09:23:30 +01:00
Scott Lahteine	2defb1d748	Use SET_INPUT_PULLUP where appropriate	2017-03-07 23:43:33 -06:00
Scott Lahteine	58b3e98878	Use arrays for delta tower parameters	2017-03-07 19:00:22 -06:00
Scott Lahteine	47242a40bb	Apply updated changes for delta_tower_angle_trim	2017-03-07 18:15:11 -06:00
Jimmy Envall	00b6b3da79	Added support for delta tower angle corrections.	2017-03-07 16:35:58 -06:00
Scott Lahteine	5a456c832a	Apply TMC2130 to example configurations	2017-03-07 04:22:06 -06:00
Scott Lahteine	45f949d833	TMC2130 Library: @teemuatlut replaces @makertum	2017-03-07 04:22:06 -06:00
Scott Lahteine	33f8a8a344	Merge pull request #5973 from thinkyhead/rc_circle_pattern Add circle pattern to nozzle clean	2017-03-06 04:47:01 -06:00
Scott Lahteine	94b3e0a483	Merge pull request #5959 from benlye/benlye-fixm48 Remove extra carriage return in M48 V1 output	2017-03-06 04:24:28 -06:00
Scott Lahteine	a9a1971295	Merge pull request #5972 from thinkyhead/rc_cooldown_before Fix preheat menu formatting	2017-03-06 03:21:29 -06:00
Scott Lahteine	6aa81255a9	Patch and clean up "flsun" kossel. Followup to #5911 .	2017-03-06 03:15:00 -06:00
Scott Lahteine	b2270b3f3e	Apply prior nozzle clean update	2017-03-06 03:14:59 -06:00
Marek Pikuła	7698c5617a	Added circle nozzle cleaning parameters to example configurations	2017-03-06 03:04:58 -06:00
Marek Pikuła	6836b94eea	Added circle pattern for nozzle cleaning feature	2017-03-06 03:03:00 -06:00
Scott Lahteine	3b75518ef6	Merge pull request #5911 from aphex3k/flsun_kossel_mini Configuration.h and Configuration_adv.h for the kossel mini by flsun	2017-03-06 02:26:01 -06:00
Scott Lahteine	3830778852	Apply NO_WORKSPACE_OFFSETS to lcd menu	2017-03-06 02:21:42 -06:00
Scott Lahteine	7e3aab889d	Fix preheat menu formatting	2017-03-06 02:07:07 -06:00
Scott Lahteine	fea0d3f20f	Endstop and temp-isr general cleanup	2017-03-06 02:07:07 -06:00
Scott Lahteine	aef08e8780	Compact some macro substitutions	2017-03-06 02:07:07 -06:00
Scott Lahteine	2f620f86d9	Merge pull request #5970 from thinkyhead/rc_cooldown_before Preheat Hotend Only menu items	2017-03-06 01:56:05 -06:00
Scott Lahteine	02de8e6f18	Merge pull request #5957 from MagoKimbra/rc_stepper_indirection_fix Stepper indirection fix tmc driver	2017-03-06 01:16:40 -06:00
Scott Lahteine	6c5312559c	Menu item to preheat only the hotend	2017-03-06 01:14:54 -06:00
Scott Lahteine	9d0142e8ae	Move Change Filament above Cooldown	2017-03-06 01:13:12 -06:00
Scott Lahteine	0c55095c5e	Move Cooldown above Preheat	2017-03-06 01:13:12 -06:00
Scott Lahteine	c15c65f18a	Merge pull request #5971 from thinkyhead/rc_fix_e_factors Patch DISTINCT_E_FACTORS bug	2017-03-06 01:11:17 -06:00
Scott Lahteine	bfb0007573	Patch DISTINCT_E_FACTORS bug	2017-03-05 23:19:31 -06:00
Scott Lahteine	be98016674	Merge pull request #5963 from thinkyhead/rc_no_offsets_optim New option: NO_WORKSPACE_OFFSETS	2017-03-05 21:46:49 -06:00
Scott Lahteine	8e89a802f7	Document PROTOCOL_VERSION	2017-03-05 04:43:46 -06:00
Scott Lahteine	87b03b16bd	Use a macro for array copies	2017-03-05 04:43:46 -06:00
Scott Lahteine	e141f3a03f	Optimize coordinate transformation Pre-compute the combined position shift and home offset to save a single float fetch-and-add per conversion. Great for delta/scara and bed leveling.	2017-03-05 04:43:16 -06:00
Scott Lahteine	5f7e85398b	Implement NO_WORKSPACE_OFFSETS	2017-03-05 04:43:15 -06:00
Scott Lahteine	05abe853f9	New option: NO_WORKSPACE_OFFSETS	2017-03-05 04:43:15 -06:00
Scott Lahteine	20addc6e32	Merge pull request #5955 from thinkyhead/rc_eeprom_fail_better Display a message for EEPROM version mismatch	2017-03-04 17:15:07 -06:00
benlye	dead89062a	Update Marlin_main.cpp Remove unnecessary line break from M48 V1 output.	2017-03-04 17:58:10 +00:00
MagoKimbra	ae277aebc6	Stepper indirection fix tmc driver	2017-03-04 12:17:39 +01:00
Scott Lahteine	8f4e4b1995	Display a message for EEPROM version mismatch	2017-03-04 01:20:36 -06:00
Scott Lahteine	177ad245f6	Merge pull request #5953 from thinkyhead/fix_fc_e_index Fix submenu hotend status display	2017-03-04 00:12:29 -06:00
Scott Lahteine	cea3ea772c	Fix submenu hotend status display	2017-03-03 22:12:22 -06:00
Scott Lahteine	b27f69ba51	Merge pull request #5813 from thinkyhead/rc_fix_makrpanel Fix MAKRPANEL assignments	2017-03-03 21:40:49 -06:00
Scott Lahteine	1ef6ccd919	Merge pull request #5951 from thinkyhead/rc_print_2d_array Reduce code size (40b, or 166b with bilinear subdivision)	2017-03-03 21:27:44 -06:00
Scott Lahteine	53f5086905	Fix MAKRPANEL assignments MAKRPANEL is a DOGLCD+ULTRA_LCD+NEWPANEL so customize its pins within that block.	2017-03-03 21:22:21 -06:00
Scott Lahteine	98c7b682ca	General cleanup, const usage, var naming	2017-03-03 20:57:49 -06:00
jes	369bfc8a1e	Reduce code size (40b, or 166b with bilinear subdivision)	2017-03-03 20:36:32 -06:00
Scott Lahteine	0d13412105	Fix "Heating..." message	2017-03-03 12:12:51 -06:00
Scott Lahteine	5065636023	Merge pull request #5934 from thinkyhead/rc_advance_ed_ratio LIN_ADVANCE: Fixed E/D ratio option	2017-03-03 03:24:41 -06:00
divendres	75ad82baab	Update Catalan language	2017-03-02 20:40:06 -06:00
Scott Lahteine	34253497d4	Babysteps code tweak As suggested by https://github.com/MarlinFirmware/Marlin/pull/5887#issuecomment-283832163	2017-03-02 20:35:45 -06:00
Scott Lahteine	fb4aead2b1	Clean up and finish #5887	2017-03-02 20:16:29 -06:00
Scott Lahteine	b3e2bd6f29	Reduce E_D_ratio code	2017-03-02 01:00:37 -06:00
Sebastianv650	de6c40ed8f	Add option to fix E/D ratio Work around for slicers producing buggy gcode.	2017-03-02 01:00:37 -06:00
Scott Lahteine	eeb490221f	Remove BEEPER_PIN override in pins_RIGIDBOARD.h Resolves #5926. This override is no longer needed since the RAMPS LCD controller pins were fixed.	2017-03-01 18:26:29 -06:00
Roxy-3D	11e892bd84	Merge pull request #5887 from Roxy-3D/RCBugFix Double Click of Encoder Wheel Jumps to Z-BabyStepping	2017-03-01 17:15:02 -07:00
Scott Lahteine	cbeff12f8a	Merge pull request #5933 from teemuatlut/lcd_days_hours Fix formatting of SD print time hours above one day	2017-03-01 15:44:10 -06:00
Scott Lahteine	8a4e9d08a3	Merge pull request #5931 from thinkyhead/rc_core_endstop_fix Fix CoreYX / YZ / ZX endstop logic	2017-03-01 15:32:11 -06:00
teemuatlut	9175d16660	Fix formatting of print time hours above one day	2017-03-01 18:55:25 +02:00
Scott Lahteine	b6d9eb229f	Extend Core endstop commentary	2017-03-01 10:01:50 -06:00
Bob-the-Kuhn	c5e08e8761	CoreYX/YZ/ZX needs different endstop logic than CoreXY/YZ/XZ In the endstop testing section, add the "reverse" logic in addition to "normal" core handling. In CoreXY/YZ/XZ steppers rotating the same direction gives X movement. Opposing directions produces Y movement. In CoreYX/ZY/ZX this is reversed. Same = Y, Opposite = X. ---- Fixes the issue where the Y endstop was being checked when moving in the X direction, etc.	2017-03-01 09:40:24 -06:00
Scott Lahteine	c759c26cca	Make LCD_TIMEOUT_TO_STATUS configurable As suggested in https://github.com/MarlinFirmware/Marlin/issues/5570#issuecomment-283059 065	2017-02-28 19:02:50 -06:00
Michael Henke	47729918fc	enable ENSURE_SMOOTH_MOVES	2017-02-27 20:42:49 -08:00
Michael Henke	330b981912	created Configuration.h and Configuration_adv.h for the kossel mini sold by flsun	2017-02-25 21:31:37 -08:00
Colin Gilgenbach	48b7e0f8d8	Nozzle Wipe Vertical Zig-Zag - Add configuration support for zigzags in either the X or Y axis, for wipe pads significantly longer in one dimension. - Add configuration for default number of zig-zag triangles, vs. a magic number in `Marlin_main.cpp`. - Update description of auto nozzle wiping to match functionality	2017-02-25 21:52:43 -06:00
Scott Lahteine	f17b81b765	Add MAPPER_C2C3 to French language	2017-02-25 18:49:00 -06:00
Roxy-3D	7e607b06eb	Better comments on DOUBLE_CLICK_TIME_WINDOW	2017-02-23 13:13:57 -07:00
Scott Lahteine	34cba42104	Use PSTR for MSG_HEATING	2017-02-22 11:30:19 -06:00
Roxy-3D	584d147a02	fixup the indentation	2017-02-22 07:23:54 -07:00
Roxy-3D	e443e0e2a9	Fix scoping issues for double click to Z-Babystepping	2017-02-21 18:15:28 -07:00
Roxy-3D	17d1cd7c09	Double Click of Encoder Wheel Jumps to Z-BabyStepping	2017-02-21 18:08:19 -07:00
Roxy-3D	48d862377a	Double Click of Encoder Wheel Jumps to Z-BabyStepping	2017-02-21 18:04:31 -07:00
