Commit graph

568 commits

Author SHA1 Message Date
Sebastianv650 84c685f8b5 First draft of Unified Stepper / E Advance ISR 2016-12-21 01:34:39 -08:00
Scott Lahteine bec30c89e7 Merge pull request #5522 from esenapaj/Add-description-for-dual-x
Add description for choice of DEFAULT_DUAL_X_CARRIAGE_MODE
2016-12-20 01:31:53 -08:00
Scott Lahteine 18ba31e9b5 Add Debug Menu with LCD_PROGRESS_BAR_TEST as an example 2016-12-19 22:57:14 -08:00
esenapaj 6854f44bf2 Add description for choice of DEFAULT_DUAL_X_CARRIAGE_MODE 2016-12-19 02:21:10 +09:00
Scott Lahteine 78d6d6e076 Merge pull request #5452 from thinkyhead/rc_save_your_mesh
Save Bed Leveling to EEPROM
2016-12-15 20:23:01 -08:00
Scott Lahteine 1b2fb2bdc7 ABL_GRID_POINTS_* => ABL_GRID_MAX_POINTS_* 2016-12-15 19:08:41 -08:00
esenapaj 069c6b38dd Remove unnecessary tabs and spaces 2016-12-16 00:21:32 +09:00
Scott Lahteine 06af3b62ba Move HOLLOW_FRAME options to config_adv 2016-12-14 04:31:27 -08:00
AnHardt d0e24e0876 Adaptive screen updates for all kinds of displays
The target here is to update the screens of graphical and char base
displays as fast as possible, without draining the planner buffer too much.

For that measure the time it takes to draw and transfer one
(partial) screen to the display. Build a max. value from that.
Because ther can be large differences, depending on how much the display
updates are interrupted, the max value is decreased by one ms/s. This way
it can shrink again.
On the other side we keep track on how much time it takes to empty the
planner buffer.
Now we draw the next (partial) display update only then, when we do not
drain the planner buffer to much. We draw only when the time in the
buffer is two times larger than a update takes, or the buffer is empty anyway.

When we have begun to draw a screen we do not wait until the next 100ms
time slot comes. We draw the next partial screen as fast as possible, but
give the system a chance to refill the buffers a bit.

