* Fixing the DUE serial port assignments: Now -1 means the SAM3x USB Device emulating a serial port, and 0 means the USB to serial adapter included as a programming port
* Improving the Fast IO port access implementation on Arduino DUE
* Implemented EEPROM emulation on Due by storing data on the internal FLASH (with wear leveling)
* Implemented a Software SPI for the ST7920 graphics display for the Arduino RAMPS for DUE, as the default one in u8glib is clocking data too fast on ARM, and the display does not understand it.
* Fixing the case where the serial port selected is the USB device
* Adding configuration for the Makerparts 3D printer (www.makerparts.net)
* Tuned MakerParts acceleration on X and Y axis so it never loses steps. Also adjusted pulses per mm to match default hw configuration
* Fine tuned Maximum acceleration for MakerParts printer
* Style cleanup
* Style cleanup (2)
* Style fixes (3)
* Fixing the DUE serial port assignments: Now -1 means the SAM3x USB Device emulating a serial port, and 0 means the USB to serial adapter included as a programming port
* Improving the Fast IO port access implementation on Arduino DUE
* Implemented EEPROM emulation on Due by storing data on the internal FLASH (with wear leveling)
* Implemented a Software SPI for the ST7920 graphics display for the Arduino RAMPS for DUE, as the default one in u8glib is clocking data too fast on ARM, and the display does not understand it.
* Fixing the case where the serial port selected is the USB device
* Adding configuration for the Makerparts 3D printer (www.makerparts.net)
* Tuned MakerParts acceleration on X and Y axis so it never loses steps. Also adjusted pulses per mm to match default hw configuration
* Fine tuned Maximum acceleration for MakerParts printer
* Style cleanup
* Style changes to u8g_dev_st7920_128_64_sw_spi.cpp
* Even more improvements to the FastIO HAL for DUE. Now WRITE() is 2 ASM instructions, if value is constant, and 5 cycles if value is not constant. Previously, it was 7..8 cycles
* After some problems and debugging, seems we need to align the interrupt vector table to 256 bytes, otherwise, the program sometimes stops working
* Moved comments out of macro, otherwise, token pasting does not properly work sometimes
* Improved Software SPI implementation on DUE: Now it honors the selected speed passed to spiInit(). This allows much faster SDCARD access, improving SDCARD menus and reducing latency
* Update u8g_dev_st7920_128_64_sw_spi.cpp
* Disabling EEPROM over FLASH emulatiion if an I2C or SPI EEPROM is present
* STM32F1 HAL
Adding files for STM32F1 HAL based on libmaple/stm32duino core.
Current persistent_store uses cardreader changes to be sent in separate
commit, but could be changed to use i2c eeprom.
There is another persistent_store implementation that uses the MCU flash memory
to emulate eeprom
Adding readme with some information about the stm32 HAL.
* Switch to Timer4 to avoid a hard reset on STM32F103C6 boards
On bluepill STM32F103C6 boards, using Timer5 results in a error() vector call. Switch to 4 since these are both general purpose, 16 bit timers.
* Add support for EEPROM emulation using Flash
Some low end machines doe not have EEPROM support. Simulate it using the last two pages of flash. Flash does not allow rewrite between erases, so skip writing the working version if that's enabled.
* Basic Pins for a malyan M200
This is a work in progress to go hand in hand with the STM32 work.
* Add support for ADC with DMA. This work has exposed a problem with the pin enumerations in STM boards vs what marlin expects (i.e, try defining PA0 as a temp pin). The hack can be removed with we go to fastio completely. To see this work, set something in adc_pins to a value like PA0 and connect your pullup resistor'd thermistor.
* Missing file - change HAL_adc_init to actually do something
We have an actual ADC init function now.
* Remove pinmode hack
Remove the pin mode hack that I was using to init PA0.
Updated Readme.md
* Several changes to timers and GPIO
Faster GPIO, and faster timer functions by accesing registers and
libmaple.
Still more changes pending for the Timer's code to skip using the
HardwareTimer class altogether.
Switch all enums to be within #defines
This change allows a user to have, for instance, TEMP_4 and TEMP_BED definied but nothing else. The enums which are not defined move "out", allowing the first ones to take the slots in the enum, and since the array is sized on ADC_PIN_COUNT, we always have the right size data and in order.
* Update Malyan M200 pins
Update Malyan M200 pins with correct fan values.
* Test all pins on actual hardware, update definitions
Some of the pin definitions were from knowlege base/pdfs. Now they've been tested against actual hardware. This should be very close to final.
* Update HAL_timers_Stm32f1.cpp
* Add sample configurations for Malyan M200
Add sample configuration for Malyan M200 without bed leveling, and move fan to auto cool E0 since this printer by default has only one fan.
Choose the timer based on MCU defintion. Timer5 is not valid on C8/CB class boards, so use Timer4 for the step timer.
readme.md update
* Updates to timers, and some stm32 boards definitiions
* Correct pin toggle macro.
* Remove duplicated Malyan M200 entry from pins.h
* Update configuration_store.cpp
* Formatting, indentation
* Formatting in HAL_Stm32f1.cpp
- Fix G26 Circle Drawing.
- Add default extrusion settings so machine can print lines on print bed
- Yet to be done: Get LCD Menu's to use these settings.
* Re-Print of same SD Memory Card file with single click
* Re-Print of same SD Memory Card file with single click
* This is the bugfix-v2.0.0 version of https://github.com/MarlinFirmware/Marlin/pull/8104
* Add GFX overlay to UBL mesh edit
Fixed misplaced HAS_TEMP_BED in dogm_bitmaps.h
rename _lcd_babystep_zoffset_overlay to _lcd_zoffset_overlay_gfx and move it out of BABYSTEP_ZPROBE_OFFSET to we can use it for over things. Add this function into UBL mesh edit screen.
update all Configuration.h to add ENABLE_MESH_EDIT_GFX_OVERLAY
* Add Sanity to UBL insanity
Need to check for DOGLCD otherwise error out.
* Get UBL Mesh Generation, Mesh Save & Mesh Load working with 32-Bit platforms
* clean up read_data() and write_data() for non-LPC1768 HAL's
* Get read_data() and write_data() return codes consistent
All HAL's read_data() and write_data() return false if they succeed.
* Get read_data() and write_data() return codes to be consistent
Make read_data() and write_data() return true if an error happens.
* Say UBL is now checked out on machine types in default Configuration.h file.
* Add files via upload
* Add files via upload
* Add files via upload
* Checked LCD / edited / revised pins_MKS_BASE.h
As requested :)
* Delete Configuration_adv.h
* Delete Configuration.h
* Deleted /Marlin/Marlin/src/config/examples/MksSbase/*.* and moved them to /Marlin/Marlin/src/config/examples/Mks/Sbase/*.*
* Add files via upload
Same as #7728 but for 2.0.x,
Lot of cleanup and remove references in whole code to other "LED files" than leds.h. Now will be much easier to add next drivers/libraries. e.g. FastLED. But bad news, currently FastLED is suporting only RGB devices (no RGBW)
Adding files for STM32F1 HAL based on libmaple/stm32duino core.
Current persistent_store uses cardreader changes to be sent in separate
commit, but could be changed to use i2c eeprom.