Scott Lahteine	cfdc189796	Merge pull request #5856 from thinkyhead/rc_fix_bad_comment Remove non-applicable comment on MANUAL_Z_HOME_POS	2017-02-20 17:54:30 -06:00
dot-bob	cd68380ce6	Add status_printf to print messages to the lcd status line. Also add a hotend indicator to the heating message displayed on the lcd status line.	2017-02-20 15:26:54 -06:00
Scott Lahteine	012aff6823	Merge pull request #5862 from thinkyhead/rc_fix_a_thing Finish reducing of ABL_BILINEAR_SUBDIVISION	2017-02-18 21:36:28 -06:00
Scott Lahteine	b9187020c4	Finish reducing of ABL_BILINEAR_SUBDIVISION	2017-02-18 20:01:19 -06:00
Scott Lahteine	e282b72151	Remove non-applicable comment on MANUAL_Z_HOME_POS	2017-02-18 05:14:43 -06:00
Scott Lahteine	57f92a4632	Apply DISTINCT_E_FACTORS to sync_from_steppers Followup to #5840	2017-02-18 04:36:41 -06:00
Scott Lahteine	4da8b1494b	Merge pull request #5854 from thinkyhead/rc_fixup_m600 M600 cleanup and bugfix	2017-02-18 04:27:13 -06:00
Scott Lahteine	dd02dba6e6	Merge pull request #5840 from MagoKimbra/rc_fix_lin_advanced_step_to_mm Fix steps_to_mm for active extruders	2017-02-18 04:25:53 -06:00
Scott Lahteine	6e0b3fcc08	Optimize M600 heater status LCD items	2017-02-18 04:08:00 -06:00
Scott Lahteine	44b4e116bd	Commentary / style in gcode_M600	2017-02-18 04:08:00 -06:00
Scott Lahteine	561904345f	Tweak config ordering for M600	2017-02-18 00:01:31 -06:00
Scott Lahteine	284d6de9da	Remove some old code comments	2017-02-17 15:25:56 -06:00
MagoKimbra	3685224c1a	Fix steps_to_mm for active extruders	2017-02-15 21:45:39 +01:00
Scott Lahteine	4578c573fe	Pause the print job timer while in M600	2017-02-15 05:29:34 -06:00
Scott Lahteine	bfe6f71794	Simplify filament_change_beep function	2017-02-15 05:29:34 -06:00
Scott Lahteine	8289ea1316	Use a short name for the filament "endstop"	2017-02-15 05:29:34 -06:00
Scott Lahteine	d9dcef8a87	Spacing, coding standards	2017-02-15 05:29:34 -06:00
Scott Lahteine	931914e679	Apply M600 updates to all configs	2017-02-15 05:29:34 -06:00
Roxy-3D	8bf0b496b9	Improve M600 with timeout, wait for heatup.	2017-02-15 05:29:34 -06:00
Tannoo	c40fe2113c	Fix for broken MBL LCD call was waiting forever, causing the system to hang.	2017-02-15 04:39:22 -06:00
Scott Lahteine	4d4745c0eb	Parenthesize some menu defines for safety	2017-02-14 23:12:27 -06:00
Scott Lahteine	47f9883b0f	Dynamic allocation for SDCARD_SORT_ALPHA	2017-02-14 21:37:25 -06:00
Scott Lahteine	a561bd5e3a	New feature: SDCARD_SORT_ALPHA	2017-02-14 21:37:24 -06:00
Scott Lahteine	c04d6b5aa6	Merge pull request #5829 from thinkyhead/rc_fix_isr_reentry Combine fixes for LIN_ADVANCE and temperature ISR	2017-02-14 20:36:58 -06:00
Scott Lahteine	467f01435f	Merge pull request #5816 from thinkyhead/rc_abl_virt_reduce Reduce memory use by ABL_BILINEAR_SUBDIVISION slightly	2017-02-14 08:41:44 -06:00
Scott Lahteine	97b6fb6381	Reduce / optimize LIN_ADVANCE code	2017-02-14 07:52:03 -06:00
Sebastianv650	271ced7341	Prevent re-entering of temperature ISR If Marlin is inside the temperature ISR, the stepper ISR is enabled. If a stepper event is now happening Marlin will proceed with the stepper ISR. Now, at the end of the stepper ISR, the temperatre ISR gets enabled again. While Marlin proceed the rest of the temperature ISR, it's now vulnerable to a second ISR call.	2017-02-14 07:52:03 -06:00
Sebastianv650	1b59766fcb	Cleanup position_float Hopefully fixes Marlin #5481	2017-02-12 13:09:06 +01:00
Scott Lahteine	a950c31e2d	Merge pull request #5815 from thinkyhead/rc_pulses_per_step Give encoder pulse/steps conditionals their own block	2017-02-12 04:14:00 -06:00
Scott Lahteine	7176de8605	Merge pull request #5814 from thinkyhead/hotend_loop_always Make HOTEND_LOOP more consistent, let compiler optimize it	2017-02-12 04:13:14 -06:00
Scott Lahteine	adec219ca5	Merge pull request #5811 from thinkyhead/fix_two_strings No space after X: or A: in M114 output	2017-02-12 04:11:51 -06:00
jes	eaa829b58c	Reduce memory use by ABL_BILINEAR_SUBDIVISION slightly	2017-02-12 04:09:48 -06:00
Scott Lahteine	1c99ca82d8	Give encoder pulse/steps conditionals their own block	2017-02-12 03:57:57 -06:00
Scott Lahteine	e44294bb4d	Make HOTEND_LOOP more consistent, let compiler optimize it	2017-02-12 02:50:38 -06:00
Scott Lahteine	701f4a6d9d	Merge pull request #5729 from Bob-the-Kuhn/guaranteed-BLTouch-detection guaranteed BLTouch detection	2017-02-12 01:13:35 -06:00
Scott Lahteine	c15b9a6a06	No space after X: or A: in M114 output	2017-02-12 00:10:03 -06:00
Scott Lahteine	e1702816f6	Fix SD_CHECK_AND_RETRY condition Addressing #5806	2017-02-11 23:55:56 -06:00
Scott Lahteine	1bc5be3bdf	Cast DELTA_PRINTABLE_RADIUS to float in sq() Addressing #5625	2017-02-11 23:28:39 -06:00
Bob-the-Kuhn	0369f97ec1	guaranteed BLTouch detection To guarantee that the 5mS pulse from a BLTouch is recognized you need to have the endstops.update() routine run twice in that 5mS period. At 200 steps per mm, my system has problems below a feedrate of 120 mm per minute. Two things were done to guarantee the two updates within 5mS: 1) In interrupt mode, a check was added to the temperature ISR. If the endstop interrupt flag/counter is active then it'll kick off the endstop update routine every 1mS until the flag/counter is zero. This flag/counter is decremented by the temperature ISR AND by the stepper ISR. 2) In poling mode, code was added to the stepper ISR that will make sure the ISR runs about every 1.5mS. The "extra" ISR runs only check the endstops. This was done by grabbing the intended ISR delay and, if it's over 2.0mS, splitting the intended delay into multiple smaller delays. The first delay can be up to 2.0mS, the next ones 1.5mS (as needed) and the last no less than 0.5mS. ========================================= BLTouch error state recovery If BLTouch already active when deploying the probe then try to reset it & clear the probe. If that doesn't fix it then declare an error. Also added BLTouch init routine to startup section	2017-02-11 12:01:34 -06:00
Scott Lahteine	1e4d4e5915	Fix typo in language_uk Thanks to @pavlus for this one	2017-02-10 15:34:31 -06:00
Scott Lahteine	7fe7a0c8be	Merge pull request #5793 from thinkyhead/rc_adjust_probe_output Adjust probe_pt() terminal output to respect probe z-offset	2017-02-09 23:05:02 -06:00
Scott Lahteine	633c253bc1	Merge pull request #5792 from thinkyhead/rc_default_dac_vals Default DAC values for RigidBoard V2	2017-02-09 22:56:03 -06:00
Florian Heilmann	7bbc31704c	Adjust probe_pt() terminal output to respect probe z-offset	2017-02-09 22:54:22 -06:00
Scott Lahteine	a245656db3	Merge pull request #5713 from gege2b/RCBF-French French translation : Added missing strings as well as missing accents	2017-02-09 22:43:56 -06:00
jaysonkelly	713931338a	Default DAC values for RigidBoard V2	2017-02-09 22:39:00 -06:00
Bob-the-Kuhn	ae706233a8	pinsDebug for 644/1284 & USB646/1286 families added conditional compilation for PWMs 1C & 3C add Teensyduino compatibility ========================================== changes per review - minor formatting changes 1) remove non-printable character at the end of line 687 2) split a really long comment into two lines 3) got rid of some trailing spaces ============================================ Made pinsDebug_Teensyduino.h the same between this PR and PR 5668 which is for a re-written pinsDebug.h file. The changes were: 1) added copyright @ GNU license header 2) a blank line crept in.	2017-02-09 07:24:02 -06:00
Gege2B	22dfcc9a71	French translation : Added missing strings as well as missing accents	2017-01-17 23:29:23 +01:00
Scott Lahteine	9b5515926a	Merge pull request #5696 from thinkyhead/rc_volumetric_default Allow enabling volumetric filament on config load	2017-01-14 05:48:51 -08:00
Robert Kirk	0d147ead66	Allow enabling volumetric filament on config load	2017-01-14 04:37:49 -08:00
AnHardt	fa26767efe	Replace all remaining 'boolean' with 'bool'	2017-01-13 13:03:52 +01:00
AnHardt	f6858d9974	Fix M110 without leading N Store N in the right variable. This is too rarely used. "mea culpa, mea culpa, mea maxima culpa"	2017-01-13 12:33:50 +01:00
Scott Lahteine	0c0c840ba8	Merge pull request #5683 from emartinez167/EMartinez-Changes Updates to some incorrectly ended strings in the Spanish translation	2017-01-12 07:49:15 -08:00
Kai	25dae3bccc	Update language_de.h Small corrections	2017-01-12 16:06:58 +01:00