When we see, during drawing a screen, the screen contend has changed,
we stop the current draw and begin to draw the new content from the top.
2016-12-13 18:44:34 +01:00
Scott Lahteine 641e0936d4 Patch up Delta Calibration Menu 2016-12-13 02:42:28 -08:00
Scott Lahteine da6a094424 Sanity-check inverting and pullups for Z probe and Z endstop
`Z_MIN_ENDSTOP_INVERTING` must match `Z_MIN_PROBE_ENDSTOP_INVERTING`
when using `Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN`.
This is easy to overlook.
2016-12-08 00:12:19 -08:00
Scott Lahteine aa241c63b3 Include M205 note in configurations 2016-12-07 14:45:44 -06:00
akaJes d7b948610a Experimental bilinear subdivision option 2016-12-05 20:11:24 -06:00
Scott Lahteine f882355994 Merge pull request #5318 from Sebastianv650/Account_for_LCD_improvements
Account for LCD improvements in ENSURE_SMOOTH_MOVES
2016-12-05 11:23:58 -06:00
Scott Lahteine 20e834461d Merge pull request #5385 from thinkyhead/rc_ftostr4sign_decimal
Show decimal for small numbers in ftostr4sign
2016-12-05 11:22:45 -06:00
Scott Lahteine d5bf1684fe Implement as optional feature LCD_DECIMAL_SMALL_XY
And reduce the function size to simplify
2016-12-05 09:26:05 -06:00
Scott Lahteine 3391c785c6 Support for distinct E factors 2016-12-05 07:26:18 -06:00
Scott Lahteine f60b4f8659 Allow case light pin to be active low 2016-12-01 23:32:34 -06:00
Scott Lahteine 47b4b21308 Merge pull request #5331 from esenapaj/Fix-for-the-PR-#5072
Fix for the PR #5072 (Add predefined AUTO_FAN_PINs to pins files), etc
2016-12-01 13:37:02 -06:00
Scott Lahteine 415294801f Merge pull request #5330 from thinkyhead/rc_rgb_led
Support for an RGB LED using 3 pins
2016-11-30 14:14:00 -06:00
esenapaj 0909cf3d46 Adjust spacing 2016-11-30 19:39:39 +09:00
Scott Lahteine 65c50e062e Support for an RGB LED using 3 pins 2016-11-30 00:02:31 -06:00
jes f674246397 extend Configurations files 2016-11-29 15:04:36 +02:00
Sebastianv650 f62f4006af Account for LCD improvements in ENSURE_SMOOTH_MOVES
.. and give the hint to try lower values if possible.
2016-11-28 17:44:19 +01:00
Scott Lahteine 092e949b58 Merge pull request #5169 from thinkyhead/rc_core_inverted
Support for COREYX, COREZX, COREZY
2016-11-28 02:26:41 -06:00
Scott Lahteine c7935bb0d2 Merge pull request #5299 from thinkyhead/rc_bed_correction_fade
Add a fade factor for mesh leveling
2016-11-28 02:07:51 -06:00
Scott Lahteine 5460a529da Add option DOGM_SPI_DELAY_US 2016-11-26 06:53:52 -06:00
Scott Lahteine f6f77d34a1 Add a fade factor for mesh leveling 2016-11-26 03:41:26 -06:00
esenapaj ef97645002 Follow-up the PR #5255 (Case light menu (3rd attempt)) 2016-11-24 19:42:05 +09:00
Scott Lahteine 14b74181f5 Merge pull request #5179 from thinkyhead/rc_TMC2130
TMC2130 "Silent StepStick" support
2016-11-21 14:10:52 -06:00
Scott Lahteine 4e4f37b6c2 Code formatting for TMC and L6470 config options 2016-11-21 00:52:18 -06:00
Scott Lahteine bf5f5f44cc Make TMC2130 init code auto-configure
Simply apply enabled settings instead of requiring users to edit
stepper_indirection.cpp
2016-11-21 00:52:17 -06:00
Moritz d67c1d825f Add TMC2130 support 2016-11-21 00:17:45 -06:00
Scott Lahteine 11effeee2c Add an option for delta to home to the top 2016-11-20 23:12:07 -06:00
Scott Lahteine 072541f286 Update ENSURE_SMOOTH_MOVES in all configs 2016-11-19 01:28:47 -06:00
Scott Lahteine eb714ee873 Move dummy thermistor opts, fix redundant sensor comment 2016-11-18 22:24:48 -06:00
Scott Lahteine 7a99c6ce4f Reformat temp sensor listing 2016-11-18 22:24:47 -06:00
Scott Lahteine eb120e518c Followup to new endstop interrupts feature
- Fix typos, verbiage
- Fix naming of `setup_endstop_interrupts`
- Some formatting, indentation, spacing
2016-11-18 21:53:45 -06:00
Scott Lahteine 832fe284b4 Merge pull request #5184 from AnHardt/endstop_interrupts
Introduce endstop interrupts
2016-11-18 20:50:24 -06:00
Scott Lahteine 2330619da0 Merge pull request #5191 from petrzjunior/const
Replace const bool with #define for consistency
2016-11-17 03:37:32 -06:00
Petr Zahradník junior d7ce5d271b
Replace const bool with #define for consistency 2016-11-16 18:55:21 +01:00
AnHardt f3eee02596 Introduce endstop interrupts
If ENDSTOP_INTERRUPTS_FEATURE is enabled this tries to set up interrupt routines
for all used endstop pins. If this worked without errors, `endstops.update()` is called
only if one of the endstops changed its state.

The new interrupt routines do not really check the endstops and react upon them. All what they
do, is to set a flag if it makes sense to call the endstop test we are used to.