emartinez167	7292145f4e	Fix for some wrong strings On last commit, some strings were ended with the incorrect character. This fixes it.	2017-01-12 22:35:04 +08:00
Scott Lahteine	93a9aa6b76	Merge pull request #5682 from thinkyhead/rc_spanish_jan Updates to Spanish language	2017-01-12 06:14:10 -08:00
Scott Lahteine	7a9c1a279b	Merge pull request #5681 from thinkyhead/rc_prevent_boot_loop Reset watchdog in SD init to prevent reboot	2017-01-12 06:13:56 -08:00
Scott Lahteine	e409c7f9e8	Merge pull request #5645 from esenapaj/From-microseconds-to-milliseconds From "microseconds" to "milliseconds"	2017-01-12 06:02:55 -08:00
emartinez167	020c6af7b0	Updates to Spanish language Add missing Spanish language definitions.	2017-01-12 05:53:39 -08:00
Hans Raaf	d29cc8f7bc	Reset watchdog in SD init to prevent reboot If the watchdog is enabled and bootscreen + SD card checks take too long, Marlin may hang at boot time because of the reset loop. We have this happen all the time with the Anet board if no SD card is inserted.	2017-01-12 05:33:38 -08:00
Scott Lahteine	7743849608	Merge pull request #5680 from thinkyhead/rc_configs_puhlease code_value_float tweak	2017-01-12 05:22:47 -08:00
Scott Lahteine	16357fbfdf	Merge pull request #5619 from Ocarthon/RCBugFix Disable SD Detect for K8400	2017-01-12 05:22:03 -08:00
Scott Lahteine	e57c0fce66	Move MOSFET changes above #include for RIGIDBOARD Correction to #5629	2017-01-12 04:46:49 -08:00
Scott Lahteine	c376f6a2cb	code_value_float tweak	2017-01-12 04:38:09 -08:00
Scott Lahteine	fb3c30e24c	Fix lcd_wait_for_homing causing menu to block As a showcase function for how to do waiting in the lcd menu, this function should be preserved.	2017-01-12 04:37:23 -08:00
Scott Lahteine	f8ae0fd29f	Merge pull request #5647 from manianac/RCBugFix-PrepareMenuFix Fix empty Prepare menu	2017-01-12 04:20:18 -08:00
Robert Kirk	aab5118c6a	Remove error causing break command Use index macro instead of e	2017-01-01 17:47:01 -05:00
esenapaj	d38e335272	From "microseconds" to "milliseconds" delay() is milliseconds	2017-01-02 01:19:33 +09:00
Philip Standt	8ae2bc7e2e	Disable SD Detect for K8400	2016-12-28 23:21:18 +01:00
Scott Lahteine	4061fca1ad	Sanity checks for FILAMENT_CHANGE_FEATURE and FILAMENT_RUNOUT_SCRIPT	2016-12-23 19:55:12 -08:00
Scott Lahteine	5ab7b91615	Comment on filament runout sensor config	2016-12-23 19:50:27 -08:00
Scott Lahteine	922c67f17d	Merge pull request #5588 from thinkyhead/rc_remove_biv25 Drop biv2.5 delta configurations	2016-12-23 19:14:50 -08:00
Scott Lahteine	8c6c048551	drop biv2.5 delta configurations	2016-12-23 18:56:07 -08:00
Scott Lahteine	92dbeebf40	Define ADV_NEVER, ADV_RATE	2016-12-23 18:43:23 -08:00
Robert Kirk	306c184b1a	Allow M600 when dryrun debugging	2016-12-21 20:30:51 -05:00
Scott Lahteine	fe2ea2906f	Merge pull request #5573 from thinkyhead/rc_unify_stepper_isr LIN_ADVANCE with unified stepper ISR	2016-12-21 02:53:32 -08:00
Sebastianv650	84c685f8b5	First draft of Unified Stepper / E Advance ISR	2016-12-21 01:34:39 -08:00
Scott Lahteine	83021d82c6	Merge pull request #5502 from AnHardt/symbol-strings Add symbol-strings	2016-12-21 00:51:59 -08:00
Scott Lahteine	036eccfd6e	Merge pull request #5572 from Kaibob2/patch-5 Update language_de.h	2016-12-21 00:50:40 -08:00
Scott Lahteine	b794b76836	Merge pull request #5567 from AnHardt/fix5194 Fix 5194	2016-12-21 00:49:52 -08:00
Scott Lahteine	451ba5df01	Merge pull request #5516 from esenapaj/Suppress-warning Suppress warning	2016-12-21 00:00:35 -08:00
Scott Lahteine	92dbc63949	Merge pull request #5571 from esenapaj/Update-Japanese-translation Update Japanese translation	2016-12-20 23:59:55 -08:00
Kai	ade72535c4	Update language_de.h Added tarnslation for ``` #define MSG_DEBUG_MENU #define MSG_PROGRESS_BAR_TEST ```	2016-12-21 08:57:39 +01:00
esenapaj	ab6b005867	Suppress warning	2016-12-21 09:13:03 +09:00
AnHardt	61f15ef7e7	Fix 5194 I have been a bit too radical in cleaning up this section.	2016-12-21 00:45:29 +01:00
esenapaj	60515ff700	Update Japanese translation ・Add new translation	2016-12-21 08:44:07 +09:00
Scott Lahteine	1e419655f3	Followup to #5550 - spacing before "mm"	2016-12-20 02:27:54 -08:00
Scott Lahteine	1a26ce1cdc	Merge pull request #5550 from FHeilmann/patch-2 Allow negative retract values in the LCD	2016-12-20 02:10:22 -08:00
Scott Lahteine	bec30c89e7	Merge pull request #5522 from esenapaj/Add-description-for-dual-x Add description for choice of DEFAULT_DUAL_X_CARRIAGE_MODE	2016-12-20 01:31:53 -08:00
Scott Lahteine	7739c0affa	Change "+mm" to "mm" in most languages - Japanese and Chinese still need update	2016-12-20 01:16:51 -08:00
Scott Lahteine	1cba425308	Allow negative recover-swap length from LCD	2016-12-20 01:16:08 -08:00
Scott Lahteine	298a8c6a3c	Merge pull request #5561 from thinkyhead/rc_no_case_light Support for M335 case light "no case light"	2016-12-20 01:06:59 -08:00
Scott Lahteine	644f45cbd8	Merge pull request #5563 from akaJes/m600 FILAMENT_CHANGE_FEATURE allowed in idle mode	2016-12-20 01:06:10 -08:00
Scott Lahteine	0d2fc13516	Place "Level Bed" closer to "Auto Home"	2016-12-20 00:51:03 -08:00
Scott Lahteine	b031d28ebf	Encoder events should not skip stripes	2016-12-20 00:21:51 -08:00
Scott Lahteine	22881f38b9	Fix updating of "bool" menu items	2016-12-20 00:21:51 -08:00
Scott Lahteine	eb68715b94	No "Cooldown" menu if heaters are off	2016-12-20 00:21:51 -08:00
Jesus	4ed976b5ff	m600 fixes	2016-12-20 09:47:46 +02:00
Damien	4e2639942b	Support for M335 case light "no case light"	2016-12-19 23:23:08 -08:00
Scott Lahteine	18ba31e9b5	Add Debug Menu with LCD_PROGRESS_BAR_TEST as an example	2016-12-19 22:57:14 -08:00
Scott Lahteine	03af5961b0	Hide (or remove) custom character change on boot screen	2016-12-19 22:27:28 -08:00
Scott Lahteine	1642f5ed31	Add macro to some en strings	2016-12-19 22:27:28 -08:00
Scott Lahteine	dbb2d56c89	Correct comment on watchdog timer	2016-12-19 22:27:28 -08:00
Scott Lahteine	41a30923f3	Merge pull request #5559 from thinkyhead/rc_minimum_gcc_version Throw an error for gcc before 4.7	2016-12-19 19:50:44 -08:00
Scott Lahteine	6d6a1db6ec	Apply const to _EEPROM_writeData value param	2016-12-19 18:50:43 -08:00
Robert Kirk	f724ef5820	Have bed leveling status output current status, not requested.	2016-12-19 18:47:45 -08:00
Scott Lahteine	20218e553d	Merge pull request #5527 from MagoKimbra/rc_configuration_store_fix_size Fix size	2016-12-19 18:47:28 -08:00
Scott Lahteine	dcfbe2bd3c	Throw an error for gcc before 4.7	2016-12-19 18:30:51 -08:00
Scott Lahteine	82fde7df2e	Merge pull request #5512 from AnHardt/speed-compare-bbr Optimize handling of block_buffer_runtime()	2016-12-19 18:21:06 -08:00
Scott Lahteine	8986225752	Spacing, cleanup in speed_lookuptable.h	2016-12-19 14:52:45 -08:00
Scott Lahteine	e12c8e5cac	Split up thermistor tables	2016-12-19 14:47:54 -08:00
Florian Heilmann	a7334fd2a0	Allow negative retract values in the LCD This can already be done via G-Code, so adding the capability to the LCD should be straight forward.	2016-12-19 14:19:06 +01:00
AnHardt	292eb365c6	Optimize handling of block_buffer_runtime() millis_t is long - divisions take for ever. Return a kind of millisecond instead of microsecond - divided by 1024 instead of 1000 for speed. (2.4% error) That does not matter because block_buffer_runtime is already a too short estimation. Shrink the return-type.	2016-12-19 11:47:28 +01:00
esenapaj	6854f44bf2	Add description for choice of DEFAULT_DUAL_X_CARRIAGE_MODE	2016-12-19 02:21:10 +09:00
Scott Lahteine	3f6f036f7c	Merge pull request #5524 from thinkyhead/rc_optional_dogm_splitup Report EEPROM data size, not final index	2016-12-16 18:55:48 -08:00
MagoKimbra	86ba7e4542	Fix size Fix size for writeData and readData. For bilinear grid 11 x 11 for example, size is 4 (float) x 11 x 11 = 484. uint8_t max is 255.	2016-12-16 14:49:33 +01:00
Scott Lahteine	f9f75c8016	Fix USE_RAW_KINEMATICS in prepare_kinematic_move_to	2016-12-15 23:15:38 -08:00
Scott Lahteine	87921f390a	Clarify what are "logical" positions in the planner	2016-12-15 23:15:38 -08:00
Scott Lahteine	a4f10f59c3	Write the E parameter length correctly	2016-12-15 23:15:38 -08:00
Scott Lahteine	2e904cb4f9	Merge pull request #5514 from esenapaj/Update-Japanese-translation Update Japanese translation	2016-12-15 21:38:40 -08:00
Scott Lahteine	0b6817e0f9	Merge pull request #5505 from android444/patch-4 Update for translations language_pl.h	2016-12-15 21:38:18 -08:00
Scott Lahteine	3bd76f60e4	Report EEPROM data size, not final index	2016-12-15 20:26:28 -08:00
Scott Lahteine	78d6d6e076	Merge pull request #5452 from thinkyhead/rc_save_your_mesh Save Bed Leveling to EEPROM	2016-12-15 20:23:01 -08:00
Scott Lahteine	0d0aa6c20d	Patch type for max_acceleration_mm_per_s2 save/restore	2016-12-15 20:05:42 -08:00
Scott Lahteine	d4f5418802	Merge pull request #5517 from esenapaj/Fix-for-PR-#5255 Fix for the PR #5255 (Case light menu (3rd attempt))	2016-12-15 20:01:22 -08:00
Scott Lahteine	fa7010b0a1	Merge pull request #5515 from esenapaj/Remove-unnecessary-tabs-and-spaces Remove unnecessary tabs and spaces	2016-12-15 19:58:32 -08:00
Scott Lahteine	6d7b1cdf6c	Add M421 for ABL Bilinear	2016-12-15 19:39:11 -08:00
Scott Lahteine	32e65dc429	Extend `M420` to print state and, with `V`, the matrix / mesh	2016-12-15 19:39:11 -08:00
Scott Lahteine	d04258753b	Don't throw away the bed level matrix on G28	2016-12-15 19:21:18 -08:00
Scott Lahteine	8f0f225d10	Save ABL Planar Matrix to EEPROM	2016-12-15 19:21:15 -08:00
Scott Lahteine	e2429a9da1	Generalize Bed Leveling flag in EEPROM	2016-12-15 19:20:52 -08:00
Scott Lahteine	e42fd7813a	Save ABL Bilinear Grid to EEPROM	2016-12-15 19:20:48 -08:00
Scott Lahteine	492b68f8e3	Better EEPROM read/write error handling	2016-12-15 19:08:44 -08:00
Scott Lahteine	55722c09da	Use "UNPROBED" for un-probed bed_level_grid points	2016-12-15 19:08:44 -08:00
Scott Lahteine	2643404ac8	Throw an error in M420 if can't enable	2016-12-15 19:08:43 -08:00
Scott Lahteine	b1539394fd	Use planner.unapply_leveling to undo tilt in G29	2016-12-15 19:08:43 -08:00
Scott Lahteine	04636f78eb	Re-enable MBL/ABL after M48	2016-12-15 19:08:43 -08:00
Scott Lahteine	9b41638672	Minor tweak to G29 grid points	2016-12-15 19:08:42 -08:00
Scott Lahteine	daa2cad21f	Fix comment on G29 to include 'Z'	2016-12-15 19:08:42 -08:00
Scott Lahteine	8244fefcc2	Tweak call to `reset_bed_level` in G29	2016-12-15 19:08:42 -08:00
Scott Lahteine	0995a5d734	Fixup reset_bed_level	2016-12-15 19:08:42 -08:00
Scott Lahteine	1b2fb2bdc7	ABL_GRID_POINTS_* => ABL_GRID_MAX_POINTS_*	2016-12-15 19:08:41 -08:00
esenapaj	d486361c69	Fix for commented section of Config_RetrieveSettings()	2016-12-16 04:34:47 +09:00
esenapaj	88157ba529	Fix for the PR #5255 (Case light menu (3rd attempt))	2016-12-16 00:57:32 +09:00
esenapaj	069c6b38dd	Remove unnecessary tabs and spaces	2016-12-16 00:21:32 +09:00
esenapaj	9c8116aedf	Update Japanese translation ・Add new translation	2016-12-16 00:06:58 +09:00
AnHardt	57b1275cde	Add symbol-string to _de Add symbol-string for _de to reduce the frquencey of regenerating 'mappers' and 'fonts' with the new utf-system.	2016-12-15 14:37:18 +01:00
android444	3363d2c937	Update for translations language_pl.h	2016-12-14 17:32:33 +01:00
Scott Lahteine	06af3b62ba	Move HOLLOW_FRAME options to config_adv	2016-12-14 04:31:27 -08:00
Scott Lahteine	67ca6c7bfe	Codestyle tweaks to ultralcd.cpp	2016-12-14 04:20:33 -08:00
Scott Lahteine	8d9fcd8e6f	Merge pull request #5495 from AnHardt/autoadjusting_display-updates Adaptive screen updates for all kinds of displays	2016-12-14 04:16:26 -08:00
Scott Lahteine	77a360912d	Merge pull request #5491 from yhfudev/devel-rcbugfix-language-headers UTF-8 language header files	2016-12-14 02:23:09 -08:00
AnHardt	d0e24e0876	Adaptive screen updates for all kinds of displays The target here is to update the screens of graphical and char base displays as fast as possible, without draining the planner buffer too much. For that measure the time it takes to draw and transfer one (partial) screen to the display. Build a max. value from that. Because ther can be large differences, depending on how much the display updates are interrupted, the max value is decreased by one ms/s. This way it can shrink again. On the other side we keep track on how much time it takes to empty the planner buffer. Now we draw the next (partial) display update only then, when we do not drain the planner buffer to much. We draw only when the time in the buffer is two times larger than a update takes, or the buffer is empty anyway. When we have begun to draw a screen we do not wait until the next 100ms time slot comes. We draw the next partial screen as fast as possible, but give the system a chance to refill the buffers a bit. When we see, during drawing a screen, the screen contend has changed, we stop the current draw and begin to draw the new content from the top.	2016-12-13 18:44:34 +01:00
yhfudev	2dbd38ce16	tag the utf-8 strings	2016-12-13 11:54:35 -05:00
Scott Lahteine	94ffb58da7	Prevent retract un-hop at wrong height	2016-12-13 08:24:12 -08:00
Scott Lahteine	0772c8e55f	Merge pull request #5487 from thinkyhead/rc_easier_move_axis Rearrange Move Menu, Fix up Delta Calibration	2016-12-13 07:07:05 -08:00
Scott Lahteine	b2c8de856b	Merge pull request #5478 from AnHardt/stepspermm Replace ftostr62sign with ftostr62rj	2016-12-13 07:05:42 -08:00
Scott Lahteine	1fd8185d37	Merge pull request #5492 from thinkyhead/rc_fix_language_es Fix multiple definitions of message macros in the language-es.h	2016-12-13 06:57:52 -08:00
yhfudev	1cdffdede7	fix multiple definitions of message macros in the language-es.h	2016-12-13 06:48:38 -08:00
Scott Lahteine	b67f8cb499	Merge pull request #5490 from jbrazio/update-bqhp2 Update the bq Hephestos 2 example configuration	2016-12-13 05:04:24 -08:00
Scott Lahteine	93b2833347	Move Menu: Select axis first, resolution after	2016-12-13 03:11:14 -08:00
Scott Lahteine	48aa0f6475	Merge pull request #5475 from AnHardt/utf-mapper-tr utf8-mapper for Turkish	2016-12-13 03:03:22 -08:00
Scott Lahteine	b9ee0d7bd3	Merge pull request #5488 from thinkyhead/rc_fade_compiler_warn Patch fade_factor compiler warning	2016-12-13 03:00:47 -08:00
Scott Lahteine	641e0936d4	Patch up Delta Calibration Menu	2016-12-13 02:42:28 -08:00
Scott Lahteine	b4dbf4d18a	Non-reentrant "Moving..." screen to safely wait in LCD	2016-12-13 02:42:27 -08:00
Scott Lahteine	7b625e0048	Patch fade_factor compiler warning	2016-12-13 02:29:01 -08:00
Scott Lahteine	6fa8fd15e2	Add negative temperatures for Thermistor 1 Changes from #5485 by @AndKe	2016-12-13 02:06:16 -08:00
Scott Lahteine	2b5d424394	Use handle_reprapworld_keypad for keypad handling	2016-12-13 01:41:08 -08:00
Scott Lahteine	887ed73c9b	Expose delta_clip_start_height for use by others	2016-12-13 01:41:08 -08:00
João Brázio	3f75edb1d6	Updated bq Hephestos 2 example configuration	2016-12-13 09:26:07 +00:00
Daniel Martinez	b796e7031d	Update Aragonese translation	2016-12-12 17:36:33 -08:00
AnHardt	cd2b74e88d	Replace ftostr62sign with ftostr62rj `ftostr62sign()` is used only when displaing/editing Steps/mm. A sign is not needed - the value is always positive. Because the number part is long there is no't much place for the values name. With this PR the is one more char for the name possible.	2016-12-12 20:25:20 +01:00
AnHardt	795541f87e	utf8-mapper for Turkish The non utf8 version of turkish is a bit unhandy. Delete `language_tr.h` Rename `language_tr_utf.h` to `language_tr.h` Provide a propper utf8-mapper for Turkish and use it.	2016-12-12 15:56:59 +01:00
Scott Lahteine	7c71bb2900	Merge pull request #5471 from thinkyhead/rc_planner_report_m503 Patch to show E factors in M503	2016-12-11 17:47:41 -08:00
Scott Lahteine	39401b7472	Patch to show E factors in M503	2016-12-11 17:37:29 -08:00
Scott Lahteine	6b50230022	Merge pull request #5447 from thinkyhead/rc_update_dutch Dutch cleanup, ordering, placeholders	2016-12-10 22:13:20 -08:00
Scott Lahteine	2c97c11731	Merge pull request #5454 from thinkyhead/rc_fix_delta_g29 Fix G29 starting height on DELTA	2016-12-10 22:10:33 -08:00
Scott Lahteine	8239c45b30	Merge pull request #5448 from thinkyhead/rc_eeprom_bump EEPROM: Prolong life. Better support for `DISTINCT_E_FACTORS`.	2016-12-10 22:06:00 -08:00
Scott Lahteine	21ed43df5f	New Dutch terms	2016-12-10 21:59:45 -08:00
Scott Lahteine	4bc6536f54	Move to safe zone on DELTA if using do_blocking_move_to*	2016-12-10 21:28:24 -08:00
Scott Lahteine	6f389158d7	Compile less code with EEPROM off	2016-12-09 06:05:32 -08:00
Scott Lahteine	f2301a2a04	Add e-stepper count to EEPROM (for planner vars)	2016-12-09 06:05:31 -08:00
Scott Lahteine	53c9fca0f6	Only write to EEPROM when a byte changes	2016-12-09 06:05:31 -08:00