This can be used on:
* ARM (DUE) based boards - all pins can raise interrupts,
* RAMPS - all 6 endstop pins plus some other on EXT-2 can raise interrupts,
* RAMPS based boards - as long the designers did not change the pins for the endstops or at least left enough,
* all boards, if there are enough pins that can raise interrupts, and you are willing/able to swap with pins dedicated to other purpose.
2016-11-15 12:07:41 +01:00
Scott Lahteine 60cc9342a4 Merge pull request #5188 from thinkyhead/rc_extended_host_support
Extended host support: M155 Auto temp report, M115 capabilities
2016-11-12 15:38:06 -06:00
Scott Lahteine 3c9a838651 Extended capabilities report in M115 2016-11-09 02:32:58 -06:00
Scott Lahteine 68b866b5dd Add M155 - Auto-report temperature with interval 2016-11-09 02:32:58 -06:00
Scott Lahteine 75bfde9945 M155=>M260, M156=>M261 2016-11-08 17:54:54 -06:00
esenapaj 2ae72b0491 Follow up the PR #5167 (Add Turkish Language) again, etc
・Update forgotten K8400\Dual-head\Configuration.h
・Adjust spacing
2016-11-09 06:31:21 +09:00
Scott Lahteine e3c8318504 Add reversed CORE options 2016-11-05 23:47:46 -05:00
Rigid3D 2327764980 Add Turkish Language 2016-11-05 21:06:16 -05:00
Scott Lahteine 2495ab7af2 Make dual_x_carriage_mode an enumeration 2016-11-02 21:38:49 -05:00
Stanley ab3f966f5f Case light G-code M355
implemented G-Code M355 into Marlin
2016-11-01 06:30:14 -05:00
Scott Lahteine b6aa894893 Rename auto fan pins and add auto fan flags 2016-10-26 17:51:26 -05:00
Scott Lahteine 627f9d5285 Merge pull request #5056 from thinkyhead/rc_lin_adv_opt
LIN_ADVANCE optimizations
2016-10-22 07:06:39 -05:00
Scott Lahteine 0908329d96 Merge pull request #5057 from thinkyhead/rc_mbl_lcd_logical
Fix manual leveling coordinates
2016-10-22 06:31:02 -05:00
Scott Lahteine 14e60f0d3b Correct typo in configs
As pointed out by #5044
2016-10-22 05:56:32 -05:00
Scott Lahteine b9109b2875 Improve LIN_ADVANCE commentary (all configs) 2016-10-22 05:03:09 -05:00
Scott Lahteine 4f6bfabaad Patch BAUDRATE line in configs 2016-10-22 00:48:52 -05:00
Scott Lahteine b6221df3f3 Merge pull request #4983 from MarlinFirmware/revert-4933-rc_drop_pid_func_range
Revert "Removal of PID functional range"
2016-10-10 13:29:54 -05:00
Scott Lahteine 1e551c0688 Revert "Squashed - Removal of PID functional range" 2016-10-09 16:27:45 -05:00
Scott Lahteine 48761f2021 Patch delta endstop adjustment config 2016-10-09 13:32:45 -05:00
Scott Lahteine 00261cbfcb Merge pull request #4933 from thinkyhead/rc_drop_pid_func_range
Squashed - Removal of PID functional range
2016-10-07 15:07:55 -05:00
Scott Lahteine a0df34fd4c Add PINS_DEBUGGING advanced config option 2016-10-07 14:20:13 -05:00
Rerouter 5f5d87cad3 Update Configuration.h 2016-10-02 07:01:40 -05:00
Scott Lahteine d19cfcfc1d max_jerk array, DEFAULT_XYJERK => DEFAULT_[XY]JERK 2016-10-02 06:34:56 -05:00
Scott Lahteine 473f4a17a8 Merge pull request #4914 from Rerouter/PID-Unconstrained-Itemp
Pid unconstrained itemp
2016-10-01 06:58:07 -05:00
Scott Lahteine 0d538f3db6 Add to all configurations 2016-10-01 05:00:53 -05:00
Scott Lahteine fffc9fefa8 Apply changes to all configs 2016-09-29 02:17:33 -05:00
Scott Lahteine 2d2c9bdf92 Add PROBE_Y_FIRST option for probe order 2016-09-29 02:00:27 -05:00
esenapaj 92c03a44a9 Fix the PR #4899 (ABL: Enable by type. Bilinear for all.) etc.
About Configuration.h:
・Fix the PR #4899 (ABL: Enable by type. Bilinear for all.)
Remove Duplicated contents

・Fix the PR #4305 (Custom boot screen feature improvement)
Revert from "during boot" to "during bootup" in all the example
Configuration.h

・Fix the PR #4207 (Clean up, simplify and generalize the Allen-key-probe
code.)
Resolve and relocate the duplicated definitions in Z_PROBE_ALLEN_KEY
section

・Follow-up the PR #4805 (Additional documentation of Configuration.h)
Add forgotten changes to all the example Configuration.h

Adjust spacing

About Configuration_adv.h:
Add missing description of SLOWDOWN for DELTA

Adjust spacing
2016-09-28 14:14:04 -05:00
Scott Lahteine ea0dbee3c9 Enable ABL by type, support bilinear on cartesian 2016-09-25 23:35:37 -05:00
Scott Lahteine 01f1028510 Try on "CLEARANCE" for size 2016-09-20 18:29:49 -05:00
Scott Lahteine 0e7d638a7a Revert to Probe Raise rather than Probe Height 2016-09-20 18:29:49 -05:00
Scott Lahteine e05af606a8 Clean up probe config options 2016-09-19 00:26:16 -05:00
Scott Lahteine c4dcfa254e Allow override of Z_ENDSTOP_SERVO_NR with BLTOUCH 2016-09-18 22:00:32 -05:00
Scott Lahteine e5505e3b33 Allow non-square leveling grid 2016-09-18 13:11:20 -05:00
Scott Lahteine a1812b55f6 Space out array values 2016-09-16 14:41:05 -05:00
Scott Lahteine d4599fd8ed Comment patches to Configuration.h 2016-09-16 14:41:05 -05:00
Scott Lahteine 723e983073 Default EXTRUDE_MAXLENGTH to 200mm 2016-09-16 14:41:04 -05:00
Scott Lahteine 9b0931ef74 Apply fixed EXTRUDER_RUNOUT_PREVENT 2016-09-13 03:33:04 -05:00
Scott Lahteine a6f6ed352b Fix comment on FILAMENT_RUNOUT_SENSOR 2016-09-13 02:14:34 -05:00
Scott Lahteine aaef7c6b89 Fix a misspelling of minimum 2016-09-02 01:42:38 -05:00
Scott Lahteine f1201e11c7 Improve the Jerk description 2016-08-29 12:39:21 -05:00
Scott Lahteine 3f038bef00 Heading for movement settings 2016-08-29 02:01:34 -05:00
Scott Lahteine 759234af60 MINIMUM_STEPPER_PULSE option 2016-08-27 23:58:40 -05:00
Scott Lahteine ab59280075 MIN_SEGMENTS_FOR_MOVE => MIN_STEPS_PER_SEGMENT
Follow-up to #4666
2016-08-21 08:56:03 -05:00
Scott Lahteine 01d4703429 PREVENT_DANGEROUS_EXTRUDE => PREVENT_COLD_EXTRUSION
Also improve the documentation of this and related options, and set
EXTRUDE_MINTEMP to 170 everywhere.
2016-08-20 23:35:27 -05:00
Scott Lahteine 374f8d2014 dropsegments => MIN_SEGMENTS_FOR_MOVE 2016-08-20 18:52:15 -05:00
Scott Lahteine d63b8e2b2b Additional details for I2C_SLAVE_ADDRESS 2016-08-15 19:27:53 -07:00
Scott Lahteine a99ecf71d8 Add support for i2c slave address 2016-08-10 23:30:35 -07:00
Scott Lahteine e113740fa3 Specify that Z_PROBE_*_HEIGHT is nozzle-relative 2016-08-07 17:54:17 -07:00
Scott Lahteine 7e2bd9a233 Z_RAISE_PROBE_* => Z_PROBE_*_HEIGHT 2016-08-03 21:18:38 -07:00
Scott Lahteine 6eed37aafb Merge pull request #4486 from thinkyhead/rc_pid_add_extrusion_rate_off
PID_EXTRUSION_SCALING, disabled by default
2016-07-31 18:23:51 -07:00
Scott Lahteine 63fd1f49a6 PID_EXTRUSION_SCALING, disabled by default 2016-07-31 17:49:34 -07:00
esenapaj 657ef8aded Follow-up the PR #4408 (Add support for reprapworld LCD), etc
・Put #define REPRAPWORLD_GRAPHICAL_LCD into all the example
configuration files
・Adjust spacing
2016-07-30 20:32:57 +09:00
Scott Lahteine 9e21b2e51d Merge pull request #4455 from AnHardt/double-bump-feature
double bump probing as a feature
2016-07-29 20:00:10 -07:00
AnHardt 7188ce0ad6 double bump probing as a feature
Why double touch probing is not a good thing.

It's widely believed we can get better __probing__ results when using a double touch when probing.

Let's compare to double touch __homing__.
Or better let's begin with single touch __homing__.
We home to find out out position, so our position is unknown.
To find the endstop we have to move into the direction of the endstop.
The maximum way we have to move is a bit longer than the axis length.
When we arrive at the endstop - when it triggers, the stepper pulses are stopped immediately.
It's a sudden stop. No smooth deacceleration is possible.
Depending on the speed and the moving mass we lose steps here.
Only if we approached slow enough (below jerk speed?) we will not lose steps.

Moving a complete axis length, that slow, takes for ever.
To speed up homing, we now make the first approach faster, get a guess about our position,
back up a bit and make a second slower approach to get a exact result without losing steps.

What we do in double touch probing is the same. But the difference here is:
a. we already know where we are
b. if the first approach is to fast we will lose steps here to.
But this time there is no second approach to set the position to 0. We are measuring only.
The lost steps are permanent until we home the next time.