AnHardt	13eebd11cf	volatile_block_buffer_runtime_us `block_buffer_runtime_us` is mangled in the planner and in the stepper-ISR. So it needs to be volatile and interrupt protected.	2016-12-09 14:49:02 +01:00
Scott Lahteine	8383f35b40	Merge pull request #5445 from thinkyhead/rc_reduce_jerk_code Slightly shrink jerk and advance code	2016-12-09 02:54:03 -08:00
Gege2B	40453c1b9a	Update french translation (LIGHTS str)	2016-12-09 11:18:29 +01:00
Scott Lahteine	fc2fc828b3	Prettify LIN_ADVANCE code with the positive condition	2016-12-09 00:29:07 -08:00
Scott Lahteine	1929502e15	Add const to some variables	2016-12-09 00:29:06 -08:00
Scott Lahteine	2da4d22520	Pretty up ADVANCE code	2016-12-08 22:51:28 -08:00
Scott Lahteine	af024e1d7c	Pretty up coast / reverse jerk code	2016-12-08 22:50:25 -08:00
Scott Lahteine	3f3b5c86d8	Slightly shrink code for jerk-based reduction of safe_speed	2016-12-08 22:24:29 -08:00
AnHardt	87fe20b5f5	Simplify long_move() We are not really interested in, if there are blocks. All information we need is in `block_buffer_runtime_us`.	2016-12-09 00:13:35 +01:00
Scott Lahteine	574d9c7d3d	Merge pull request #5432 from Kaibob2/patch-2 Update language_de.h	2016-12-08 13:14:04 -08:00
Scott Lahteine	f089279263	Merge pull request #5431 from esenapaj/Suppress-warnings,-etc Suppress warnings, etc	2016-12-08 13:10:12 -08:00
Scott Lahteine	d92ccb230c	Merge pull request #5438 from AnHardt/patch-long_move Patch long_move()	2016-12-08 13:08:36 -08:00
AnHardt	706b240251	Patch long_move() While the last move in the planner_buffer is running it's duration is already subtracted from block_buffer_runtime_us.	2016-12-08 21:03:26 +01:00
esenapaj	a298a58684	Remove redundant "E"	2016-12-09 02:27:34 +09:00
Kai	390a6d976a	Update language_de.h #define MSG_ENDSTOP_ABORT doesn't fit in Display See https://github.com/MarlinFirmware/Marlin/issues/5401#issuecomment-265714487	2016-12-08 12:18:19 +01:00
esenapaj	e9393c3634	Suppress warnings, etc ・Suppress warnings ・Remove unused variable "did_update"	2016-12-08 17:47:59 +09:00
Scott Lahteine	da6a094424	Sanity-check inverting and pullups for Z probe and Z endstop `Z_MIN_ENDSTOP_INVERTING` must match `Z_MIN_PROBE_ENDSTOP_INVERTING` when using `Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN`. This is easy to overlook.	2016-12-08 00:12:19 -08:00
Scott Lahteine	3fb43c11fc	Fix compile error with LCD_I2C_VIKI	2016-12-07 23:29:45 -06:00
Scott Lahteine	aa241c63b3	Include M205 note in configurations	2016-12-07 14:45:44 -06:00
Scott Lahteine	c8a95ec514	Merge pull request #5413 from MagoKimbra/rc_fix_mesh Fix Mesh without Fade Height	2016-12-07 03:16:02 -06:00
Scott Lahteine	35ad9626f1	Merge pull request #5410 from thinkyhead/rc_polish_update Update Polish language, reduce filament change messages	2016-12-07 03:15:53 -06:00
Scott Lahteine	01e5d46ea7	Patch some planner compile errors	2016-12-07 02:26:24 -06:00
MagoKimbra	5383212a28	Fix Mesh without Fade Height	2016-12-07 09:23:42 +01:00
Scott Lahteine	dbe1dc1452	Merge pull request #5406 from Rigid3D/RCBugFix Turkish Translation Update	2016-12-07 00:56:08 -06:00
Scott Lahteine	4783a59249	Remove filament-change empty lines from languages	2016-12-07 00:53:03 -06:00
Scott Lahteine	1705099c3e	Save space by not defining unused filament change message lines	2016-12-07 00:53:03 -06:00
android444	9b1f4b514b	Update Polish language Translation of messages in English to Polish.	2016-12-06 22:28:33 -06:00
Robert Marko	84f7e1de04	Updates to Croatian language	2016-12-06 22:24:12 -06:00
esenapaj	08cdaaf19b	README and Version for 1.1.0-RCBugFix Sync with RC8	2016-12-07 10:43:58 +09:00
Mehmet Sutas	f4663cb677	Update language_tr_utf8.h	2016-12-07 00:21:56 +03:00
Mehmet Sutas	b4fd115d4e	Update language_tr.h	2016-12-07 00:20:07 +03:00
Scott Lahteine	83c5026db1	Ignore homing button when SD printing As suggested in #5404 by @android444	2016-12-06 14:22:34 -06:00
Scott Lahteine	312caef472	Merge pull request #5398 from thinkyhead/rc_croatian_cleanup Fix Croatian spacing, extra #endif	2016-12-06 03:22:19 -06:00
Scott Lahteine	46b65773ea	Fix Croatian spacing, extra #endif	2016-12-06 03:10:37 -06:00
Scott Lahteine	3f2faac9d1	Merge pull request #5388 from thinkyhead/rc_subdivide_bilinear Subdivide Bilinear Grid with Catmull Rom Splines	2016-12-05 20:28:50 -06:00
Scott Lahteine	b5b5edd9ad	Merge pull request #5394 from thinkyhead/rc_drop_board_99 Remove mystery-board 99	2016-12-05 20:28:35 -06:00
Scott Lahteine	c48901f355	Remove mystery-board 99	2016-12-05 20:16:50 -06:00
akaJes	d7b948610a	Experimental bilinear subdivision option	2016-12-05 20:11:24 -06:00
Scott Lahteine	6253b765aa	Merge pull request #5389 from thinkyhead/distribute_screen_updates Distribute GLCD screen updates in time	2016-12-05 20:08:33 -06:00
Scott Lahteine	b203901143	Merge pull request #5393 from AnHardt/Fix-auto_report_temperatures Fix auto_report_temperatures()	2016-12-05 19:38:23 -06:00
AnHardt	59a27ed27d	Fix auto_report_temperatures() The `auto_report_temperatures` needs a linefeed to be recognized by Repetier Host.	2016-12-06 01:26:44 +01:00
AnHardt	a6fbd4a5d8	Distribute GLCD screen updates in time Currently we draw and send the screens for a graphical LCD all at once. We draw in two or four parts but draw them directly behind each other. For the tested status screen this takes 59-62ms in a single block. During this time nothing else (except the interrupts) can be done. When printing a sequence of very short moves the buffer drains - sometimes until it's empty. This PR splits the screen update into parts. Currently we have 10 time slots. During the first one the complete screen is drawn. (60,0,0,0,0,0,0,0,0,0,0) Here i introduce pauses for doing other things. (30,30,0,0,0,0,0,0) or (15,15,15,15,0,0,0,0,0,0) Drawing in consecutive time slots prevents from lagging too much. Even with a 4 stripe display all the drawing is done after 400ms. Previous experiments with a even better distribution of the time slots like (30,0,0,0,0,30,0,0,0,0) and (15,0,15,0,15,0,15,0,0,0) did not feel good when using the menu, because of too much lag. Because of the previous PRs to speed up the display updates and especially reducing the difference between drawing 2 or 4 stripes, it now makes sense for the REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER to go from 2 to 4 stripes. This costs about 1-2ms per complete screen update, but is payed back by having partial updates lasting only the half time and two additional brakes. Also ~256 byte of framebuffer are saved in RAM. 13:45:59.213 : echo: #:17 >:13 s:30; #:16 >:13 s:29; S#:33 S>:26 S:59 13:46:00.213 : echo: #:16 >:14 s:30; #:17 >:13 s:30; S#:33 S>:27 S:60 13:46:01.215 : echo: #:17 >:13 s:30; #:16 >:13 s:29; S#:33 S>:26 S:59 13:46:02.215 : echo: #:16 >:13 s:29; #:16 >:14 s:30; S#:32 S>:27 S:59 13:46:03.214 : echo: #:17 >:13 s:30; #:17 >:13 s:30; S#:34 S>:26 S:60 13:46:04.214 : echo: #:16 >:13 s:29; #:16 >:14 s:30; S#:32 S>:27 S:59 13:46:05.212 : echo: #:16 >:14 s:30; #:17 >:13 s:30; S#:33 S>:27 S:60 13:46:06.212 : echo: #:17 >:13 s:30; #:16 >:13 s:29; S#:33 S>:26 S:59 03:30:36.779 : echo: #:8 >:7 s:15; #:10 >:7 s:17; #:8 >:6 s:14; #:8 >:7 s:15; S#:34 S>:27 S:61 03:30:37.778 : echo: #:8 >:6 s:14; #:10 >:7 s:17; #:9 >:7 s:16; #:8 >:6 s:14; S#:35 S>:26 S:61 03:30:38.778 : echo: #:8 >:6 s:14; #:11 >:7 s:18; #:8 >:6 s:14; #:8 >:7 s:15; S#:35 S>:26 S:61 03:30:39.777 : echo: #:8 >:6 s:14; #:10 >:7 s:17; #:8 >:8 s:16; #:8 >:6 s:14; S#:34 S>:27 S:61 03:30:40.780 : echo: #:8 >:6 s:14; #:11 >:7 s:18; #:8 >:6 s:14; #:8 >:6 s:14; S#:35 S>:25 S:60 03:30:41.780 : echo: #:9 >:6 s:15; #:10 >:7 s:17; #:8 >:6 s:14; #:9 >:6 s:15; S#:36 S>:25 S:61 03:30:42.779 : echo: #:8 >:6 s:14; #:10 >:8 s:18; #:8 >:6 s:14; #:8 >:6 s:14; S#:34 S>:26 S:60 03:30:43.778 : echo: #:9 >:6 s:15; #:10 >:7 s:17; #:8 >:7 s:15; #:9 >:6 s:15; S#:36 S>:26 S:62 #: draw a stripe >: transfer a stripe s: sum of of draw and transfer for one stripe S#: sum of draws for a complete screen S>: sum of transfers for a complete screen S: time to draw and transfer a complete screen	2016-12-05 12:22:54 -06:00
Scott Lahteine	f882355994	Merge pull request #5318 from Sebastianv650/Account_for_LCD_improvements Account for LCD improvements in ENSURE_SMOOTH_MOVES	2016-12-05 11:23:58 -06:00
Scott Lahteine	20e834461d	Merge pull request #5385 from thinkyhead/rc_ftostr4sign_decimal Show decimal for small numbers in ftostr4sign	2016-12-05 11:22:45 -06:00