So if you experienced permanently rising values in M48 you now know why. (Too fast, suddenly stopped, first approach)

What can we do to improve probing?
We can use the information about our current position.
We can make a really fast, but deaccelerated, move to a place we know it is a bit before the trigger point.
And then move the rest of the way really slow.
2016-07-30 03:00:49 +02:00
Scott Lahteine c31f56a38c Deprecate EXTRUDER_WATTS and BED_WATTS 2016-07-29 17:34:14 -07:00
Scott Lahteine ea5ac94804 Improved MANUAL_[XYZ]_HOME_POS
No need for `MANUAL_HOME_POSITIONS`. Just set each one as-needed to
override the automatic behavior.
2016-07-28 19:51:48 -07:00
Scott Lahteine 8953e3e984 Allow Z_SAFE_HOMING without a probe 2016-07-27 04:33:56 -07:00
Scott Lahteine 24a1a16e5d Move versioning to MarlinConfig.h 2016-07-26 12:37:14 -07:00
Scott Lahteine 277899c175 Move include _Bootscreen.h where needed 2016-07-26 12:37:13 -07:00
Scott Lahteine 83c4653c71 Include boards and macros ahead of configs 2016-07-26 12:19:50 -07:00
Scott Lahteine c6226bb0aa Unify config in a single include without nested includes 2016-07-25 23:04:19 -07:00
Scott Lahteine 2d378fac1b No need to include thermistortables.h in Configuration.h 2016-07-25 22:43:50 -07:00
Scott Lahteine 93ea281061 Split up Conditionals.h into two files
Rather than include twice, which is tricky but may confuse
2016-07-25 20:30:45 -07:00
Scott Lahteine fcc39e2b5f Clean up Transfer Buffer Size comment 2016-07-25 12:54:55 -07:00
Scott Lahteine 8633b644cf Merge pull request #4378 from thinkyhead/rc_debug_leveling_docs
Document DEBUG_LEVELING_FEATURE
2016-07-22 23:57:01 -07:00
Scott Lahteine bb9da6ebdd Document DEBUG_LEVELING_FEATURE 2016-07-22 23:37:41 -07:00
Scott Lahteine 91777dd76c Add DUAL_NOZZLE_DUPLICATION_MODE option 2016-07-22 16:22:56 -07:00
Scott Lahteine 194d9521c3 Merge pull request #4356 from thinkyhead/rc_simpler_run_z_probe
Unify run_z_probe
2016-07-19 19:02:39 -07:00
Scott Lahteine 4a6ed5e221 Use HOMING_FEEDRATE_Z for Z_PROBE_SPEED_FAST 2016-07-19 18:42:48 -07:00
AnHardt 09a3cc33e6 Unify run_z_probe
Unify run_z_probe
Add double touch for DELTAs.
Introduce Z_PROBE_SPEED_FAST and Z_PROBE_SPEED_SLOW
  defaulting to homing_feedrate_mm_m[Z_AXIS] and homing_feedrate_mm_m[Z_AXIS]/2
2016-07-19 18:42:48 -07:00
Scott Lahteine e44b37cdc2 motion section marker below homing speeds 2016-07-19 17:31:58 -07:00
Scott Lahteine 204fd6ec44 Set homing feedrates individually 2016-07-19 17:31:58 -07:00
Scott Lahteine 6abf916575 Reprapworld Keypad move step is 1mm 2016-07-19 16:40:39 -07:00
João Brázio b869fbc05e Update all config files with the new G12 options 2016-07-19 15:07:03 -07:00
Scott Lahteine 81e01152bb Merge pull request #4336 from thinkyhead/rc_bltouch_sensor
BLTouch probe sensor
2016-07-17 14:06:32 -07:00
Scott Lahteine 1583177ef4 BLTOUCH probe config option 2016-07-17 13:55:38 -07:00
Scott Lahteine 39706f3e57 Endstop invert flags as macros instead of const bool 2016-07-17 13:51:02 -07:00
Scott Lahteine 0fcd3706dd Replace ENDSTOPS_ONLY_FOR_HOMING with ENDSTOPS_ALWAYS_ON_DEFAULT 2016-07-17 13:35:21 -07:00
Scott Lahteine 671634bf11 Fix spacing after section header 2016-07-17 13:35:21 -07:00
Scott Lahteine 22b4cff423 New extruder type configuration options 2016-07-17 00:13:56 -07:00
Scott Lahteine bf16ae5a70 Merge pull request #4299 from jbrazio/feature/g27-park-nozzle
Implements park nozzle feature
2016-07-16 23:47:12 -07:00
João Brázio dfa1c45075 Adds a notice to vendors about the SHOW_CUSTOM_BOOTSCREEN directive 2016-07-17 01:15:17 +01:00
João Brázio 9a00108cb6 Adds the WEBSITE_URL as the boot screen line 2 2016-07-16 12:24:37 +01:00
João Brázio 336481ea81 Added G27 configuration options to all configs 2016-07-16 12:07:59 +01:00
João Brázio 68c343a09a Added G12 configuration options to all configs 2016-07-14 00:38:42 +01:00
Scott Lahteine a8b6b6a128 Merge pull request #4252 from thinkyhead/rc_rename_hpb
Replace PLA/ABS preheating with generic
2016-07-12 20:00:33 -07:00
Scott Lahteine 243ad4312a Merge pull request #4271 from thinkyhead/rc_X_DUAL_STEPPER_DRIVERS
X_DUAL_STEPPER_DRIVERS
2016-07-11 18:38:45 -07:00
Scott Lahteine 91bd6eade7 X_DUAL_STEPPER_DRIVERS configuration option 2016-07-11 10:22:19 -07:00
Scott Lahteine 928ff6487a Greek language pack from @psavva 2016-07-10 18:59:04 -07:00
Scott Lahteine 182c8d7f8f Dyze High Temp Thermistor Support 2016-07-10 17:59:05 -07:00
Scott Lahteine 1026e5b071 Replace PLA/ABS preheating with generic 2016-07-09 18:06:51 -07:00
Petr Zahradnik e282d69f63 Print job timer comment changed 2016-07-09 17:57:54 -07:00
AnHardt 4b44a23a36 Add TX-buffer for MarlinSerial
Similar to the current Arduino HardwareSerial
but with max. 256 byte buffer-size.

Deactivated by default.

The boards with AT90USB processor (USBCON) already use a TX-buffer.
2016-07-08 17:25:21 +02:00
AnHardt a129078927 Add an emergency-command parser to MarlinSerial (supporting M108)
Add an emergency-command parser to MarlinSerial's RX interrupt.

The parser tries to find and execute M108,M112,M410 before the commands disappear in the RX-buffer.

To avoid false positives for M117, comments and commands followed by filenames (M23, M28, M30, M32, M33) are filtered.

This enables Marlin to receive and react on the Emergency command at all times - regardless of whether the buffers are full or not. It remains to convince hosts to send the commands. To inform the hosts about the new feature a new entry in the M115-report was made. "`EMERGENCY_CODES:M112,M108,M410;`".

The parser is fast. It only ever needs two switch decisions and one assignment of the new state for every character.

One problem remains. If the host has sent an incomplete line before sending an emergency command the emergency command could be omitted when the parser is in `state_IGNORE`.
In that case the host should send "\ncommand\n"

Also introduces M108 to break the waiting for the heaters in M109, M190 and M303.

Rename `cancel_heatup` to `wait_for_heatup` to better see the purpose.
2016-07-07 16:37:22 -07:00
AnHardt 5126cce7fd Move Allen Key probe move scripts to their own functions
There was an hidden extra move after the scripts. This is configurable now.
Added the extra moves to the relevant configs.
2016-07-06 03:46:40 +02:00
Petr Zahradnik 43ff0ce35f Rewritten FILAMENT_CHANGE_ENABLE feature 2016-07-02 15:34:33 -07:00
Anthony Birkett 7a377c1d75 Add "About Printer" information menu.
Includes:
  *firmware version / branch / date.
  *extruder count
  *board information (name, serial details, power supply type)
  *thermistors (names, min/max temperatures)
  *printer statistics (PRINTCOUNTER details)