Scott Lahteine	b6b100c471	Merge pull request #5371 from thinkyhead/rc_extruders_can_differ Allow distinct factors for multiple extruders	2016-12-05 11:22:31 -06:00
Scott Lahteine	449d9cbf60	Add placeholders for Polish translatable strings	2016-12-05 10:37:00 -06:00
c64pl	643dc4b64e	Update language_pl.h Fixed translations	2016-12-05 10:37:00 -06:00
Scott Lahteine	0974b75fb6	Merge pull request #5386 from thinkyhead/rc_galician_update Galician language update.	2016-12-05 10:36:26 -06:00
Rafa Couto	2b9115330d	Galician language update.	2016-12-05 10:11:28 -06:00
Scott Lahteine	1f3e2440bc	Merge pull request #5175 from thinkyhead/rc_dualx_homing Unpark when using Z_SAFE_HOMING with Dual X	2016-12-05 10:02:56 -06:00
Scott Lahteine	d5bf1684fe	Implement as optional feature LCD_DECIMAL_SMALL_XY And reduce the function size to simplify	2016-12-05 09:26:05 -06:00
Guthenberg	bfb8d3b53e	Show more decimals in Display, if possible _123, -123, _-12, __-1 plus 1234, 12.3, -1.2	2016-12-05 09:05:46 -06:00
Scott Lahteine	1e30d1da47	Simplify itostr4sign - This function becomes obsolete if ftostr4sign is re-written.	2016-12-05 09:05:46 -06:00
Scott Lahteine	82a187acae	Merge pull request #5359 from AnHardt/update-de Add missing translations to lang-de	2016-12-05 07:31:28 -06:00
Scott Lahteine	4bafdf4b66	Support DISTINCT_E_FACTORS in LCD Motion Menu	2016-12-05 07:26:18 -06:00
Scott Lahteine	3391c785c6	Support for distinct E factors	2016-12-05 07:26:18 -06:00
Scott Lahteine	0dfe95eaba	Adjust formatting in Planner	2016-12-05 07:26:17 -06:00
Scott Lahteine	09587f7c0d	Fix rows error in DOGM	2016-12-05 07:14:11 -06:00
Scott Lahteine	c47e07d129	Fix Dual X software endstops	2016-12-05 06:51:41 -06:00
Scott Lahteine	4217e9653e	Adjust park code in tool_change	2016-12-05 06:51:41 -06:00
Scott Lahteine	b20405db31	Only DXC_AUTO_PARK_MODE should auto-move in tool_change	2016-12-05 06:48:43 -06:00
Scott Lahteine	ca24af7d5d	Dual X with home_z_safely is not parked	2016-12-05 06:43:26 -06:00
Scott Lahteine	0e15b4f434	Dual X set_axis_is_at_home can use x_home_pos for both	2016-12-05 06:43:26 -06:00
Scott Lahteine	54109dfaec	Reduce code size for Dual X un-park	2016-12-05 06:43:26 -06:00
Scott Lahteine	fe96f74db1	Use const arguments in Dual X helper functions	2016-12-05 06:43:26 -06:00
Scott Lahteine	41278c1e8b	Apply LOGICAL_POSITION to home positions on Dual X	2016-12-05 06:43:26 -06:00
Scott Lahteine	053fb55af6	Fix modes ordering in prepare_move_to_destination_dualx	2016-12-05 06:43:26 -06:00
Scott Lahteine	ee50928eee	Make LOGICAL and RAW position macros ternary-compatible	2016-12-05 06:43:26 -06:00
Scott Lahteine	56dd15c0ad	Use SET_INPUT for PS_ON_PIN in kill	2016-12-05 06:43:26 -06:00
Scott Lahteine	200cf3e9f9	Merge pull request #5381 from thinkyhead/rc_fix_fade_factor Properly apply fade_factor to MBL	2016-12-05 06:06:13 -06:00
Scott Lahteine	84ff78c1e3	Pass the fade factor to mbl.get_z	2016-12-05 03:01:51 -06:00
Scott Lahteine	85c2b96685	Apply const to MBL class methods	2016-12-05 02:50:59 -06:00
Scott Lahteine	c06161b773	Use apply_leveling, not MBL directly	2016-12-05 01:53:36 -06:00
Scott Lahteine	818f8b93d3	Merge pull request #5378 from thinkyhead/rc_duration_rj Better alignment of elapsed print time	2016-12-04 22:42:23 -06:00
Scott Lahteine	9d88a61d52	Better alignment of elapsed print time	2016-12-04 21:30:49 -06:00
Scott Lahteine	0b53d78046	Tweak editable items for debugging	2016-12-04 03:51:10 -06:00
Scott Lahteine	fccc97de6d	Save PROGMEM with string changes Unlike RAM-based strings, PROGMEM strings aren’t consolidated by the compiler.	2016-12-03 19:21:46 -06:00
AnHardt	e7fc353f08	Add missing translations to lang-de	2016-12-03 20:51:49 +01:00
Scott Lahteine	3f2cb376e0	Add placeholders for Bulgarian translation	2016-12-03 12:14:02 -06:00
Scott Lahteine	b22d37ba52	Merge pull request #5364 from thinkyhead/rc_croatian_update Update Croatian to include missing strings	2016-12-03 11:37:42 -06:00
Robert Marko	b796a687ca	Update Croatian to include missing strings Added all missing strings according to English	2016-12-03 11:15:41 -06:00
Scott Lahteine	255ed80164	Fix hotend offset report in M503	2016-12-03 10:17:35 -06:00
Petr Zahradník	c66f3ed34b	Update Czech	2016-12-03 10:32:34 +01:00
Scott Lahteine	cbf208ea1f	Merge pull request #5348 from Kaibob2/patch-1 Update language_de.h	2016-12-03 01:53:24 -06:00
Scott Lahteine	a2660cf688	Merge pull request #5347 from tnw513/fix-italian Added missing translations	2016-12-03 01:52:45 -06:00
Scott Lahteine	27dd5acc22	Fix set_led_color for BLINKM Follow-up to #5330	2016-12-03 01:51:11 -06:00
Kai	8530c32309	Update language_de.h Grammar corrections	2016-12-02 19:40:36 +01:00
Silvio Didonna	f1d5ffa211	Added missing translations	2016-12-02 18:49:39 +01:00
Scott Lahteine	b0361ebe4f	Merge pull request #5343 from thinkyhead/rc_invert_case_light Allow case light pin to be active low	2016-12-02 01:17:11 -06:00
Scott Lahteine	f60b4f8659	Allow case light pin to be active low	2016-12-01 23:32:34 -06:00
Scott Lahteine	3f4c02e42f	Merge pull request #5259 from Sebastianv650/Allow_UART-ISR_inside_Stepper Allow UART ISRs inside the stepper ISR	2016-12-01 23:17:42 -06:00
Scott Lahteine	d07229f185	Fix redraw in SD Card menus	2016-12-01 18:15:58 -06:00
Scott Lahteine	47b4b21308	Merge pull request #5331 from esenapaj/Fix-for-the-PR-#5072 Fix for the PR #5072 (Add predefined AUTO_FAN_PINs to pins files), etc	2016-12-01 13:37:02 -06:00
Scott Lahteine	8d14420331	Fix compile without ENABLE_LEVELING_FADE_HEIGHT	2016-12-01 11:37:24 -06:00
Scott Lahteine	415294801f	Merge pull request #5330 from thinkyhead/rc_rgb_led Support for an RGB LED using 3 pins	2016-11-30 14:14:00 -06:00
esenapaj	0909cf3d46	Adjust spacing	2016-11-30 19:39:39 +09:00
esenapaj	8e9e9c17b0	Follow-up the PR #5323 (Adding ukrainian language support) ・Update forgotten Configuration_adv.h of Felix\DUAL and K8400\Dual-head	2016-11-30 19:39:39 +09:00
esenapaj	d92ce8849b	Fix for the PR #5072 (Add predefined AUTO_FAN_PINs to pins files), etc ・Make descriptions the same as others	2016-11-30 19:39:38 +09:00
Scott Lahteine	e00b380489	Merge pull request #5323 from akaJes/lang-ua Adding ukrainian language support	2016-11-30 01:10:40 -06:00
Scott Lahteine	65c50e062e	Support for an RGB LED using 3 pins	2016-11-30 00:02:31 -06:00
esenapaj	3047f3c85c	Suppress warning	2016-11-30 00:32:56 +09:00
jes	f674246397	extend Configurations files	2016-11-29 15:04:36 +02:00
jes	c90191faaf	adding ukrainian laguage support	2016-11-29 14:49:45 +02:00
Sebastianv650	912704a0d8	Enable ISRs inside temperature ISR to capture chars at UART at 250000 baud.	2016-11-28 20:08:50 +01:00
Sebastianv650	f62f4006af	Account for LCD improvements in ENSURE_SMOOTH_MOVES .. and give the hint to try lower values if possible.	2016-11-28 17:44:19 +01:00
Scott Lahteine	092e949b58	Merge pull request #5169 from thinkyhead/rc_core_inverted Support for COREYX, COREZX, COREZY	2016-11-28 02:26:41 -06:00
Scott Lahteine	e9e4208ff1	Merge pull request #5274 from Sebastianv650/improve_smooth_moves Improvement for ENSURE_SMOOTH_MOVES	2016-11-28 02:22:08 -06:00
Scott Lahteine	c7935bb0d2	Merge pull request #5299 from thinkyhead/rc_bed_correction_fade Add a fade factor for mesh leveling	2016-11-28 02:07:51 -06:00
Scott Lahteine	a69b1ee691	Merge pull request #5313 from thinkyhead/rc_fix_menu_actions Keep drawing menu unless screen changes	2016-11-28 02:01:39 -06:00
Scott Lahteine	32ee3acf86	Merge pull request #5315 from thinkyhead/rc_fixup_material_menus Refine material heatup menu items	2016-11-28 01:46:51 -06:00
Scott Lahteine	c70a06daf1	lcd_save_previous_menu => lcd_save_previous_screen	2016-11-28 01:46:18 -06:00
Scott Lahteine	13ea43cc8d	Only exit menu handler when the screen changes	2016-11-28 01:46:18 -06:00
Scott Lahteine	f45b6a7762	Merge pull request #5314 from thinkyhead/case_light_menu_fix Fix and optimize case-light code	2016-11-28 01:45:27 -06:00
Scott Lahteine	59fafb93b2	Merge pull request #5304 from AnHardt/pixel-shifting MENU_HOLLOW_FRAME for the menu screens	2016-11-28 01:41:47 -06:00
Scott Lahteine	0951d385ce	Don't set heater temperature above its maximum	2016-11-28 01:37:24 -06:00
Scott Lahteine	c9193e856d	Limit preheat parameters based on all nozzles	2016-11-28 01:37:24 -06:00
Scott Lahteine	bb4529f7d2	PLA / ABS => Material 1 / 2	2016-11-28 01:37:24 -06:00
Scott Lahteine	61437d988a	Fix and optimize case-light code	2016-11-28 01:34:52 -06:00