Thanks to @thinkyhead for contributions.
2016-07-02 15:22:26 -07:00
Scott Lahteine f84d85f761 Cleanup extruder runout configs 2016-06-30 01:40:41 -07:00
Scott Lahteine 683975cf90 Fix spelling in a config comment 2016-06-28 16:49:13 -07:00
Scott Lahteine 10da7ac86c Combine Z raise before/after options 2016-06-26 13:56:30 -07:00
Scott Lahteine 03c70c1990 SERVO_DEACTIVATION_DELAY => SERVO_DELAY 2016-06-23 14:33:29 -07:00
Scott Lahteine bd01592816 Goodbye MECHANICAL_PROBE 2016-06-22 17:13:33 -07:00
Scott Lahteine b590a7dee0 Make Z_RAISE_BETWEEN_PROBINGS a more general option 2016-06-22 14:00:44 -07:00
Scott Lahteine d50539583a Make XY_PROBE_SPEED a general probe option 2016-06-22 03:04:47 -07:00
Scott Lahteine 2798499b71 XY_TRAVEL_SPEED => XY_PROBE_SPEED 2016-06-22 02:45:25 -07:00
Scott Lahteine b0e47608e6 Merge pull request #4108 from esenapaj/Fix-for-PR-#4093
Fix for PR #4093 (Make Z Probe options independent of ABL), etc
2016-06-21 18:12:08 -07:00
Scott Lahteine 40cd20a236 Fix comments on EXPERIMENTAL_I2CBUS 2016-06-21 17:58:44 -07:00
esenapaj d583ea852d Standardize format description of Panel 2016-06-21 20:51:27 +09:00
esenapaj aa6d35bd49 Move code block of probe to appropriate position 2016-06-21 20:36:46 +09:00
Scott Lahteine 19fe93a5a9 Clean up configs for Z_MIN_PROBE_REPEATABILITY_TEST 2016-06-21 03:10:46 -07:00
Scott Lahteine 3996242e9d Allow Z_MIN_PROBE_REPEATABILITY_TEST solo 2016-06-21 01:56:40 -07:00
Scott Lahteine 9beb3f2f5e Merge pull request #4097 from thinkyhead/rc_fil_runout_cleanup
FIL_RUNOUT_INVERTING false by default
2016-06-19 19:46:14 -07:00
Scott Lahteine f215b30932 Merge pull request #4093 from thinkyhead/rc_probe_without_abl
Make Z Probe options independent of ABL
2016-06-19 19:44:25 -07:00
Scott Lahteine dfbf8b3c2c FIL_RUNOUT_INVERTING false by default 2016-06-19 19:25:26 -07:00
Scott Lahteine de12228758 Make Z Probe options independent of ABL 2016-06-19 18:47:27 -07:00
Scott Lahteine f8c278ce4d Cartesio UI display option in all configs 2016-06-19 17:39:46 -07:00
Scott Lahteine bd4ec727e7 Merge pull request #4066 from thinkyhead/rc_M851_with_probe
Make M851 standard with a bed probe
2016-06-17 17:32:55 -07:00
Scott Lahteine eab44b30d4 Safety and serial sections 2016-06-17 15:19:43 -07:00
Scott Lahteine fc56a547d1 Rename movement section to motion 2016-06-17 15:19:43 -07:00
Scott Lahteine 1000563d80 Make M851 standard with a bed probe 2016-06-17 15:19:42 -07:00
Scott Lahteine 47ce810f52 Remove support for XY servo endstops 2016-06-17 14:19:17 -07:00
Scott Lahteine d991a4c24a Merge pull request #4063 from thinkyhead/rc_remove_swp_files
Delete mysterious .swp files from #3609
2016-06-16 17:22:48 -07:00
Scott Lahteine ebbed2975e Delete mysterious .swp files from #3609 2016-06-16 16:42:03 -07:00
Scott Lahteine 02e5dad29a Include Croatian in language listings 2016-06-16 16:18:26 -07:00
Scott Lahteine f639044c24 Merge pull request #3609 from jbrazio/feature/config-version
Adds versioning for Configuration.h & Configuration_adv.h
2016-06-15 22:09:47 -07:00
esenapaj 741cda0e47 Follow-up the PR #3676(Advance extrusion algorithm – LIN_ADVANCE)
・Update forgotten example configurations
2016-06-15 00:10:15 +09:00
João Brázio 8ccd97e7cc
Updated all example configuration files 2016-06-12 00:36:15 +01:00
Reid Rankin 16212432c9 G20/21 and M149 support, and code_value() refactor
This is an update of MarlinDev PR #196.

G20/21: support for switching input units between millimeters and
inches.
M149: support for changing input temperature units.