AnHardt	7a9fa78822	MENU_HOLLOW_FRAME for the menu screens MENU_HOLLOW_FRAME for the menu screens and some pixel shifting to optimize the look with tall fonts. (cn)	2016-11-27 22:59:05 +01:00
AnHardt	24ca1a6289	Not more then 4 stripes for u8g-devices To optimise speed. Costs well invested 128Byte of RAM.	2016-11-26 19:08:33 +01:00
Scott Lahteine	aee71c543e	Minor formatting in language.h	2016-11-26 06:53:52 -06:00
Scott Lahteine	05d8d189f6	Adjust spacing in utf_mapper.h	2016-11-26 06:53:52 -06:00
Scott Lahteine	5460a529da	Add option DOGM_SPI_DELAY_US	2016-11-26 06:53:52 -06:00
Scott Lahteine	71842b6a17	Apply const to LCD arguments and locals	2016-11-26 06:53:52 -06:00
Scott Lahteine	b1abd7edef	Optimize graphical display with selective rendering	2016-11-26 06:53:52 -06:00
AnHardt	b91fab2d7d	Fix USE_BIG_EDIT_FONT	2016-11-26 13:50:25 +01:00
Scott Lahteine	4cd73e183d	Hide hidden files and folders	2016-11-26 06:26:28 -06:00
Scott Lahteine	f6f77d34a1	Add a fade factor for mesh leveling	2016-11-26 03:41:26 -06:00
AnHardt	75fdcc14b7	Activate font and mapper for el-gr	2016-11-26 02:30:37 +01:00
AnHardt	a0004e7cd3	Change font decent to -1 for tt and gr For speeding up font drawing unify font decent. Tr and Gr have ben the only fonts with a font decent of -2. Sorry for some, a bit compressd, but hopefully still readeble symbols.	2016-11-26 02:29:23 +01:00
Scott Lahteine	307f263f89	Merge pull request #5292 from esenapaj/Update-Japanese-translation Update Japanese translation	2016-11-25 16:56:49 -06:00
esenapaj	7070143042	Update Japanese translation ・Add new translation	2016-11-24 21:10:40 +09:00
esenapaj	ef97645002	Follow-up the PR #5255 (Case light menu (3rd attempt))	2016-11-24 19:42:05 +09:00
Scott Lahteine	2a9b3376a9	Merge pull request #5289 from thinkyhead/rc_which_menu_actions Drop "static" keyword in ultralcd.cpp function declarations	2016-11-23 23:04:05 -06:00
Scott Lahteine	b97dafe4b8	Drop "static" keyword in ultralcd.cpp function declarations	2016-11-23 20:43:01 -06:00
Scott Lahteine	2e966f8e5b	Patch Capabilities Report for "PROGRESS"	2016-11-23 19:31:46 -06:00
Scott Lahteine	f60321d3e3	Merge pull request #5284 from thinkyhead/rc_turkish_update Turkish update (squashed)	2016-11-23 14:57:52 -06:00
Mehmet Sutas	a26668b10c	Add UTF8 Turkish Translation	2016-11-23 14:19:16 -06:00
Mehmet Sutas	61aa796307	Added Human Readable Comments	2016-11-23 14:19:16 -06:00
Mehmet Sutas	6fb9c6fe07	Follow-up for #5167 Turkish Language Add check for Turkish Font before setting better font for graphic displays	2016-11-23 14:19:15 -06:00
Scott Lahteine	d891324830	Merge pull request #5258 from mosh1/mbl_speed_fix Fix z feedrate value when doing mesh bed leveling. probe feedrate use…	2016-11-23 14:15:01 -06:00
Scott Lahteine	7f8133a51f	Merge pull request #5255 from Kaibob2/CaseLightMenu Case light menu (3rd attempt)	2016-11-23 13:46:33 -06:00
Kai	e9b42f4f47	Update language_de.h	2016-11-23 19:29:19 +01:00
Kai	0c341f0c50	Added Menu entry for Case light	2016-11-23 19:29:15 +01:00
Scott Lahteine	3bc2273ac9	Comment M540	2016-11-21 18:08:00 -06:00
Scott Lahteine	14b74181f5	Merge pull request #5179 from thinkyhead/rc_TMC2130 TMC2130 "Silent StepStick" support	2016-11-21 14:10:52 -06:00
Scott Lahteine	bb2114a060	Merge pull request #5264 from thinkyhead/rc_delta_safe_zone Add an option for delta to home to the top	2016-11-21 13:56:44 -06:00
Scott Lahteine	38466b1d2f	Merge pull request #5271 from esenapaj/Fix-for-the-PR-#5267 Fix for thePR #5267 (Introduce a +1234.56 format for over 999 steps/mm)	2016-11-21 13:55:56 -06:00
Scott Lahteine	9b96a4a53b	Merge pull request #5246 from thinkyhead/rc_some_cleanup Minor stepper cleanup	2016-11-21 13:55:25 -06:00
Sebastianv650	8190483eeb	Improvement for ENSURE_SMOOTH_MOVES Instead of waiting for a single long block, compare the complete block buffer runtime for the long_move() check.	2016-11-21 17:58:24 +01:00
esenapaj	da67037550	Fix for thePR #5267 (Introduce a +1234.56 format for over 999 steps/mm) ・Fix memory leak	2016-11-21 22:31:01 +09:00
Scott Lahteine	0f891e848b	Merge pull request #5268 from esenapaj/Update-Japanese-translation Update Japanese translation	2016-11-21 03:18:36 -06:00
esenapaj	190a04c467	Update Japanese translation ・Change translation for 16 width LCD	2016-11-21 17:51:43 +09:00
esenapaj	7b836a4000	Introduce a +1234.56 format for over 999 steps/mm	2016-11-21 17:45:07 +09:00
Scott Lahteine	3e0376b45e	Reorder M114 and M119 gcode cases	2016-11-21 00:52:19 -06:00
Scott Lahteine	644fac5d34	Reduce all stepper_indirection init code with macros	2016-11-21 00:52:18 -06:00
Scott Lahteine	4e4f37b6c2	Code formatting for TMC and L6470 config options	2016-11-21 00:52:18 -06:00
Scott Lahteine	127e21ae00	Extend M122 for all steppers	2016-11-21 00:52:18 -06:00
Scott Lahteine	bf5f5f44cc	Make TMC2130 init code auto-configure Simply apply enabled settings instead of requiring users to edit stepper_indirection.cpp	2016-11-21 00:52:17 -06:00
Moritz	d67c1d825f	Add TMC2130 support	2016-11-21 00:17:45 -06:00
Scott Lahteine	11effeee2c	Add an option for delta to home to the top	2016-11-20 23:12:07 -06:00
Sebastianv650	50059690e0	Allow UART ISRs inside the stepper ISR If the stepper ISR takes too long, chars are lost which leads to serial communication errors like "Line number not +1" or "Wrong checksum". In worst case, the printer can even do crazy moves. With this changes, UART interrupts are handled inside the stepper ISR. This way, no chars should be lost.	2016-11-20 13:09:12 +01:00
Moshen Chan	29b174bfb9	Fix z feedrate value when doing mesh bed leveling. probe feedrate uses XY_PROBE_SPEED	2016-11-19 16:34:41 -08:00
AnHardt	88b38eafd8	Endstop interrupt refinement At the start of a move, check if the endstops are already triggered. The 'change' interrupts will not see a change if already triggered.	2016-11-19 13:30:49 +01:00
Scott Lahteine	79c8591192	Merge pull request #5253 from thinkyhead/rc_smooth_move_ex-lax Ensure smooth print moves even with LCD enabled	2016-11-19 01:38:41 -06:00
Scott Lahteine	0215cacb30	Merge pull request #5247 from esenapaj/Re-follow-the-PR-#4634 Re-follow the PR #4634 (Set language display charset in language.h)	2016-11-19 01:32:40 -06:00
Scott Lahteine	2cc32d85a3	Adjust ENSURE_SMOOTH_MOVES coding style	2016-11-19 01:28:48 -06:00
Scott Lahteine	072541f286	Update ENSURE_SMOOTH_MOVES in all configs	2016-11-19 01:28:47 -06:00
Sebastianv650	de89dc9f04	Ensure smooth print moves even with LCD enabled lcd_update can take so much time that the block buffer gets drained if there are only short segments. This leads to jerky printer movements for example in circles and a bad print quality. This change implements a simple check: Only if the block currently executed is long enough, run lcd_update. This also means the printer will not show actual values on the LCD nor will it respond to buttons pressed. A option that keeps the menu accessible is also available. Aditionaly, slow down if a block would be so fast that adding a new block to the buffer would take more time. In this case, the buffer would drain until it's empty in worst case.	2016-11-19 01:28:47 -06:00
Scott Lahteine	87b6b19256	Patch CASE_LIGHT typo	2016-11-18 23:49:12 -06:00
Scott Lahteine	0be6167f14	Merge pull request #5250 from CONSULitAS/RCBugFix_K8200_backinsync_2016-11-18 K8200: Example configuration back in sync	2016-11-18 22:49:18 -06:00
Scott Lahteine	eb714ee873	Move dummy thermistor opts, fix redundant sensor comment	2016-11-18 22:24:48 -06:00
Scott Lahteine	7a99c6ce4f	Reformat temp sensor listing	2016-11-18 22:24:47 -06:00
Scott Lahteine	181cdb3cfe	Move GCode list above include lines	2016-11-18 22:24:46 -06:00
Scott Lahteine	25d0c167bd	More detailed static_assert messages	2016-11-18 22:24:46 -06:00
Scott Lahteine	eb120e518c	Followup to new endstop interrupts feature - Fix typos, verbiage - Fix naming of `setup_endstop_interrupts` - Some formatting, indentation, spacing	2016-11-18 21:53:45 -06:00
Scott Lahteine	832fe284b4	Merge pull request #5184 from AnHardt/endstop_interrupts Introduce endstop interrupts	2016-11-18 20:50:24 -06:00
CONSULitAS	cbae44df64	K8200: Example configuration back in sync Configuration.h: back in sync, new features configured Configuration_adv.h: back in sync, new features configured README.md: text updated	2016-11-18 22:55:02 +01:00
esenapaj	5db3738fe7	Re-follow the PR #4634 (Set language display charset in language.h)	2016-11-18 17:44:49 +09:00
Scott Lahteine	6eb6f12c64	Patch up some language formatting	2016-11-18 01:16:58 -06:00
Bo Herrmannsen	8cffa60cc5	Update to Danish language 10/11-2016	2016-11-18 01:16:57 -06:00
Scott Lahteine	98600e1433	Minor stepper cleanup	2016-11-18 01:15:57 -06:00
Florian Heilmann	d08867986e	Add autotemp capabilities to M104 This allows M104 to pass the F and B parameters to enable autotemp as well	2016-11-17 11:28:19 -06:00
Sebastianv650	c11b2bb777	Bugfix LIN_ADV Advance has nothing todo with Z_AXIS, strange copy&paste error?	2016-11-17 11:28:19 -06:00
Scott Lahteine	ee0765e872	Merge pull request #5233 from esenapaj/Update-Japanese-translation Update Japanese translation	2016-11-17 03:38:19 -06:00
Scott Lahteine	2330619da0	Merge pull request #5191 from petrzjunior/const Replace const bool with #define for consistency	2016-11-17 03:37:32 -06:00
esenapaj	b278b7a395	Update Japanese translation Only adjust spacing	2016-11-17 09:05:51 +09:00
Petr Zahradník junior	d7ce5d271b	Replace const bool with #define for consistency	2016-11-16 18:55:21 +01:00
Scott Lahteine	d63230d73e	Merge pull request #5192 from Kaibob2/patch-7 Printer Stats / Completed prints line doesn't fit in display (when german)	2016-11-16 00:16:36 -06:00
Scott Lahteine	548b45026d	Merge pull request #5214 from Sebastianv650/RCBugFix_planner_opt Save some cycle inside the planner	2016-11-16 00:06:55 -06:00
Scott Lahteine	5d23e52d75	Merge pull request #5228 from thinkyhead/rc_keep_last_mix Fix DIRECT_MIXING_IN_G1 to preserve the previous mix	2016-11-15 19:12:01 -06:00
Scott Lahteine	db47aa983d	Merge pull request #5226 from mtowara/RCBugFix bump -std in Makefile to c++11	2016-11-15 16:13:32 -06:00
Scott Lahteine	99b0c1fe56	Fix DIRECT_MIXING_IN_G1 to preserve the previous mix	2016-11-15 16:12:26 -06:00
Markus Towara	23a675f621	reduce binary size of .hex still a few bytes bigger than with arduino but nothing major	2016-11-15 21:57:15 +01:00
Markus Towara	5b6e2cecf5	bump c/c++ standard to gnu11 needed for constexpr	2016-11-15 21:54:12 +01:00
Scott Lahteine	410657b050	Fix G30 with limits, print correct probe XY	2016-11-15 14:10:28 -06:00
AnHardt	f3eee02596	Introduce endstop interrupts If ENDSTOP_INTERRUPTS_FEATURE is enabled this tries to set up interrupt routines for all used endstop pins. If this worked without errors, `endstops.update()` is called only if one of the endstops changed its state. The new interrupt routines do not really check the endstops and react upon them. All what they do, is to set a flag if it makes sense to call the endstop test we are used to. This can be used on: * ARM (DUE) based boards - all pins can raise interrupts, * RAMPS - all 6 endstop pins plus some other on EXT-2 can raise interrupts, * RAMPS based boards - as long the designers did not change the pins for the endstops or at least left enough, * all boards, if there are enough pins that can raise interrupts, and you are willing/able to swap with pins dedicated to other purpose.	2016-11-15 12:07:41 +01:00
Sebastianv650	e3ffb58fbd	Save some cycle inside the planner planner.h: fan speed is used to set integer variables, so no need for long. Basicaly a byte should be enough for all the fan things, as it's 0-255? planner.cpp: Save some float multiplications. We could squeeze out even more by defining feedrate_percentage, saved_feedrate_percentage and flow_percentage as float instead of int. Everytime they are used in the time-critical planner, they are casted to float and multiplied by 0.01. Not done jet, as they are used in LCD menu functions I don't know well enough.	2016-11-13 13:34:12 +01:00
Scott Lahteine	665b7f3893	Merge pull request #5212 from thinkyhead/rc_mixing_faster Store mix factors as reciprocals and multiply	2016-11-12 18:47:11 -06:00
Scott Lahteine	60cc9342a4	Merge pull request #5188 from thinkyhead/rc_extended_host_support Extended host support: M155 Auto temp report, M115 capabilities	2016-11-12 15:38:06 -06:00
Scott Lahteine	f663220e87	Store Mix factors as reciprocals and multiply	2016-11-12 15:19:18 -06:00
Scott Lahteine	ea3c08d249	Merge pull request #5186 from esenapaj/Follow-up-the-PR-#5167-etc Follow up the PR #5167 (Add Turkish Language) again, etc	2016-11-12 13:11:54 -06:00
Scott Lahteine	c488378532	Merge pull request #5205 from Sebastianv650/RCBugFix_stepperpatch Remove useless line from stepper ISR	2016-11-12 12:43:07 -06:00
Michael Neumann	8bdf303da0	Update pins_MEGATRONICS_3.h	2016-11-12 12:26:07 +01:00
Michael Neumann	3890366c83	Update pins.h	2016-11-12 12:25:45 +01:00
Michael Neumann	c0d45ca7f2	Update boards.h	2016-11-12 12:24:47 +01:00
Sebastianv650	cdc18f8c22	Remove useless line from stepper ISR The flag is already set inside planner.get_current_block(). Doing it twice isn't making it better..	2016-11-11 19:35:03 +01:00
Kai	8e8b4398f3	Printer Stats / Completed prints line doesn't fit in display (when german)	2016-11-09 22:03:25 +01:00
Scott Lahteine	b31a07e261	Stateful M355 with separate P parameter	2016-11-09 03:28:18 -06:00
Scott Lahteine	3c9a838651	Extended capabilities report in M115	2016-11-09 02:32:58 -06:00
Scott Lahteine	68b866b5dd	Add M155 - Auto-report temperature with interval	2016-11-09 02:32:58 -06:00
Scott Lahteine	68b46fb2c9	Allow send to i2c address 0 (broadcast)	2016-11-08 17:54:55 -06:00
Scott Lahteine	75bfde9945	M155=>M260, M156=>M261	2016-11-08 17:54:54 -06:00
esenapaj	2ae72b0491	Follow up the PR #5167 (Add Turkish Language) again, etc ・Update forgotten K8400\Dual-head\Configuration.h ・Adjust spacing	2016-11-09 06:31:21 +09:00
Scott Lahteine	06f2282f82	Merge pull request #5176 from thinkyhead/rc_filchange_feedback Give instant feedback for filament change	2016-11-07 12:11:54 -06:00
Scott Lahteine	dcfd7c69e8	Merge pull request #5163 from nzinov/RCBugFix Improve G30 probing command - add optional arguments	2016-11-07 11:37:13 -06:00
Scott Lahteine	e765eebfb0	Patch spacing in bilinear grid report	2016-11-07 04:08:25 -06:00
Scott Lahteine	7780052fb3	Give instant feedback for filament change	2016-11-07 03:48:16 -06:00
esenapaj	24e3f7abe7	Update Turkish translation ・Add new translation	2016-11-07 04:59:18 +09:00
esenapaj	be48792e9c	Follow up the PR #5167 (Add Turkish Language), etc ・Remove all the #ifndef ・Follow the PR #4603 (Strip never-translated strings from language files) ・Follow the PR #4634 (Set language display charset in language.h) ・Follow the PR #4936 (Put max_jerk vars in array, clean up jerk code) ・Adjust spacing	2016-11-06 23:59:02 +09:00
Scott Lahteine	1864b282c5	Implement reversed CORE options	2016-11-05 23:47:51 -05:00
Scott Lahteine	e3c8318504	Add reversed CORE options	2016-11-05 23:47:46 -05:00
Rigid3D	2327764980	Add Turkish Language	2016-11-05 21:06:16 -05:00
Nikolay Zinov	dea00bbcf1	improve G30 probing Add optional parameters X, Y for probe point S sets stowing on and off	2016-11-05 13:22:45 +03:00
Scott Lahteine	00662b8635	Minor babystep cleanup patches	2016-11-03 23:31:45 -05:00
Scott Lahteine	cad792e702	Reduce code for invariant lcd_detected	2016-11-03 23:31:45 -05:00
Scott Lahteine	b23d255491	Move macros above Stepper::babystep	2016-11-03 23:31:45 -05:00
Scott Lahteine	cc57d46158	Fix set_position for CoreYZ	2016-11-03 23:31:45 -05:00
Scott Lahteine	0269347682	Merge pull request #5141 from thinkyhead/rc_old_slowdown_what OLD_SLOWDOWN does nothing, so remove it	2016-11-03 23:30:43 -05:00
Scott Lahteine	e92e2b2446	Merge pull request #5144 from Sebastianv650/RCBugFix_LIN_ADV_wipe Account for wipe moves	2016-11-03 23:19:25 -05:00
Scott Lahteine	176aeafc19	Don't define bilinear_line_to_destination on kinematic setups	2016-11-03 14:10:07 -05:00
Sebastianv650	d448500643	Account for moves with negative E movements Added a rule so that LIN_ADVANCE isn't used for moves with negative E movements (de_float will be negative in this cases). I also added a more detailed comment to make it more clear what the if statement does.	2016-11-03 17:01:17 +01:00
Scott Lahteine	236853df22	Corrections to bilinear_line_to_destination - Allow more than 9x9 probe points - Account for the probe starting position	2016-11-03 04:43:59 -05:00
Scott Lahteine	0115e495fe	Fix up Dual X switch blocks	2016-11-02 21:38:50 -05:00
Scott Lahteine	2495ab7af2	Make dual_x_carriage_mode an enumeration	2016-11-02 21:38:49 -05:00

... 14 15 16 17 18 ...

6921 commits