In support of these changes, code_value() and code_value_short() are
replaced with an array of functions which handle converting to the
proper types and/or units.
2016-06-08 16:51:10 -07:00
Scott Lahteine cd441ce652 SINGLENOZZLE: EXTRUDERS versus HOTENDS 2016-06-03 17:38:03 -07:00
Scott Lahteine db0fd021d0 Z raise options independent of ABL so G28 can use them 2016-06-02 16:56:49 -07:00
Scott Lahteine 28fb1f8994 Tweak #endif comment for ABL GRID 2016-06-02 16:56:49 -07:00
Scott Lahteine 2bd4f33369 Merge pull request #3928 from thinkyhead/rc_allen_key_cleanup
Remove excess allen key probe examples from configs
2016-05-31 19:18:21 -07:00
Scott Lahteine a0b000d752 Support for SAV_3DGLCD OLED LCD controller 2016-05-31 14:41:16 -07:00
Scott Lahteine 43a71ef226 Remove excess allen key probe examples from configs 2016-05-30 18:26:53 -07:00
Edward Patel 06593833ff MBL: Move border macros to Configuration_adv.h 2016-05-30 20:50:16 +02:00
Edward Patel 92a27c37b3 MBL: Apply https://github.com/MarlinFirmware/Marlin/pull/3903 to example_configurations 2016-05-30 09:50:11 +02:00
Scott Lahteine fe3122774a Merge pull request #3806 from thinkyhead/rc_coreyz_support
Support for COREYZ. Fixes for COREXY, COREXZ
2016-05-26 18:50:43 -07:00
Scott Lahteine 89e630b2fb Merge pull request #3808 from thinkyhead/rc_singlenozzle
SINGLENOZZLE
2016-05-23 15:52:19 -07:00
Scott Lahteine 95fee8ca81 Add option for CoreYZ kinematics 2016-05-23 13:58:40 -07:00
Scott Lahteine c5130fd23b Additional instructions for controller reverse options 2016-05-20 18:14:50 -07:00
Scott Lahteine 69abfef82e Add "SINGLENOZZLE" extruder option 2016-05-20 15:45:11 -07:00
Scott Lahteine 1a6c72cb57 Apply to the rest of the configs 2016-05-20 11:52:27 -07:00
Scott Lahteine 8218558953 Update comments, rename next_ping_ms, followup to #3797 2016-05-19 16:44:57 -07:00
Scott Lahteine 07c9a11c3c Automatically set X2 stepper pins 2016-05-18 19:09:09 -07:00
Scott Lahteine 3016dfe484 Merge pull request #3744 from thinkyhead/rc_bezier_curves
Add BEZIER_CURVE_SUPPORT — G5 command
2016-05-17 13:57:38 -07:00
João Brázio f9a62f6a8e Added PRINTJOB_TIMER_AUTOSTART section to example config files 2016-05-14 15:22:45 -07:00
Scott Lahteine ddac17a195 Add BEZIER_CURVE_SUPPORT (G5 XYZEFIJPQ) 2016-05-14 14:52:08 -07:00
Scott Lahteine 9f6b8f7d5b Remove extra @section directive from configs 2016-05-14 14:51:09 -07:00
Scott Lahteine f13c4a9ec4 Merge pull request #3720 from jbrazio/feature/host-keepalive
Removes the DISABLE from HOST_KEEPALIVE
2016-05-14 14:39:31 -07:00
AnHardt b74af78736 Make arc support (G2/G3) configurable
Saves about 2669 bytes when deactivated. (About 1% for a AT2560, about __4%__ for a AT644!)
2016-05-13 13:27:45 +02:00
Scott Lahteine 14cd0f4c92 Merge pull request #3740 from thinkyhead/rc_lcd_home_options
Individual Axis Homing LCD menu items
2016-05-12 11:59:46 -07:00
João Brázio 09150cae79 Individual Axis Homing LCD menu items 2016-05-11 19:28:19 -07:00
Scott Lahteine 4dc4e2063f Add REVERSE_ENCODER_DIRECTION option 2016-05-11 15:39:28 -07:00
João Brázio 85b2c80838
Updated example configurations 2016-05-11 01:45:49 +01:00
João Brázio 5373ac6373
Updated example configurations 2016-05-10 13:42:00 +01:00
esenapaj 212b17d510 Fix for PR #3526(Configuration.h LCD & SDCard s...
Fix for PR #3526(Configuration.h LCD & SDCard section rewrite)

It removes duplicated BQ_LCD_SMART_CONTROLLER.
2016-05-03 21:35:02 +09:00
esenapaj 2fa4bc344c Some clean-up for example configuration files
Some clean-up for example configuration files

Follow-up and fix the PR #3253(Make the Autotune item(s) in the LCD menu optional):
・Update forgotten file(Felix/Configuration_DUAL.h)

Follow-up the PR #3526(Configuration.h LCD & SDCard section rewrite):
・Add section of RigidBot Panel to RepRapWorld/Megatronics/Configuration.h

Follow-up the PR #3576(Z Safe Homing for all):
・Adjust spacing

Follow-up and fix the PR #3625(Print job statistics):
・Update forgotten file(Felix/Configuration_DUAL.h)
・Remove ambiguous character "f" in top of RigidBot/Configuration.h
2016-05-02 21:16:00 +09:00
Scott Lahteine fbf69081b4 Updated comment for THERMAL_PROTECTION_BED 2016-05-01 13:12:51 -07:00